| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20230316120549.21486-4-rashmi.a@intel.com>
Date: Thu, 16 Mar 2023 17:35:48 +0530
From: rashmi.a@...el.com
To: ulf.hansson@...aro.org, michal.simek@...inx.com,
p.zabel@...gutronix.de, linux-mmc@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org, robh+dt@...nel.org,
krzysztof.kozlowski+dt@...aro.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, vkoul@...nel.org, kishon@...nel.org,
yuancan@...wei.com, andriy.shevchenko@...ux.intel.com,
linux-phy@...ts.infradead.org, mgross@...ux.intel.com
Cc: kris.pan@...ux.intel.com, adrian.hunter@...el.com,
mahesh.r.vaidya@...el.com, nandhini.srikandan@...el.com,
vasavi.v.itha@...el.com, kenchappa.demakkanavar@...el.com,
furong.zhou@...el.com, mallikarjunappa.sangannavar@...el.com,
rashmi.a@...el.com
Subject: [PATCH v2 3/4] phy: intel: Remove Thunder Bay eMMC PHY support
From: "A, Rashmi" <rashmi.a@...el.com>
Remove Thunder Bay specific code as the product got cancelled
and there are no end customers or users.
Signed-off-by: A, Rashmi <rashmi.a@...el.com>
Reviewed-by: Hunter, Adrian <adrian.hunter@...el.com>
---
drivers/phy/intel/Kconfig | 10 -
drivers/phy/intel/Makefile | 1 -
drivers/phy/intel/phy-intel-thunderbay-emmc.c | 509 ------------------
3 files changed, 520 deletions(-)
delete mode 100644 drivers/phy/intel/phy-intel-thunderbay-emmc.c
diff --git a/drivers/phy/intel/Kconfig b/drivers/phy/intel/Kconfig
index 18a3cc5b98c0..ac42bb2fb394 100644
--- a/drivers/phy/intel/Kconfig
+++ b/drivers/phy/intel/Kconfig
@@ -46,13 +46,3 @@ config PHY_INTEL_LGM_EMMC
select GENERIC_PHY
help
Enable this to support the Intel EMMC PHY
-
-config PHY_INTEL_THUNDERBAY_EMMC
- tristate "Intel Thunder Bay eMMC PHY driver"
- depends on OF && (ARCH_THUNDERBAY || COMPILE_TEST)
- select GENERIC_PHY
- help
- This option enables support for Intel Thunder Bay SoC eMMC PHY.
-
- To compile this driver as a module, choose M here: the module
- will be called phy-intel-thunderbay-emmc.ko.
diff --git a/drivers/phy/intel/Makefile b/drivers/phy/intel/Makefile
index b7321d56b0bb..14550981a707 100644
--- a/drivers/phy/intel/Makefile
+++ b/drivers/phy/intel/Makefile
@@ -3,4 +3,3 @@ obj-$(CONFIG_PHY_INTEL_KEEMBAY_EMMC) += phy-intel-keembay-emmc.o
obj-$(CONFIG_PHY_INTEL_KEEMBAY_USB) += phy-intel-keembay-usb.o
obj-$(CONFIG_PHY_INTEL_LGM_COMBO) += phy-intel-lgm-combo.o
obj-$(CONFIG_PHY_INTEL_LGM_EMMC) += phy-intel-lgm-emmc.o
-obj-$(CONFIG_PHY_INTEL_THUNDERBAY_EMMC) += phy-intel-thunderbay-emmc.o
diff --git a/drivers/phy/intel/phy-intel-thunderbay-emmc.c b/drivers/phy/intel/phy-intel-thunderbay-emmc.c
deleted file mode 100644
index 593f6970b81e..000000000000
--- a/drivers/phy/intel/phy-intel-thunderbay-emmc.c
+++ /dev/null
@@ -1,509 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Intel ThunderBay eMMC PHY driver
- *
- * Copyright (C) 2021 Intel Corporation
- *
- */
-
-#include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/iopoll.h>
-#include <linux/module.h>
-#include <linux/of.h>
-#include <linux/phy/phy.h>
-#include <linux/platform_device.h>
-
-/* eMMC/SD/SDIO core/phy configuration registers */
-#define CTRL_CFG_0 0x00
-#define CTRL_CFG_1 0x04
-#define CTRL_PRESET_0 0x08
-#define CTRL_PRESET_1 0x0c
-#define CTRL_PRESET_2 0x10
