Message-ID: <e7e9704c-df97-2c27-2955-959d847a8bb8@linaro.org>
Date:   Wed, 1 Feb 2023 20:27:37 +0100
From:   Daniel Lezcano <daniel.lezcano@...aro.org>
To:     "Rafael J. Wysocki" <rafael@...nel.org>
Cc:     srinivas.pandruvada@...ux.intel.com, linux-pm@...r.kernel.org,
        linux-kernel@...r.kernel.org, rui.zhang@...el.com,
        Amit Kucheria <amitk@...nel.org>
Subject: Re: [PATCH 1/3] thermal/drivers/intel: Use generic trip points for
 quark_dts

On 01/02/2023 19:47, Rafael J. Wysocki wrote:
> On Wed, Feb 1, 2023 at 11:42 AM Daniel Lezcano
> <daniel.lezcano@...aro.org> wrote:
>>
>> On 31/01/2023 20:11, Rafael J. Wysocki wrote:
>>> On Tue, Jan 31, 2023 at 5:41 PM Daniel Lezcano
>>> <daniel.lezcano@...aro.org> wrote:
>>>>
>>>> On 26/01/2023 15:15, Rafael J. Wysocki wrote:
>>>>> On Wed, Jan 18, 2023 at 7:16 PM Daniel Lezcano
>>>>> <daniel.lezcano@...aro.org> wrote:
>>>>>>
>>>>>> The thermal framework gives the possibility to register the trip
>>>>>> points with the thermal zone. When that is done, no get_trip_* ops are
>>>>>> needed and they can be removed.
>>>>>>
>>>>>> Convert ops content logic into generic trip points and register them with the
>>>>>> thermal zone.
>>>>>>
>>>>>> Signed-off-by: Daniel Lezcano <daniel.lezcano@...aro.org>
>>>>>> ---
>>>>
>>>> [ ... ]
>>>>
>>>>>> -       aux_entry->tzone = thermal_zone_device_register("quark_dts",
>>>>>> -                       QRK_MAX_DTS_TRIPS,
>>>>>> -                       wr_mask,
>>>>>> -                       aux_entry, &tzone_ops, NULL, 0, polling_delay);
>>>>>> +       err = get_trip_temp(QRK_DTS_ID_TP_CRITICAL, &temperature);
>>>>>> +       if (err)
>>>>>> +               goto err_ret;
>>>>>> +
>>>>>> +       aux_entry->trips[QRK_DTS_ID_TP_CRITICAL].temperature = temperature;
>>>>>> +       aux_entry->trips[QRK_DTS_ID_TP_CRITICAL].type = THERMAL_TRIP_CRITICAL;
>>>>>> +
>>>>>> +       err = get_trip_temp(QRK_DTS_ID_TP_HOT, &temperature);
>>>>>> +       if (err)
>>>>>> +               goto err_ret;
>>>>>
>>>>> If I'm not mistaken, this won't even try to register the thermal zone
>>>>> if at least one trip cannot be initialized, but previously it was
>>>>> registered in that case, but the trips that failed to respond were
>>>>> disabled.
>>>>>
>>>>> This is a change in behavior that would at least need to be documented
>>>>> in the changelog, but it isn't.
>>>>>
>>>>> I'm not sure if it is safe to make even, however.
>>>>
>>>> Thanks for catching this.
>>>>
>>>> Two solutions:
>>>>
>>>> 1. Set the temperature to THERMAL_TEMP_INVALID and change
>>>> get_thermal_trip() to return -EINVAL or -ERANGE if the temperature is
>>>> THERMAL_TEMP_INVALID
>>>>
>>>> 2. Register only the valid trip points.
>>>>
>>>> What would be the preferable way ?
>>>
>>> I think that the trip points that are registered currently need to
>>> still be registered after the change.
>>>
>>> Does registering a trip point with the temperature set to
>>> THERMAL_TEMP_INVALID cause it to be effectively disabled?
>>
>> The initial behavior before the changes is:
>>
>> The function thermal_zone_device_register() will go through all the trip
>> points and call thermal_zone_get_trip(), resulting in a call to
>> ops->get_trip_temp(). If the call fails, the trip point is tagged as
>> disabled and will stay in this state forever, so discarded in the trip
>> point crossed detection.
>>
>> That does not report an error and the trip point is showed in sysfs but
>> in a inconsistent state as it is actually disabled. Reading the trip
>> point will return an error or not, but it is in any case disabled in the
>> thermal framework. The userspace does not have the information about the
>> trip point being disabled, so showing it up regardless its state is
>> pointless and prone to confusion for the userspace.
>>
>> IMO, it would be more sane to register the trip points which are
>> actually valid, so invalid trip points are not showed up and does
>> prevent extra complexity in the thermal core to handle them.
> 
> Except when the trip point can be updated to become a valid one later,
> for example in response to a system configuration change.  That can
> happen to ACPI-provided trip points, for example.
> 
> I don't think that this is an issue for this particular driver, but
> the core needs to handle that case anyway.

Yes, but the point is the core code never handled that case.

If the trip point fails when registering the thermal zone (and this is 
not related to our changes), the trip point is added to the disabled 
trips bitmap and then whatever the action to validate the trip point, it 
remains disabled for the thermal framework. There is no action to enable 
it (except I missed something).

> Moreover, there is the case when trip points only become relevant when
> their temperatures are set via ops->set_trip_temp() and they are
> THERMAL_TEMP_INVALID initially, which needs to be handled by the core
> either.

Ok, then I guess the simplest change is to assign THERMAL_TEMP_INVALID 
in this driver, if get_trip_temp fails at the initialization time.

Later we can add a thermal_zone_device_update_trips() with the needed 
locking and actions related to the update.

> When the driver has no way to update trip point temperatures, either
> through a firmware notification or via ops->set_trip_temp(), then I
> agree that registering them is not very useful if their temperatures
> cannot be determined.

+1

Thanks!

-- 
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

Powered by blists - more mailing lists