linux-kernel - Re: Aw: Re: Re: [PATCH v3 0/5] arm: dts: mt7623: relocate gmacs, mt7530 switch, and add port@5

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-ID: <A329B2DF-04B7-40FA-BBCE-1F1012A6DBBD@public-files.de>
Date:   Sat, 18 Feb 2023 20:11:51 +0100
From:   Frank Wunderlich <frank-w@...lic-files.de>
To:     Arınç ÜNAL <arinc.unal@...nc9.com>
CC:     Rob Herring <robh+dt@...nel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
        Matthias Brugger <matthias.bgg@...il.com>,
        AngeloGioacchino Del Regno 
        <angelogioacchino.delregno@...labora.com>,
        devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
        linux-arm-kernel@...ts.infradead.org,
        linux-mediatek@...ts.infradead.org, erkin.bozoglu@...ont.com
Subject: Re: Aw: Re: Re: [PATCH v3 0/5] arm: dts: mt7623: relocate gmacs, mt7530 switch, and add port@5

Am 18. Februar 2023 18:02:11 MEZ schrieb "Arınç ÜNAL" <arinc.unal@...nc9.com>:
>On 18.02.2023 15:18, Frank Wunderlich wrote:
>> Hi,
>> 
>>> Gesendet: Samstag, 18. Februar 2023 um 11:49 Uhr
>>> Von: "Arınç ÜNAL" <arinc.unal@...nc9.com>
>>> An: "Frank Wunderlich" <frank-w@...lic-files.de>
>> 
>>> On 18.02.2023 13:24, Frank Wunderlich wrote:

>Ok, so according to your tests, traffic through gmac1 is not very good. gmac0 should be the default DSA master.

>By the way, did you make a bug report of this, by sending a mail to netdev mailing list or some other way?

No,not yet, because gmac1 is not yet used and i had very limited time. I'm not sure it is an issue in mt7530 driver or mtk_soc_eth, not idea how to figure this out. Maybe it can be fixed with a delayed rgmii phy-mode (rgmii-rx-id i guess as traffic affected is rx on switch,tx on gmac). 

>> isn't there a way to leave ports by default on the the better gmac (gmac0=trgmii)?
>> maybe moving port5 below port6...not nice, but then port6 is the first cpu found.
>
>This could be done but it comes off as an improper way to me.

Just thought about a way without the need of changing driver or adding a new dt property which can be wrongly used (who prevents anybody set the "default-cpu" property on more than 1 cpu-port?), Or define it at switch node level not port level (e.g. via phandle).

If the 5-below-6 way is not the right one i would prefer a driver solution, e.g. let driver choose the best cpu based on fixed value (constant via define) or on highest throughput (trgmii > rgmii),but last may fail if both cpu-ports have same speed like mt7531.

These are the possible solutions i see atm. Maybe dsa people can share their opinion.

>> set master in userspace-config? i remember you've sent a patch adding callback for it.
>
>You can change the DSA master using iproute2-6.1.0 and above with this patch which should be in your inbox as well.
>
>https://lore.kernel.org/netdev/20230211184101.651462-1-richard@routerhints.com/

I try to test it.

>The only issue I see here is that, with this patch series, port5 becomes the default CPU port which is not preferred for the reasons you explained.
>
>So once we can have port6 to be the default CPU port of the DSA slaves, there's no issues left.

For me this would be ok if the current configuration does not change, right :)

Thx for your work.

regards Frank