| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20230310080518.78054-5-lucas.tanure@collabora.com>
Date: Fri, 10 Mar 2023 08:05:15 +0000
From: Lucas Tanure <lucas.tanure@...labora.com>
To: Vinod Koul <vkoul@...nel.org>,
Kishon Vijay Abraham I <kishon@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Heiko Stuebner <heiko@...ech.de>,
Thomas Gleixner <tglx@...utronix.de>,
Marc Zyngier <maz@...nel.org>,
Lorenzo Pieralisi <lpieralisi@...nel.org>,
Krzysztof Wilczynski <kw@...ux.com>,
Bjorn Helgaas <bhelgaas@...gle.com>
Cc: Qu Wenruo <wqu@...e.com>,
Piotr Oniszczuk <piotr.oniszczuk@...il.com>,
Peter Geis <pgwipeout@...il.com>,
Kever Yang <kever.yang@...k-chips.com>,
linux-phy@...ts.infradead.org, devicetree@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org,
linux-rockchip@...ts.infradead.org, linux-kernel@...r.kernel.org,
linux-pci@...r.kernel.org,
Lucas Tanure <lucas.tanure@...labora.com>,
kernel@...labora.com, Andrew Powers-Holmes <aholmes@...om.net>
Subject: [PATCH 4/7] phy: rockchip: Add naneng combo phy support for RK3588
Add support for RK3588 combo phy
This is based on prior work from XiaoDong Huang and
Peter Geis fixing this issue specifically for Rockchip 356x.
Co-developed-by: Andrew Powers-Holmes <aholmes@...om.net>
Signed-off-by: Andrew Powers-Holmes <aholmes@...om.net>
Signed-off-by: Lucas Tanure <lucas.tanure@...labora.com>
---
.../rockchip/phy-rockchip-naneng-combphy.c | 184 ++++++++++++++++++
1 file changed, 184 insertions(+)
diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
index 7b213825fb5d..7b8b001e4f9e 100644
--- a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
+++ b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
@@ -63,6 +63,9 @@
#define PHYREG18 0x44
#define PHYREG18_PLL_LOOP 0x32
+#define PHYREG27 0x6C
+#define PHYREG27_RX_TRIM_RK3588 0x4C
+
#define PHYREG32 0x7C
#define PHYREG32_SSC_MASK GENMASK(7, 4)
#define PHYREG32_SSC_DIR_SHIFT 4
@@ -114,7 +117,10 @@ struct rockchip_combphy_grfcfg {
struct combphy_reg con2_for_sata;
struct combphy_reg con3_for_sata;
struct combphy_reg pipe_con0_for_sata;
+ struct combphy_reg pipe_con1_for_sata;
struct combphy_reg pipe_xpcs_phy_ready;
+ struct combphy_reg pipe_pcie1l0_sel;
+ struct combphy_reg pipe_pcie1l1_sel;
};
struct rockchip_combphy_cfg {
@@ -559,11 +565,189 @@ static const struct rockchip_combphy_cfg rk3568_combphy_cfgs = {
.combphy_cfg = rk3568_combphy_cfg,
};
+static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
+{
+ const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
+ unsigned long rate;
+ u32 val;
+
+ switch (priv->type) {
+ case PHY_TYPE_PCIE:
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
+ rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_pcie1l0_sel, true);
+ rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_pcie1l1_sel, true);
+ break;
+ case PHY_TYPE_USB3:
+ /* Set SSC downward spread spectrum */
+ rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK,
+ PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT,
+ PHYREG32);
+
+ /* Enable adaptive CTLE for USB3.0 Rx. */
+ val = readl(priv->mmio + PHYREG15);
+ val |= PHYREG15_CTLE_EN;
+ writel(val, priv->mmio + PHYREG15);
+
+ /* Set PLL KVCO fine tuning signals. */
+ rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
+ PHYREG33_PLL_KVCO_VALUE << PHYREG33_PLL_KVCO_SHIFT,
+ PHYREG33);
+
+ /* Enable controlling random jitter. */
+ writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+
+ /* Set PLL input clock divider 1/2. */
+ rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK,
+ PHYREG6_PLL_DIV_2 << PHYREG6_PLL_DIV_SHIFT,
+ PHYREG6);
+
+ writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
+ writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->usb_mode_set, true);
+ break;
+ case PHY_TYPE_SATA:
+ /* Enable adaptive CTLE for SATA Rx. */
+ val = readl(priv->mmio + PHYREG15);
+ val |= PHYREG15_CTLE_EN;
+ writel(val, priv->mmio + PHYREG15);
+ /*
+ * Set tx_rterm=50ohm and rx_rterm=44ohm for SATA.
