lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [thread-next>] [day] [month] [year] [list]
Message-Id: <20230118044418.875-3-linux.amoon@gmail.com>
Date:   Wed, 18 Jan 2023 04:44:10 +0000
From:   Anand Moon <linux.amoon@...il.com>
To:     Rob Herring <robh+dt@...nel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
        Neil Armstrong <neil.armstrong@...aro.org>,
        Kevin Hilman <khilman@...libre.com>,
        Jerome Brunet <jbrunet@...libre.com>,
        Martin Blumenstingl <martin.blumenstingl@...glemail.com>
Cc:     linux-amlogic@...ts.infradead.org,
        Matthias Kaehlcke <mka@...omium.org>,
        Alexander Stein <alexander.stein@...tq-group.com>,
        Johan Hovold <johan@...nel.org>, devicetree@...r.kernel.org,
        linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org
Subject: [PATCH v2 2/9] ARM: dts: amlogic: Used onboard usb hub reset to enable usb hub

On Odroid c1 previously use gpio-hog to reset the usb hub,
switch to used on board usb hub reset to enable the usb hub
and enable power to usb hub.

Add usb hub regulator as per the schematic.

Signed-off-by: Anand Moon <linux.amoon@...il.com>
---
v2 - drop the vendor name from compatible string.
   - move the hub node to USB controller node.
   - drop the usb_otg_pwr since it only liked to OTG port
     and link p5v0 to the vdd-supply.
---
 arch/arm/boot/dts/meson8b-odroidc1.dts | 24 +++++++++++-------------
 1 file changed, 11 insertions(+), 13 deletions(-)

diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts
index 04356bc639fa..d1f9ce4742a8 100644
--- a/arch/arm/boot/dts/meson8b-odroidc1.dts
+++ b/arch/arm/boot/dts/meson8b-odroidc1.dts
@@ -281,19 +281,6 @@ &gpio_ao {
 			  "J7 Header Pin 6", "J7 Header Pin 5",
 			  "J7 Header Pin 7", "HDMI_CEC",
 			  "SYS_LED", "", "";
-
-	/*
-	 * WARNING: The USB Hub on the Odroid-C1/C1+ needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller.
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
 };
 
 &ir_receiver {
@@ -381,5 +368,16 @@ &usb1_phy {
 };
 
 &usb1 {
+	dr_mode = "host";
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
+
+	hub@1 {
+		/* Genesys Logic GL852G usb hub */
+		compatible = "usb5e3,610";
+		reg = <1>;
+		vdd-supply = <&p5v0>;
+		reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
+	};
 };
-- 
2.38.1

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