| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <Y9znh4ydK37V/Eyo@hovoldconsulting.com>
Date: Fri, 3 Feb 2023 11:52:55 +0100
From: Johan Hovold <johan@...nel.org>
To: Abel Vesa <abel.vesa@...aro.org>
Cc: Andy Gross <agross@...nel.org>,
Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konrad.dybcio@...aro.org>,
Rob Herring <robh@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
"vkoul@...nel.org" <vkoul@...nel.org>,
Kishon Vijay Abraham I <kishon@...nel.org>,
linux-arm-msm@...r.kernel.org, linux-phy@...ts.infradead.org,
devicetree@...r.kernel.org,
Linux Kernel Mailing List <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v4 6/8] phy: qcom-qmp-combo: Add support for SM8550
On Thu, Feb 02, 2023 at 03:25:09PM +0200, Abel Vesa wrote:
> Add SM8550 specific register layout and table configs.
>
> Signed-off-by: Abel Vesa <abel.vesa@...aro.org>
> ---
>
> The v3 version of this patch was here:
> https://lore.kernel.org/all/20230126131415.1453741-7-abel.vesa@linaro.org/
>
> Changes since v3:
> * switched dp_tx and dp_tx2 to off->dp_tx0 and off->dp_tx1, like Neil
> suggested
>
> Changes since v2:
> * none
>
> Changes since v1:
> * switched from qmp-usb to qmp-combo as it will support DP also
> * changed all hex offset values to lowercase, like Vinod suggested
>
> drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 409 +++++++++++++++++++++-
> 1 file changed, 404 insertions(+), 5 deletions(-)
> struct qmp_combo_offsets {
> @@ -808,6 +1039,8 @@ struct qmp_combo_offsets {
> u16 usb3_pcs;
> u16 usb3_pcs_usb;
> u16 dp_serdes;
> + u16 dp_tx0;
> + u16 dp_tx1;
As I mentioned off-list last week, this should be rebased on Luca's
patch adding support for SM6350:
https://lore.kernel.org/lkml/20230120-sm6350-usbphy-v4-2-4d700a90ba16@fairphone.com/
> u16 dp_dp_phy;
> };
>
> @@ -927,6 +1160,9 @@ static int qmp_v4_calibrate_dp_phy(struct qmp_combo *qmp);
>
> static int qmp_v5_configure_dp_phy(struct qmp_combo *qmp);
>
> +static void qmp_v6_dp_aux_init(struct qmp_combo *qmp);
> +static int qmp_v6_configure_dp_phy(struct qmp_combo *qmp);
> +
> static inline void qphy_setbits(void __iomem *base, u32 offset, u32 val)
> {
> u32 reg;
> @@ -985,9 +1221,27 @@ static const struct qmp_combo_offsets qmp_combo_offsets_v5 = {
> .usb3_pcs = 0x1400,
> .usb3_pcs_usb = 0x1700,
> .dp_serdes = 0x2000,
> + .dp_tx0 = 0x2200,
> + .dp_tx1 = 0x2600,
This would break sc8280xp and does not in anyway belong in this patch.
You can't just randomly change register offsets for an old SoC when
adding support for a new one.
