[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20230209111459.1891941-19-sashal@kernel.org>
Date: Thu, 9 Feb 2023 06:14:38 -0500
From: Sasha Levin <sashal@...nel.org>
To: linux-kernel@...r.kernel.org, stable@...r.kernel.org
Cc: Andrey Konovalov <andrey.konovalov@...aro.org>,
"David S . Miller" <davem@...emloft.net>,
Sasha Levin <sashal@...nel.org>, vkoul@...nel.org,
peppe.cavallaro@...com, alexandre.torgue@...s.st.com,
joabreu@...opsys.com, edumazet@...gle.com, kuba@...nel.org,
pabeni@...hat.com, mcoquelin.stm32@...il.com, veekhee@...le.com,
tee.min.tan@...ux.intel.com, ruppala@...dia.com,
jonathanh@...dia.com, netdev@...r.kernel.org,
linux-stm32@...md-mailman.stormreply.com,
linux-arm-kernel@...ts.infradead.org
Subject: [PATCH AUTOSEL 6.1 19/38] net: stmmac: do not stop RX_CLK in Rx LPI state for qcs404 SoC
From: Andrey Konovalov <andrey.konovalov@...aro.org>
[ Upstream commit 54aa39a513dbf2164ca462a19f04519b2407a224 ]
Currently in phy_init_eee() the driver unconditionally configures the PHY
to stop RX_CLK after entering Rx LPI state. This causes an LPI interrupt
storm on my qcs404-base board.
Change the PHY initialization so that for "qcom,qcs404-ethqos" compatible
device RX_CLK continues to run even in Rx LPI state.
Signed-off-by: Andrey Konovalov <andrey.konovalov@...aro.org>
Signed-off-by: David S. Miller <davem@...emloft.net>
Signed-off-by: Sasha Levin <sashal@...nel.org>
---
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c | 2 ++
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 3 ++-
include/linux/stmmac.h | 1 +
3 files changed, 5 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
index 835caa15d55ff..732774645c1a6 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
@@ -560,6 +560,8 @@ static int qcom_ethqos_probe(struct platform_device *pdev)
plat_dat->has_gmac4 = 1;
plat_dat->pmt = 1;
plat_dat->tso_en = of_property_read_bool(np, "snps,tso");
+ if (of_device_is_compatible(np, "qcom,qcs404-ethqos"))
+ plat_dat->rx_clk_runs_in_lpi = 1;
ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
if (ret)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 4bba0444c764a..84e1740b12f1b 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -1077,7 +1077,8 @@ static void stmmac_mac_link_up(struct phylink_config *config,
stmmac_mac_set(priv, priv->ioaddr, true);
if (phy && priv->dma_cap.eee) {
- priv->eee_active = phy_init_eee(phy, 1) >= 0;
+ priv->eee_active =
+ phy_init_eee(phy, !priv->plat->rx_clk_runs_in_lpi) >= 0;
priv->eee_enabled = stmmac_eee_init(priv);
priv->tx_lpi_enabled = priv->eee_enabled;
stmmac_set_eee_pls(priv, priv->hw, true);
diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
index fb2e88614f5d1..313edd19bf545 100644
--- a/include/linux/stmmac.h
+++ b/include/linux/stmmac.h
@@ -252,6 +252,7 @@ struct plat_stmmacenet_data {
int rss_en;
int mac_port_sel_speed;
bool en_tx_lpi_clockgating;
+ bool rx_clk_runs_in_lpi;
int has_xgmac;
bool vlan_fail_q_en;
u8 vlan_fail_q;
--
2.39.0
Powered by blists - more mailing lists