-#define CTRL_PRESET_3 0x14
-#define CTRL_PRESET_4 0x18
-#define CTRL_CFG_2 0x1c
-#define CTRL_CFG_3 0x20
-#define PHY_CFG_0 0x24
-#define PHY_CFG_1 0x28
-#define PHY_CFG_2 0x2c
-#define PHYBIST_CTRL 0x30
-#define SDHC_STAT3 0x34
-#define PHY_STAT 0x38
-#define PHYBIST_STAT_0 0x3c
-#define PHYBIST_STAT_1 0x40
-#define EMMC_AXI 0x44
-
-/* CTRL_PRESET_3 */
-#define CTRL_PRESET3_MASK GENMASK(31, 0)
-#define CTRL_PRESET3_SHIFT 0
-
-/* CTRL_CFG_0 bit fields */
-#define SUPPORT_HS_MASK BIT(26)
-#define SUPPORT_HS_SHIFT 26
-
-#define SUPPORT_8B_MASK BIT(24)
-#define SUPPORT_8B_SHIFT 24
-
-/* CTRL_CFG_1 bit fields */
-#define SUPPORT_SDR50_MASK BIT(28)
-#define SUPPORT_SDR50_SHIFT 28
-#define SLOT_TYPE_MASK GENMASK(27, 26)
-#define SLOT_TYPE_OFFSET 26
-#define SUPPORT_64B_MASK BIT(24)
-#define SUPPORT_64B_SHIFT 24
-#define SUPPORT_HS400_MASK BIT(2)
-#define SUPPORT_HS400_SHIFT 2
-#define SUPPORT_DDR50_MASK BIT(1)
-#define SUPPORT_DDR50_SHIFT 1
-#define SUPPORT_SDR104_MASK BIT(0)
-#define SUPPORT_SDR104_SHIFT 0
-
-/* PHY_CFG_0 bit fields */
-#define SEL_DLY_TXCLK_MASK BIT(29)
-#define SEL_DLY_TXCLK_SHIFT 29
-#define SEL_DLY_RXCLK_MASK BIT(28)
-#define SEL_DLY_RXCLK_SHIFT 28
-
-#define OTAP_DLY_ENA_MASK BIT(27)
-#define OTAP_DLY_ENA_SHIFT 27
-#define OTAP_DLY_SEL_MASK GENMASK(26, 23)
-#define OTAP_DLY_SEL_SHIFT 23
-#define ITAP_CHG_WIN_MASK BIT(22)
-#define ITAP_CHG_WIN_SHIFT 22
-#define ITAP_DLY_ENA_MASK BIT(21)
-#define ITAP_DLY_ENA_SHIFT 21
-#define ITAP_DLY_SEL_MASK GENMASK(20, 16)
-#define ITAP_DLY_SEL_SHIFT 16
-#define RET_ENB_MASK BIT(15)
-#define RET_ENB_SHIFT 15
-#define RET_EN_MASK BIT(14)
-#define RET_EN_SHIFT 14
-#define DLL_IFF_MASK GENMASK(13, 11)
-#define DLL_IFF_SHIFT 11
-#define DLL_EN_MASK BIT(10)
-#define DLL_EN_SHIFT 10
-#define DLL_TRIM_ICP_MASK GENMASK(9, 6)
-#define DLL_TRIM_ICP_SHIFT 6
-#define RETRIM_EN_MASK BIT(5)
-#define RETRIM_EN_SHIFT 5
-#define RETRIM_MASK BIT(4)
-#define RETRIM_SHIFT 4
-#define DR_TY_MASK GENMASK(3, 1)
-#define DR_TY_SHIFT 1
-#define PWR_DOWN_MASK BIT(0)
-#define PWR_DOWN_SHIFT 0
-
-/* PHY_CFG_1 bit fields */
-#define REN_DAT_MASK GENMASK(19, 12)
-#define REN_DAT_SHIFT 12
-#define REN_CMD_MASK BIT(11)
-#define REN_CMD_SHIFT 11
-#define REN_STRB_MASK BIT(10)
-#define REN_STRB_SHIFT 10
-#define PU_STRB_MASK BIT(20)
-#define PU_STRB_SHIFT 20
-
-/* PHY_CFG_2 bit fields */
-#define CLKBUF_MASK GENMASK(24, 21)
-#define CLKBUF_SHIFT 21
-#define SEL_STRB_MASK GENMASK(20, 13)
-#define SEL_STRB_SHIFT 13
-#define SEL_FREQ_MASK GENMASK(12, 10)
-#define SEL_FREQ_SHIFT 10
-
-/* PHY_STAT bit fields */
-#define CAL_DONE BIT(6)
-#define DLL_RDY BIT(5)
-
-#define OTAP_DLY 0x0
-#define ITAP_DLY 0x0
-#define STRB 0x33
-
-/* From ACS_eMMC51_16nFFC_RO1100_Userguide_v1p0.pdf p17 */
-#define FREQSEL_200M_170M 0x0
-#define FREQSEL_170M_140M 0x1
-#define FREQSEL_140M_110M 0x2
-#define FREQSEL_110M_80M 0x3
-#define FREQSEL_80M_50M 0x4
-#define FREQSEL_275M_250M 0x5
-#define FREQSEL_250M_225M 0x6
-#define FREQSEL_225M_200M 0x7
-
-/* Phy power status */
-#define PHY_UNINITIALIZED 0
-#define PHY_INITIALIZED 1
-
-/*
- * During init(400KHz) phy_settings will be called with 200MHZ clock
- * To avoid incorrectly setting the phy for init(400KHZ) "phy_power_sts" is used.