> .dp_dp_phy = 0x2200,
> };
>
> +static const struct qmp_combo_offsets qmp_combo_offsets_v6 = {
> + .com = 0x0000,
> + .txa = 0x1200,
> + .rxa = 0x1400,
> + .txb = 0x1600,
> + .rxb = 0x1800,
> + .usb3_serdes = 0x1000,
> + .usb3_pcs_misc = 0x1a00,
> + .usb3_pcs = 0x1c00,
> + .usb3_pcs_usb = 0x1f00,
> + .dp_serdes = 0x2000,
> + .dp_tx0 = 0x2200,
> + .dp_tx1 = 0x2600,
> + .dp_dp_phy = 0x2a00,
> +};
> +
> static const struct qmp_phy_cfg sc7180_usb3dpphy_cfg = {
> .serdes_tbl = qmp_v3_usb3_serdes_tbl,
> .serdes_tbl_num = ARRAY_SIZE(qmp_v3_usb3_serdes_tbl),
> @@ -1219,6 +1473,54 @@ static const struct qmp_phy_cfg sm8250_usb3dpphy_cfg = {
> .has_pwrdn_delay = true,
> };
>
> +static const struct qmp_phy_cfg sm8550_usb3dpphy_cfg = {
> + .offsets = &qmp_combo_offsets_v6,
> +
> + .serdes_tbl = sm8550_usb3_serdes_tbl,
> + .serdes_tbl_num = ARRAY_SIZE(sm8550_usb3_serdes_tbl),
> + .tx_tbl = sm8550_usb3_tx_tbl,
> + .tx_tbl_num = ARRAY_SIZE(sm8550_usb3_tx_tbl),
> + .rx_tbl = sm8550_usb3_rx_tbl,
> + .rx_tbl_num = ARRAY_SIZE(sm8550_usb3_rx_tbl),
> + .pcs_tbl = sm8550_usb3_pcs_tbl,
> + .pcs_tbl_num = ARRAY_SIZE(sm8550_usb3_pcs_tbl),
> + .pcs_usb_tbl = sm8550_usb3_pcs_usb_tbl,
> + .pcs_usb_tbl_num = ARRAY_SIZE(sm8550_usb3_pcs_usb_tbl),
> +
> + .dp_serdes_tbl = qmp_v6_dp_serdes_tbl,
> + .dp_serdes_tbl_num = ARRAY_SIZE(qmp_v6_dp_serdes_tbl),
> + .dp_tx_tbl = qmp_v6_dp_tx_tbl,
> + .dp_tx_tbl_num = ARRAY_SIZE(qmp_v6_dp_tx_tbl),
> +
> + .serdes_tbl_rbr = qmp_v6_dp_serdes_tbl_rbr,
> + .serdes_tbl_rbr_num = ARRAY_SIZE(qmp_v6_dp_serdes_tbl_rbr),
> + .serdes_tbl_hbr = qmp_v6_dp_serdes_tbl_hbr,
> + .serdes_tbl_hbr_num = ARRAY_SIZE(qmp_v6_dp_serdes_tbl_hbr),
> + .serdes_tbl_hbr2 = qmp_v6_dp_serdes_tbl_hbr2,
> + .serdes_tbl_hbr2_num = ARRAY_SIZE(qmp_v6_dp_serdes_tbl_hbr2),
> + .serdes_tbl_hbr3 = qmp_v6_dp_serdes_tbl_hbr3,
> + .serdes_tbl_hbr3_num = ARRAY_SIZE(qmp_v6_dp_serdes_tbl_hbr3),
> +
> + .swing_hbr_rbr = &qmp_dp_v5_voltage_swing_hbr_rbr,
> + .pre_emphasis_hbr_rbr = &qmp_dp_v6_pre_emphasis_hbr_rbr,
> + .swing_hbr3_hbr2 = &qmp_dp_v5_voltage_swing_hbr3_hbr2,
> + .pre_emphasis_hbr3_hbr2 = &qmp_dp_v5_pre_emphasis_hbr3_hbr2,
> +
> + .dp_aux_init = qmp_v6_dp_aux_init,
> + .configure_dp_tx = qmp_v4_configure_dp_tx,
> + .configure_dp_phy = qmp_v6_configure_dp_phy,
> + .calibrate_dp_phy = qmp_v4_calibrate_dp_phy,
> +
> + .regs = qmp_v4_usb3phy_regs_layout,
> + .clk_list = qmp_v4_phy_clk_l,
> + .num_clks = ARRAY_SIZE(qmp_v4_phy_clk_l),
> + .reset_list = msm8996_usb3phy_reset_l,
> + .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
> + .vreg_list = qmp_phy_vreg_l,
> + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
> + .pcs_usb_offset = 0x300,
This field is not used with the new bindings and should be removed.
