| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20230309085102.120977-12-manivannan.sadhasivam@linaro.org>
Date: Thu, 9 Mar 2023 14:20:56 +0530
From: Manivannan Sadhasivam <manivannan.sadhasivam@...aro.org>
To: andersson@...nel.org, lpieralisi@...nel.org, kw@...ux.com,
krzysztof.kozlowski+dt@...aro.org, robh@...nel.org
Cc: konrad.dybcio@...aro.org, linux-arm-msm@...r.kernel.org,
devicetree@...r.kernel.org, linux-pci@...r.kernel.org,
linux-kernel@...r.kernel.org, quic_srichara@...cinc.com,
Manivannan Sadhasivam <manivannan.sadhasivam@...aro.org>
Subject: [PATCH v2 11/17] PCI: qcom: Use bulk reset APIs for handling resets for IP rev 2.4.0
All the resets are asserted and deasserted at the same time. So the bulk
reset APIs can be used to handle them together. This simplifies the code
a lot.
It should be noted that there were delays in-between the reset asserts and
deasserts. But going by the config used by other revisions, those delays
are not really necessary. So a single delay after all asserts and one after
deasserts is used.
The total number of resets supported is 12 but only ipq4019 is using all of
them.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@...aro.org>
---
drivers/pci/controller/dwc/pcie-qcom.c | 238 ++++---------------------
1 file changed, 30 insertions(+), 208 deletions(-)
diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 8c39fc554a89..ed43e03b972f 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -176,22 +176,13 @@ struct qcom_pcie_resources_2_3_3 {
struct reset_control_bulk_data rst[QCOM_PCIE_2_3_3_MAX_RESETS];
};
-#define QCOM_PCIE_2_4_0_MAX_CLOCKS 4
+#define QCOM_PCIE_2_4_0_MAX_CLOCKS 4
+#define QCOM_PCIE_2_4_0_MAX_RESETS 12
struct qcom_pcie_resources_2_4_0 {
struct clk_bulk_data clks[QCOM_PCIE_2_4_0_MAX_CLOCKS];
int num_clks;
- struct reset_control *axi_m_reset;
- struct reset_control *axi_s_reset;
- struct reset_control *pipe_reset;
- struct reset_control *axi_m_vmid_reset;
- struct reset_control *axi_s_xpu_reset;
- struct reset_control *parf_reset;
- struct reset_control *phy_reset;
- struct reset_control *axi_m_sticky_reset;
- struct reset_control *pipe_sticky_reset;
- struct reset_control *pwr_reset;
- struct reset_control *ahb_reset;
- struct reset_control *phy_ahb_reset;
+ struct reset_control_bulk_data resets[QCOM_PCIE_2_4_0_MAX_RESETS];
+ int num_resets;
};
/* 6 clocks typically, 7 for sm8250 */
@@ -626,65 +617,24 @@ static int qcom_pcie_get_resources_2_4_0(struct qcom_pcie *pcie)
if (ret < 0)
return ret;
- res->axi_m_reset = devm_reset_control_get_exclusive(dev, "axi_m");
- if (IS_ERR(res->axi_m_reset))
- return PTR_ERR(res->axi_m_reset);
-
- res->axi_s_reset = devm_reset_control_get_exclusive(dev, "axi_s");
- if (IS_ERR(res->axi_s_reset))
- return PTR_ERR(res->axi_s_reset);
-
- if (is_ipq) {
- /*
- * These resources relates to the PHY or are secure clocks, but
- * are controlled here for IPQ4019
- */
- res->pipe_reset = devm_reset_control_get_exclusive(dev, "pipe");
- if (IS_ERR(res->pipe_reset))
- return PTR_ERR(res->pipe_reset);
-
- res->axi_m_vmid_reset = devm_reset_control_get_exclusive(dev,
- "axi_m_vmid");
- if (IS_ERR(res->axi_m_vmid_reset))
