| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAKXuJqgAbdALaRdcoSV+sXbGzwm6h54hZtG2rBobcGA9vyu50g@mail.gmail.com>
Date: Thu, 9 Mar 2023 14:07:58 -0600
From: Steev Klimaszewski <steev@...i.org>
To: Johan Hovold <johan@...nel.org>
Cc: "David S. Miller" <davem@...emloft.net>,
Eric Dumazet <edumazet@...gle.com>,
Jakub Kicinski <kuba@...nel.org>,
Paolo Abeni <pabeni@...hat.com>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Andy Gross <agross@...nel.org>,
Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konrad.dybcio@...aro.org>,
Marcel Holtmann <marcel@...tmann.org>,
Johan Hedberg <johan.hedberg@...il.com>,
Luiz Augusto von Dentz <luiz.dentz@...il.com>,
Sven Peter <sven@...npeter.dev>, netdev@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
linux-arm-msm@...r.kernel.org, linux-bluetooth@...r.kernel.org,
Mark Pearson <markpearson@...ovo.com>
Subject: Re: [PATCH v5 4/4] arm64: dts: qcom: thinkpad-x13s: Add bluetooth
On Thu, Mar 9, 2023 at 11:24 AM Johan Hovold <johan@...nel.org> wrote:
>
> On Wed, Feb 08, 2023 at 08:09:16PM -0600, Steev Klimaszewski wrote:
> > The Lenovo Thinkpad X13s has a WCN6855 Bluetooth controller on uart2,
> > add this.
> >
> > Signed-off-by: Steev Klimaszewski <steev@...i.org>
> > Link: https://lore.kernel.org/r/20230207052829.3996-5-steev@kali.org
>
> This link should not be needed.
>
> Also, please update the patch Subject to use the following prefix:
>
> arm64: dts: qcom: sc8280xp-x13s: ...
>
Yeah, that was me screwing up my patch, will make those changes for v6
> > ---
> > Changes since v4:
> > * Address Konrad's review comments.
> >
> > Changes since v3:
> > * Add vreg_s1c
> > * Add regulators and not dead code
> > * Fix commit message changelog
> >
> > Changes since v2:
> > * Remove dead code and add TODO comment
> > * Make dtbs_check happy with the pin definitions
> > .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 76 +++++++++++++++++++
> > 1 file changed, 76 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> > index f936b020a71d..ad20cfb3a830 100644
> > --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> > +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> > @@ -24,6 +24,8 @@ / {
> > aliases {
> > i2c4 = &i2c4;
> > i2c21 = &i2c21;
> > + serial0 = &uart17;
>
> This is an unrelated change that does not belong in this patch.
>
> > + serial1 = &uart2;
> > };
> >
> > wcd938x: audio-codec {
> > @@ -297,6 +299,15 @@ pmc8280c-rpmh-regulators {
> > qcom,pmic-id = "c";
> > vdd-bob-supply = <&vreg_vph_pwr>;
> >
> > + vreg_s1c: smps1 {
> > + regulator-name = "vreg_s1c";
> > + regulator-min-microvolt = <1880000>;
> > + regulator-max-microvolt = <1900000>;
> > + regulator-allowed-modes = <RPMH_REGULATOR_MODE_AUTO>,
> > + <RPMH_REGULATOR_MODE_RET>;
> > + regulator-allow-set-load;
>
> Don't you need to specify initial-mode as well?
>
> > + };
> > +
> > vreg_l1c: ldo1 {
> > regulator-name = "vreg_l1c";
> > regulator-min-microvolt = <1800000>;
> > @@ -712,6 +723,32 @@ &qup0 {
> > status = "okay";
> > };
> >
> > +&uart2 {
> > + pinctrl-0 = <&uart2_state>;
> > + pinctrl-names = "default";
> > +
> > + status = "okay";
> > +
> > + bluetooth {
> > + compatible = "qcom,wcn6855-bt";
> > +
> > + vddio-supply = <&vreg_s10b>;
> > + vddbtcxmx-supply = <&vreg_s12b>;
> > + vddrfacmn-supply = <&vreg_s12b>;
> > + vddrfa0p8-supply = <&vreg_s12b>;
> > + vddrfa1p2-supply = <&vreg_s11b>;
> > + vddrfa1p7-supply = <&vreg_s1c>;
> > +
> > + max-speed = <3200000>;
> > +
> > + enable-gpios = <&tlmm 133 GPIO_ACTIVE_HIGH>;
> > + swctrl-gpios = <&tlmm 132 GPIO_ACTIVE_HIGH>;
> > +
> > + pinctrl-0 = <&bt_en>;
> > + pinctrl-names = "default";
> > + };
> > +};
> > +
> > &qup1 {
> > status = "okay";
> > };
> > @@ -720,6 +757,11 @@ &qup2 {
> > status = "okay";
> > };
> >
> > +&uart17 {
> > + compatible = "qcom,geni-debug-uart";
> > + status = "okay";
> > +};
>
> This bit does not belong here either. We don't have any means of
> accessing the debug uart on the X13s so we should probably just leave it
> disabled.
>
Will drop it (and the above one as well)
> > +
> > &remoteproc_adsp {
> > firmware-name = "qcom/sc8280xp/LENOVO/21BX/qcadsp8280.mbn";
> >
> > @@ -980,6 +1022,19 @@ hastings_reg_en: hastings-reg-en-state {
> > &tlmm {
> > gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
> >
> > + bt_en: bt-en-state {
>
> As you are configuring more than one pin, please rename this as:
>
> bt_default: bt-default-state
>
> > + hstp-sw-ctrl-pins {
> > + pins = "gpio132";
> > + function = "gpio";
>
> You should define the bias configuration as well. I guess we need to
> keep the default pull-down enabled.
>
> > + };
> > +
> > + hstp-bt-en-pins {
> > + pins = "gpio133";
> > + function = "gpio";
> > + drive-strength = <16>;
>
> bias-disable?
>
> > + };
> > + };
> > +
> > edp_reg_en: edp-reg-en-state {
> > pins = "gpio25";
> > function = "gpio";
> > @@ -1001,6 +1056,27 @@ i2c4_default: i2c4-default-state {
> > bias-disable;
> > };
> >
> > + uart2_state: uart2-state {
>
> Rename this one too:
>
> uart2_default: uart2-default-state
>
> > + cts-pins {
> > + pins = "gpio122";
>
> This should be gpio121 (gpio122 is rts).
>
You are right that it should be... however... if I actually set it to
be 121.... bluetooth doesn't actually come up/work?
> > + function = "qup2";
> > + bias-disable;
>
> Don't we need a pull-down on this one to avoid a floating input when the
> module is powered down?
>
Maybe? I don't have access to the schematics or anything so I was
going with the best guess based on what worked by poking and prodding.
Will try this.
> > + };
> > +
> > + rts-tx-pins {
>
> Please split this in two nodes.
>
> > + pins = "gpio122", "gpio123";
> > + function = "qup2";
> > + drive-strength = <2>;
> > + bias-disable;
> > + };
> > +
> > + rx-pins {
> > + pins = "gpio124";
> > + function = "qup2";
> > + bias-pull-up;
> > + };
> > + };
> > +
> > i2c21_default: i2c21-default-state {
> > pins = "gpio81", "gpio82";
> > function = "qup21";
>
> Johan
Powered by blists - more mailing lists