> +};
> +
> static void qmp_combo_configure_lane(void __iomem *base,
> const struct qmp_phy_init_tbl tbl[],
> int num,
> @@ -1529,6 +1831,33 @@ static void qmp_v4_dp_aux_init(struct qmp_combo *qmp)
> qmp->dp_dp_phy + QSERDES_V4_DP_PHY_AUX_INTERRUPT_MASK);
> }
>
> +static void qmp_v6_dp_aux_init(struct qmp_combo *qmp)
> +{
> + writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_PSR_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
> + DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN,
> + qmp->dp_dp_phy + QSERDES_DP_PHY_PD_CTL);
> +
> + /* Turn on BIAS current for PHY/PLL */
> + writel(0x17, qmp->dp_serdes + QSERDES_V6_COM_PLL_BIAS_EN_CLK_BUFLR_EN);
> +
> + writel(0x00, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG0);
> + writel(0x13, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG1);
> + writel(0xa4, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG2);
> + writel(0x00, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG3);
> + writel(0x0a, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG4);
> + writel(0x26, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG5);
> + writel(0x0a, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG6);
> + writel(0x03, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG7);
> + writel(0xb7, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG8);
> + writel(0x03, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG9);
> + qmp->dp_aux_cfg = 0;
> +
> + writel(PHY_AUX_STOP_ERR_MASK | PHY_AUX_DEC_ERR_MASK |
> + PHY_AUX_SYNC_ERR_MASK | PHY_AUX_ALIGN_ERR_MASK |
> + PHY_AUX_REQ_ERR_MASK,
> + qmp->dp_dp_phy + QSERDES_V4_DP_PHY_AUX_INTERRUPT_MASK);
> +}
> +
> static void qmp_v4_configure_dp_tx(struct qmp_combo *qmp)
> {
> /* Program default values before writing proper values */
> @@ -1542,7 +1871,10 @@ static void qmp_v4_configure_dp_tx(struct qmp_combo *qmp)
> QSERDES_V4_TX_TX_EMP_POST1_LVL);
> }
>
> -static int qmp_v45_configure_dp_phy(struct qmp_combo *qmp)
> +static int qmp_v456_configure_dp_phy(struct qmp_combo *qmp,
> + unsigned int com_resetm_ctrl_reg,
> + unsigned int com_c_ready_status_reg,
> + unsigned int dp_phy_status_reg)
> {
> const struct phy_configure_opts_dp *dp_opts = &qmp->dp_opts;
> u32 phy_vco_div, status;
Looks like something is missing here as you're not using the new
parameters anywhere?
> @@ -1639,7 +1971,9 @@ static int qmp_v4_configure_dp_phy(struct qmp_combo *qmp)
> u32 status;
> int ret;
>
> - ret = qmp_v45_configure_dp_phy(qmp);
> + ret = qmp_v456_configure_dp_phy(qmp, QSERDES_V4_COM_RESETSM_CNTRL,
> + QSERDES_V4_COM_C_READY_STATUS,
> + QSERDES_V4_DP_PHY_STATUS);
> if (ret < 0)
> return ret;
>
> @@ -1701,7 +2035,9 @@ static int qmp_v5_configure_dp_phy(struct qmp_combo *qmp)
> u32 status;
> int ret;
>
> - ret = qmp_v45_configure_dp_phy(qmp);
> + ret = qmp_v456_configure_dp_phy(qmp, QSERDES_V4_COM_RESETSM_CNTRL,
> + QSERDES_V4_COM_C_READY_STATUS,
> + QSERDES_V4_DP_PHY_STATUS);
> if (ret < 0)