- return PTR_ERR(res->axi_m_vmid_reset);
-
- res->axi_s_xpu_reset = devm_reset_control_get_exclusive(dev,
- "axi_s_xpu");
- if (IS_ERR(res->axi_s_xpu_reset))
- return PTR_ERR(res->axi_s_xpu_reset);
-
- res->parf_reset = devm_reset_control_get_exclusive(dev, "parf");
- if (IS_ERR(res->parf_reset))
- return PTR_ERR(res->parf_reset);
-
- res->phy_reset = devm_reset_control_get_exclusive(dev, "phy");
- if (IS_ERR(res->phy_reset))
- return PTR_ERR(res->phy_reset);
- }
-
- res->axi_m_sticky_reset = devm_reset_control_get_exclusive(dev,
- "axi_m_sticky");
- if (IS_ERR(res->axi_m_sticky_reset))
- return PTR_ERR(res->axi_m_sticky_reset);
-
- res->pipe_sticky_reset = devm_reset_control_get_exclusive(dev,
- "pipe_sticky");
- if (IS_ERR(res->pipe_sticky_reset))
- return PTR_ERR(res->pipe_sticky_reset);
-
- res->pwr_reset = devm_reset_control_get_exclusive(dev, "pwr");
- if (IS_ERR(res->pwr_reset))
- return PTR_ERR(res->pwr_reset);
-
- res->ahb_reset = devm_reset_control_get_exclusive(dev, "ahb");
- if (IS_ERR(res->ahb_reset))
- return PTR_ERR(res->ahb_reset);
+ res->resets[0].id = "axi_m";
+ res->resets[1].id = "axi_s";
+ res->resets[2].id = "axi_m_sticky";
+ res->resets[3].id = "pipe_sticky";
+ res->resets[4].id = "pwr";
+ res->resets[5].id = "ahb";
+ res->resets[6].id = "pipe";
+ res->resets[7].id = "axi_m_vmid";
+ res->resets[8].id = "axi_s_xpu";
+ res->resets[9].id = "parf";
+ res->resets[10].id = "phy";
+ res->resets[11].id = "phy_ahb";
+
+ res->num_resets = is_ipq ? 12 : 6;
- if (is_ipq) {
- res->phy_ahb_reset = devm_reset_control_get_exclusive(dev, "phy_ahb");
- if (IS_ERR(res->phy_ahb_reset))
- return PTR_ERR(res->phy_ahb_reset);
- }
+ ret = devm_reset_control_bulk_get_exclusive(dev, res->num_resets, res->resets);
+ if (ret < 0)
+ return ret;
return 0;
}
@@ -693,15 +643,7 @@ static void qcom_pcie_deinit_2_4_0(struct qcom_pcie *pcie)
{
struct qcom_pcie_resources_2_4_0 *res = &pcie->res.v2_4_0;
- reset_control_assert(res->axi_m_reset);
- reset_control_assert(res->axi_s_reset);
- reset_control_assert(res->pipe_reset);
- reset_control_assert(res->pipe_sticky_reset);
- reset_control_assert(res->phy_reset);
- reset_control_assert(res->phy_ahb_reset);
- reset_control_assert(res->axi_m_sticky_reset);
- reset_control_assert(res->pwr_reset);
- reset_control_assert(res->ahb_reset);
+ reset_control_bulk_assert(res->num_resets, res->resets);
clk_bulk_disable_unprepare(res->num_clks, res->clks);
}
@@ -712,149 +654,29 @@ static int qcom_pcie_init_2_4_0(struct qcom_pcie *pcie)
struct device *dev = pci->dev;
int ret;
- ret = reset_control_assert(res->axi_m_reset);
- if (ret) {
- dev_err(dev, "cannot assert axi master reset\n");
- return ret;
- }
-
- ret = reset_control_assert(res->axi_s_reset);
- if (ret) {
- dev_err(dev, "cannot assert axi slave reset\n");
- return ret;
- }
-
- usleep_range(10000, 12000);
-
- ret = reset_control_assert(res->pipe_reset);
- if (ret) {
- dev_err(dev, "cannot assert pipe reset\n");
- return ret;
- }
-
- ret = reset_control_assert(res->pipe_sticky_reset);
- if (ret) {
- dev_err(dev, "cannot assert pipe sticky reset\n");
- return ret;
- }
-