+ * 0: 60ohm, 8: 50ohm 15: 44ohm (by step abort 1ohm)
+ */
+ val = PHYREG7_TX_RTERM_50OHM << PHYREG7_TX_RTERM_SHIFT;
+ val |= PHYREG7_RX_RTERM_44OHM << PHYREG7_RX_RTERM_SHIFT;
+ writel(val, priv->mmio + PHYREG7);
+
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_sata, true);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_sata, true);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_sata, true);
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_sata, true);
+ rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_con0_for_sata, true);
+ rockchip_combphy_param_write(priv->pipe_grf, &cfg->pipe_con1_for_sata, true);
+ break;
+ case PHY_TYPE_SGMII:
+ case PHY_TYPE_QSGMII:
+ default:
+ dev_err(priv->dev, "incompatible PHY type\n");
+ return -EINVAL;
+ }
+
+ rate = clk_get_rate(priv->refclk);
+
+ switch (rate) {
+ case REF_CLOCK_24MHz:
+ if (priv->type == PHY_TYPE_USB3 || priv->type == PHY_TYPE_SATA) {
+ /* Set ssc_cnt[9:0]=0101111101 & 31.5KHz. */
+ val = PHYREG15_SSC_CNT_VALUE << PHYREG15_SSC_CNT_SHIFT;
+ rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK,
+ val, PHYREG15);
+
+ writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+ }
+ break;
+
+ case REF_CLOCK_25MHz:
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_25m, true);
+ break;
+ case REF_CLOCK_100MHz:
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
+ if (priv->type == PHY_TYPE_PCIE) {
+ /* PLL KVCO fine tuning. */
+ val = 4 << PHYREG33_PLL_KVCO_SHIFT;
+ rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
+ val, PHYREG33);
+
+ /* Enable controlling random jitter. */
+ writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+
+ /* Set up rx_trim: PLL LPF C1 85pf R1 1.25kohm */
+ writel(PHYREG27_RX_TRIM_RK3588, priv->mmio + PHYREG27);
+
+ /* Set up su_trim: */
+ writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+ } else if (priv->type == PHY_TYPE_SATA) {
+ /* downward spread spectrum +500ppm */
+ val = PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT;
+ val |= PHYREG32_SSC_OFFSET_500PPM << PHYREG32_SSC_OFFSET_SHIFT;
+ rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
+ }
+ break;
+ default:
+ dev_err(priv->dev, "Unsupported rate: %lu\n", rate);
+ return -EINVAL;
+ }
+
+ if (priv->ext_refclk) {
+ rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
+ if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
+ val = PHYREG13_RESISTER_HIGH_Z << PHYREG13_RESISTER_SHIFT;
+ val |= PHYREG13_CKRCV_AMP0;
+ rockchip_combphy_updatel(priv, PHYREG13_RESISTER_MASK, val, PHYREG13);
+
+ val = readl(priv->mmio + PHYREG14);
+ val |= PHYREG14_CKRCV_AMP1;
+ writel(val, priv->mmio + PHYREG14);
+ }
+ }
+
+ if (priv->enable_ssc) {
+ val = readl(priv->mmio + PHYREG8);
+ val |= PHYREG8_SSC_EN;
+ writel(val, priv->mmio + PHYREG8);
+ }
+
+ return 0;
+}
+
+static const struct rockchip_combphy_grfcfg rk3588_combphy_grfcfgs = {
+ /* pipe-phy-grf */
+ .pcie_mode_set = { 0x0000, 5, 0, 0x00, 0x11 },
+ .usb_mode_set = { 0x0000, 5, 0, 0x00, 0x04 },
+ .pipe_rxterm_set = { 0x0000, 12, 12, 0x00, 0x01 },
+ .pipe_txelec_set = { 0x0004, 1, 1, 0x00, 0x01 },
+ .pipe_txcomp_set = { 0x0004, 4, 4, 0x00, 0x01 },
+ .pipe_clk_25m = { 0x0004, 14, 13, 0x00, 0x01 },
+ .pipe_clk_100m = { 0x0004, 14, 13, 0x00, 0x02 },
+ .pipe_rxterm_sel = { 0x0008, 8, 8, 0x00, 0x01 },
+ .pipe_txelec_sel = { 0x0008, 12, 12, 0x00, 0x01 },
+ .pipe_txcomp_sel = { 0x0008, 15, 15, 0x00, 0x01 },
+ .pipe_clk_ext = { 0x000c, 9, 8, 0x02, 0x01 },
+ .pipe_phy_status = { 0x0034, 6, 6, 0x01, 0x00 },
+ .con0_for_pcie = { 0x0000, 15, 0, 0x00, 0x1000 },
+ .con1_for_pcie = { 0x0004, 15, 0, 0x00, 0x0000 },
+ .con2_for_pcie = { 0x0008, 15, 0, 0x00, 0x0101 },
+ .con3_for_pcie = { 0x000c, 15, 0, 0x00, 0x0200 },
+ .con0_for_sata = { 0x0000, 15, 0, 0x00, 0x0129 },
+ .con1_for_sata = { 0x0004, 15, 0, 0x00, 0x0000 },
+ .con2_for_sata = { 0x0008, 15, 0, 0x00, 0x80c1 },
+ .con3_for_sata = { 0x000c, 15, 0, 0x00, 0x0407 },
+ /* pipe-grf */
+ .pipe_con0_for_sata = { 0x0000, 11, 5, 0x00, 0x22 },
+ .pipe_con1_for_sata = { 0x0000, 2, 0, 0x00, 0x2 },
+ .pipe_pcie1l0_sel = { 0x0100, 0, 0, 0x01, 0x0 },
+ .pipe_pcie1l1_sel = { 0x0100, 1, 1, 0x01, 0x0 },
+};
+
+static const struct rockchip_combphy_cfg rk3588_combphy_cfgs = {
+ .grfcfg = &rk3588_combphy_grfcfgs,
+ .combphy_cfg = rk3588_combphy_cfg,
+};
+
static const struct of_device_id rockchip_combphy_of_match[] = {
{
.compatible = "rockchip,rk3568-naneng-combphy",
.data = &rk3568_combphy_cfgs,
},
+ {
+ .compatible = "rockchip,rk3588-naneng-combphy",
+ .data = &rk3588_combphy_cfgs,
+ },
{ },
};
MODULE_DEVICE_TABLE(of, rockchip_combphy_of_match);
--
2.39.2
Powered by blists - more mailing lists