linux-kernel - [PATCH v4 0/9] arm64: dts: qcom: sa8775p-ride: enable relevant QUPv3 IPs

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite for Android: free password hash cracker in your pocket

[<prev] [next>] [thread-next>] [day] [month] [year] [list]

Message-Id: <20230308104009.260451-1-brgl@bgdev.pl>
Date:   Wed,  8 Mar 2023 11:40:00 +0100
From:   Bartosz Golaszewski <brgl@...ev.pl>
To:     Andy Gross <agross@...nel.org>,
        Bjorn Andersson <andersson@...nel.org>,
        Konrad Dybcio <konrad.dybcio@...aro.org>,
        Rob Herring <robh+dt@...nel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>
Cc:     linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
        linux-kernel@...r.kernel.org,
        Bartosz Golaszewski <bartosz.golaszewski@...aro.org>
Subject: [PATCH v4 0/9] arm64: dts: qcom: sa8775p-ride: enable relevant QUPv3 IPs

From: Bartosz Golaszewski <bartosz.golaszewski@...aro.org>

This enables the QUPv3 interfaces that are exposed on the sa8775p-ride
board: I2C, SPI and the Bluetooth and GNSS UART ports.

v3 -> v4:
- use interconnect constants instead of magic numbers where applicable
- pad addresses in reg to 8 digits
- group pins under state nodes for UART

v2 -> v3:
- fix the interrupt number for uart12
- replace underscores with hyphens in DT node names (although make dtbs_check
  does not raise warnings about this)
- rearrange the commits so that they're more fine-grained with separate
  patches for adding nodes to dtsi and enabling them for the board

v1 -> v2:
- uart17 is the Bluetooth port, not GNSS
- add uart12 for GNSS too in that case

Bartosz Golaszewski (9):
  arm64: dts: qcom: sa8775p: add the QUPv3 #2 node
  arm64: dts: qcom: sa8775p-ride: enable QUPv3 #2
  arm64: dts: qcom: sa8775p: add the i2c18 node
  arm64: dts: qcom: sa8775p-ride: enable i2c18
  arm64: dts: qcom: sa8775p: add the spi16 node
  arm64: dts: qcom: sa8775p-ride: enable the SPI node
  arm64: dts: qcom: sa8775p: add high-speed UART nodes
  arm64: dts: qcom: sa8775p-ride: enable the GNSS UART port
  arm64: dts: qcom: sa8775p-ride: enable the BT UART port

 arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 99 +++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sa8775p.dtsi     | 87 ++++++++++++++++++++
 2 files changed, 186 insertions(+)

-- 
2.37.2