linux-kernel - Re: [PATCH v2 3/9] arm64: dts: amlogic: Used onboard usb hub reset on odroid c2

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite for Android: free password hash cracker in your pocket

[<prev] [next>] [<thread-prev] [day] [month] [year] [list]

Message-ID: <3f0ade86-cab1-1f5a-fd49-326802473b76@linaro.org>
Date:   Wed, 18 Jan 2023 09:27:01 +0100
From:   Neil Armstrong <neil.armstrong@...aro.org>
To:     Anand Moon <linux.amoon@...il.com>,
        Rob Herring <robh+dt@...nel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
        Kevin Hilman <khilman@...libre.com>,
        Jerome Brunet <jbrunet@...libre.com>,
        Martin Blumenstingl <martin.blumenstingl@...glemail.com>
Cc:     linux-amlogic@...ts.infradead.org,
        Matthias Kaehlcke <mka@...omium.org>,
        Alexander Stein <alexander.stein@...tq-group.com>,
        Johan Hovold <johan@...nel.org>, devicetree@...r.kernel.org,
        linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH v2 3/9] arm64: dts: amlogic: Used onboard usb hub reset on
 odroid c2

On 18/01/2023 05:44, Anand Moon wrote:
> On Odroid c2 previously use gpio-hog to reset the usb hub,
> switch to used on-board usb hub reset to enable the usb hub
> and enable power to hub.
> 
> Signed-off-by: Anand Moon <linux.amoon@...il.com>
> ---
> v2 - drop the vendor name from compatible string.
>     - move the hub node to USB controller node.
>     - drop the usb_otg_pwr since it only liked to OTG port
>           and link p5v0 to the vdd-supply.
> ---
>   .../boot/dts/amlogic/meson-gxbb-odroidc2.dts  | 26 ++++++++-----------
>   1 file changed, 11 insertions(+), 15 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> index 201596247fd9..01356437a077 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
> @@ -250,21 +250,6 @@ eth_phy0: ethernet-phy@0 {
>   	};
>   };
>   
> -&gpio_ao {
> -	/*
> -	 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
> -	 * to be turned high in order to be detected by the USB Controller
> -	 * This signal should be handled by a USB specific power sequence
> -	 * in order to reset the Hub when USB bus is powered down.
> -	 */
> -	hog-0 {
> -		gpio-hog;
> -		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
> -		output-high;
> -		line-name = "usb-hub-reset";
> -	};
> -};
> -
>   &hdmi_tx {
>   	status = "okay";
>   	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
> @@ -414,5 +399,16 @@ &usb0 {
>   };
>   
>   &usb1 {
> +	dr_mode = "host";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
>   	status = "okay";
> +
> +	hub@1 {
> +		/* Genesys Logic GL852G USB 2.0 hub */
> +		compatible = "usb5e3,610";
> +		reg = <1>;
> +		vdd-supply = <&p5v0>;
> +		reset-gpio = <&gpio_ao GPIOAO_4 GPIO_ACTIVE_LOW>;
> +	};
>   };

Reviewed-by: Neil Armstrong <neil.armstrong@...aro.org>