| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20230301091136.17862-7-r-gunasekaran@ti.com>
Date: Wed, 1 Mar 2023 14:41:34 +0530
From: Ravi Gunasekaran <r-gunasekaran@...com>
To: <nm@...com>, <afd@...com>, <vigneshr@...com>, <kristo@...nel.org>,
<robh+dt@...nel.org>, <krzysztof.kozlowski+dt@...aro.org>,
<s-vadapalli@...com>, <vaishnav.a@...com>, <r-gunasekaran@...com>
CC: <linux-arm-kernel@...ts.infradead.org>,
<devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>
Subject: [PATCH v12 6/8] arm64: dts: ti: k3-j721s2: Add support for OSPI Flashes
From: Aswath Govindraju <a-govindraju@...com>
J721S2 has an OSPI NOR flash on its SOM connected the OSPI0 instance and a
QSPI NOR flash on the common processor board connected to the OSPI1
instance. Add support for the same
Reviewed-by: Vaishnav Achath <vaishnav.a@...com>
Signed-off-by: Aswath Govindraju <a-govindraju@...com>
Signed-off-by: Matt Ranostay <mranostay@...com>
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@...com>
---
Changes from v11:
* Remove deprecated properties
Changes from v10:
* Removed Link tag from commit message
Changes from v9:
* Enabled fss and ospi nodes
Changes from v8:
* No change
Changes from v7:
* No change
Changes from v6:
* No change
Changes from v5:
* Removed Cc tags from commit message
Changes from v4:
* No change
Changes from v3:
* No change
Changes from v2:
* No change
Changes from v1:
* No change
.../dts/ti/k3-j721s2-common-proc-board.dts | 37 +++++++++++++++++
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 41 +++++++++++++++++++
2 files changed, 78 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
index fa38940fe6cd..6bd6370e5bae 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -206,6 +206,20 @@
J721S2_WKUP_IOPAD(0x0c8, PIN_INPUT, 7) /* (C28) WKUP_GPIO0_2 */
>;
};
+
+ mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x040, PIN_OUTPUT, 0) /* (A19) MCU_OSPI1_CLK */
+ J721S2_WKUP_IOPAD(0x05c, PIN_OUTPUT, 0) /* (D20) MCU_OSPI1_CSn0 */
+ J721S2_WKUP_IOPAD(0x060, PIN_OUTPUT, 0) /* (C21) MCU_OSPI1_CSn1 */
+ J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (D21) MCU_OSPI1_D0 */
+ J721S2_WKUP_IOPAD(0x050, PIN_INPUT, 0) /* (G20) MCU_OSPI1_D1 */
+ J721S2_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (C20) MCU_OSPI1_D2 */
+ J721S2_WKUP_IOPAD(0x058, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */
+ J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */
+ J721S2_WKUP_IOPAD(0x044, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */
+ >;
+ };
};
&main_gpio2 {
@@ -347,6 +361,29 @@
maximum-speed = "high-speed";
};
+&fss {
+ status = "okay";
+};
+
+&ospi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
+
+ flash@0{
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <40000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <2>;
+ };
+};
+
&mcu_mcan0 {
status = "okay";
pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index 6930efff8a5a..d473d79c2757 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -39,6 +39,28 @@
};
};
+&wkup_pmx0 {
+ mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */
+ J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */
+ J721S2_WKUP_IOPAD(0x030, PIN_OUTPUT, 0) /* (G17) MCU_OSPI0_CSn1 */
+ J721S2_WKUP_IOPAD(0x038, PIN_OUTPUT, 0) /* (F14) MCU_OSPI0_CSn2 */
+ J721S2_WKUP_IOPAD(0x03c, PIN_OUTPUT, 0) /* (F17) MCU_OSPI0_CSn3 */
+ J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */
+ J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */
+ J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */
+ J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (F18) MCU_OSPI0_D3 */
+ J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (E19) MCU_OSPI0_D4 */
+ J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D5 */
+ J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (F19) MCU_OSPI0_D6 */
+ J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */
+ J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */
+ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
+ >;
+ };
+};
+
&main_pmx0 {
main_i2c0_pins_default: main-i2c0-pins-default {
pinctrl-single,pins = <
@@ -79,3 +101,22 @@
pinctrl-names = "default";
phys = <&transceiver0>;
};
+
+&ospi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <4>;
+ };
+};
--
2.17.1
Powered by blists - more mailing lists