- ret = reset_control_assert(res->phy_reset);
- if (ret) {
- dev_err(dev, "cannot assert phy reset\n");
- return ret;
- }
-
- ret = reset_control_assert(res->phy_ahb_reset);
- if (ret) {
- dev_err(dev, "cannot assert phy ahb reset\n");
+ ret = reset_control_bulk_assert(res->num_resets, res->resets);
+ if (ret < 0) {
+ dev_err(dev, "cannot assert resets\n");
return ret;
}
usleep_range(10000, 12000);
- ret = reset_control_assert(res->axi_m_sticky_reset);
- if (ret) {
- dev_err(dev, "cannot assert axi master sticky reset\n");
- return ret;
- }
-
- ret = reset_control_assert(res->pwr_reset);
- if (ret) {
- dev_err(dev, "cannot assert power reset\n");
- return ret;
- }
-
- ret = reset_control_assert(res->ahb_reset);
- if (ret) {
- dev_err(dev, "cannot assert ahb reset\n");
+ ret = reset_control_bulk_deassert(res->num_resets, res->resets);
+ if (ret < 0) {
+ dev_err(dev, "cannot deassert resets\n");
return ret;
}
usleep_range(10000, 12000);
- ret = reset_control_deassert(res->phy_ahb_reset);
+ ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
if (ret) {
- dev_err(dev, "cannot deassert phy ahb reset\n");
+ reset_control_bulk_assert(res->num_resets, res->resets);
return ret;
}
- ret = reset_control_deassert(res->phy_reset);
- if (ret) {
- dev_err(dev, "cannot deassert phy reset\n");
- goto err_rst_phy;
- }
-
- ret = reset_control_deassert(res->pipe_reset);
- if (ret) {
- dev_err(dev, "cannot deassert pipe reset\n");
- goto err_rst_pipe;
- }
-
- ret = reset_control_deassert(res->pipe_sticky_reset);
- if (ret) {
- dev_err(dev, "cannot deassert pipe sticky reset\n");
- goto err_rst_pipe_sticky;
- }
-
- usleep_range(10000, 12000);
-
- ret = reset_control_deassert(res->axi_m_reset);
- if (ret) {
- dev_err(dev, "cannot deassert axi master reset\n");
- goto err_rst_axi_m;
- }
-
- ret = reset_control_deassert(res->axi_m_sticky_reset);
- if (ret) {
- dev_err(dev, "cannot deassert axi master sticky reset\n");
- goto err_rst_axi_m_sticky;
- }
-
- ret = reset_control_deassert(res->axi_s_reset);
- if (ret) {
- dev_err(dev, "cannot deassert axi slave reset\n");
- goto err_rst_axi_s;
- }
-
- ret = reset_control_deassert(res->pwr_reset);
- if (ret) {
- dev_err(dev, "cannot deassert power reset\n");
- goto err_rst_pwr;
- }
-
- ret = reset_control_deassert(res->ahb_reset);
- if (ret) {
- dev_err(dev, "cannot deassert ahb reset\n");
- goto err_rst_ahb;
- }
-
- usleep_range(10000, 12000);
-
- ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
- if (ret)
- goto err_clks;
-
return 0;
-
-err_clks:
- reset_control_assert(res->ahb_reset);
-err_rst_ahb:
- reset_control_assert(res->pwr_reset);
-err_rst_pwr:
- reset_control_assert(res->axi_s_reset);
-err_rst_axi_s:
- reset_control_assert(res->axi_m_sticky_reset);
-err_rst_axi_m_sticky:
- reset_control_assert(res->axi_m_reset);
-err_rst_axi_m:
- reset_control_assert(res->pipe_sticky_reset);
-err_rst_pipe_sticky:
- reset_control_assert(res->pipe_reset);
-err_rst_pipe:
- reset_control_assert(res->phy_reset);
-err_rst_phy:
- reset_control_assert(res->phy_ahb_reset);
- return ret;
}
static int qcom_pcie_post_init_2_4_0(struct qcom_pcie *pcie)
--
2.25.1
Powered by blists - more mailing lists