> return ret;
>
> @@ -1750,6 +2086,65 @@ static int qmp_v5_configure_dp_phy(struct qmp_combo *qmp)
> return 0;
> }
>
> +static int qmp_v6_configure_dp_phy(struct qmp_combo *qmp)
> +{
> + const struct phy_configure_opts_dp *dp_opts = &qmp->dp_opts;
> + u32 bias0_en, drvr0_en, bias1_en, drvr1_en;
> + bool reverse = false;
> + u32 status;
> + int ret;
> +
> + ret = qmp_v456_configure_dp_phy(qmp, QSERDES_V6_COM_RESETSM_CNTRL,
> + QSERDES_V6_COM_C_READY_STATUS,
> + QSERDES_V6_DP_PHY_STATUS);
> + if (ret < 0)
> + return ret;
> +
> + if (dp_opts->lanes == 1) {
> + bias0_en = reverse ? 0x3e : 0x1a;
> + drvr0_en = reverse ? 0x13 : 0x10;
> + bias1_en = reverse ? 0x15 : 0x3e;
> + drvr1_en = reverse ? 0x10 : 0x13;
> + } else if (dp_opts->lanes == 2) {
> + bias0_en = reverse ? 0x3f : 0x15;
> + drvr0_en = 0x10;
> + bias1_en = reverse ? 0x15 : 0x3f;
> + drvr1_en = 0x10;
> + } else {
> + bias0_en = 0x3f;
> + bias1_en = 0x3f;
> + drvr0_en = 0x10;
> + drvr1_en = 0x10;
> + }
> +
> + writel(drvr0_en, qmp->dp_tx + QSERDES_V4_TX_HIGHZ_DRVR_EN);
> + writel(bias0_en, qmp->dp_tx + QSERDES_V4_TX_TRANSCEIVER_BIAS_EN);
> + writel(drvr1_en, qmp->dp_tx2 + QSERDES_V4_TX_HIGHZ_DRVR_EN);
> + writel(bias1_en, qmp->dp_tx2 + QSERDES_V4_TX_TRANSCEIVER_BIAS_EN);
> +
> + writel(0x18, qmp->dp_dp_phy + QSERDES_DP_PHY_CFG);
> + udelay(2000);
> + writel(0x19, qmp->dp_dp_phy + QSERDES_DP_PHY_CFG);
> +
> + if (readl_poll_timeout(qmp->dp_dp_phy + QSERDES_V6_DP_PHY_STATUS,
> + status,
> + ((status & BIT(1)) > 0),
> + 500,
> + 10000))
> + return -ETIMEDOUT;
> +
> + writel(0x0a, qmp->dp_tx + QSERDES_V4_TX_TX_POL_INV);
> + writel(0x0a, qmp->dp_tx2 + QSERDES_V4_TX_TX_POL_INV);
> +
> + writel(0x27, qmp->dp_tx + QSERDES_V4_TX_TX_DRV_LVL);
> + writel(0x27, qmp->dp_tx2 + QSERDES_V4_TX_TX_DRV_LVL);
> +
> + writel(0x20, qmp->dp_tx + QSERDES_V4_TX_TX_EMP_POST1_LVL);
> + writel(0x20, qmp->dp_tx2 + QSERDES_V4_TX_TX_EMP_POST1_LVL);
> +
> + return 0;
> +}
> +
> /*
> * We need to calibrate the aux setting here as many times
> * as the caller tries
> @@ -2640,8 +3035,8 @@ static int qmp_combo_parse_dt(struct qmp_combo *qmp)
> qmp->pcs_usb = base + offs->usb3_pcs_usb;
>
> qmp->dp_serdes = base + offs->dp_serdes;
> - qmp->dp_tx = base + offs->txa;
> - qmp->dp_tx2 = base + offs->txb;
> + qmp->dp_tx = base + offs->dp_tx0;
> + qmp->dp_tx2 = base + offs->dp_tx1;
Again, this breaks sc8280xp. Rebasing on Luca's patch and dropping the
offsets you're adding to the v5 offsets should avoid that.
> qmp->dp_dp_phy = base + offs->dp_dp_phy;
>
> qmp->pipe_clk = devm_clk_get(dev, "usb3_pipe");
> @@ -2792,6 +3187,10 @@ static const struct of_device_id qmp_combo_of_match_table[] = {
> .compatible = "qcom,sm8250-qmp-usb3-dp-phy",
> .data = &sm8250_usb3dpphy_cfg,
> },
> + {
> + .compatible = "qcom,sm8550-qmp-usb3-dp-phy",
> + .data = &sm8550_usb3dpphy_cfg,
> + },
> { }
> };
> MODULE_DEVICE_TABLE(of, qmp_combo_of_match_table);
Johan
Powered by blists - more mailing lists