- * When actual clock is set always phy is powered off once and then powered on.
- * (sdhci_arasan_set_clock). That feature will be used to identify whether the
- * settings are for init phy_power_on or actual clock phy_power_on
- * 0 --> init settings
- * 1 --> actual settings
- */
-
-struct thunderbay_emmc_phy {
- void __iomem *reg_base;
- struct clk *emmcclk;
- int phy_power_sts;
-};
-
-static inline void update_reg(struct thunderbay_emmc_phy *tbh_phy, u32 offset,
- u32 mask, u32 shift, u32 val)
-{
- u32 tmp;
-
- tmp = readl(tbh_phy->reg_base + offset);
- tmp &= ~mask;
- tmp |= val << shift;
- writel(tmp, tbh_phy->reg_base + offset);
-}
-
-static int thunderbay_emmc_phy_power(struct phy *phy, bool power_on)
-{
- struct thunderbay_emmc_phy *tbh_phy = phy_get_drvdata(phy);
- unsigned int freqsel = FREQSEL_200M_170M;
- unsigned long rate;
- static int lock;
- u32 val;
- int ret;
-
- /* Disable DLL */
- rate = clk_get_rate(tbh_phy->emmcclk);
- switch (rate) {
- case 200000000:
- /* lock dll only when it is used, i.e only if SEL_DLY_TXCLK/RXCLK are 0 */
- update_reg(tbh_phy, PHY_CFG_0, DLL_EN_MASK, DLL_EN_SHIFT, 0x0);
- break;
-
- /* dll lock not required for other frequencies */
- case 50000000 ... 52000000:
- case 400000:
- default:
- break;
- }
-
- if (!power_on)
- return 0;
-
- rate = clk_get_rate(tbh_phy->emmcclk);
- switch (rate) {
- case 170000001 ... 200000000:
- freqsel = FREQSEL_200M_170M;
- break;
-
- case 140000001 ... 170000000:
- freqsel = FREQSEL_170M_140M;
- break;
-
- case 110000001 ... 140000000:
- freqsel = FREQSEL_140M_110M;
- break;
-
- case 80000001 ... 110000000:
- freqsel = FREQSEL_110M_80M;
- break;
-
- case 50000000 ... 80000000:
- freqsel = FREQSEL_80M_50M;
- break;
-
- case 250000001 ... 275000000:
- freqsel = FREQSEL_275M_250M;
- break;
-
- case 225000001 ... 250000000:
- freqsel = FREQSEL_250M_225M;
- break;
-
- case 200000001 ... 225000000:
- freqsel = FREQSEL_225M_200M;
- break;
- default:
- break;
- }
- /* Clock rate is checked against upper limit. It may fall low during init */
- if (rate > 200000000)
- dev_warn(&phy->dev, "Unsupported rate: %lu\n", rate);
-
- udelay(5);
-
- if (lock == 0) {
- /* PDB will be done only once per boot */
- update_reg(tbh_phy, PHY_CFG_0, PWR_DOWN_MASK,
- PWR_DOWN_SHIFT, 0x1);
- lock = 1;
- /*
- * According to the user manual, it asks driver to wait 5us for
- * calpad busy trimming. However it is documented that this value is
- * PVT(A.K.A. process, voltage and temperature) relevant, so some
- * failure cases are found which indicates we should be more tolerant
- * to calpad busy trimming.
- */
- ret = readl_poll_timeout(tbh_phy->reg_base + PHY_STAT,
- val, (val & CAL_DONE), 10, 50);
- if (ret) {
- dev_err(&phy->dev, "caldone failed, ret=%d\n", ret);
- return ret;
- }
- }
- rate = clk_get_rate(tbh_phy->emmcclk);
- switch (rate) {
- case 200000000:
- /* Set frequency of the DLL operation */
- update_reg(tbh_phy, PHY_CFG_2, SEL_FREQ_MASK, SEL_FREQ_SHIFT, freqsel);
-
- /* Enable DLL */
- update_reg(tbh_phy, PHY_CFG_0, DLL_EN_MASK, DLL_EN_SHIFT, 0x1);
-
- /*
- * After enabling analog DLL circuits docs say that we need 10.2 us if
- * our source clock is at 50 MHz and that lock time scales linearly
- * with clock speed. If we are powering on the PHY and the card clock
- * is super slow (like 100kHz) this could take as long as 5.1 ms as
- * per the math: 10.2 us * (50000000 Hz / 100000 Hz) => 5.1 ms
- * hopefully we won't be running at 100 kHz, but we should still make
- * sure we wait long enough.
- *
- * NOTE: There appear to be corner cases where the DLL seems to take
- * extra long to lock for reasons that aren't understood. In some
- * extreme cases we've seen it take up to over 10ms (!). We'll be
- * generous and give it 50ms.
- */
- ret = readl_poll_timeout(tbh_phy->reg_base + PHY_STAT,
- val, (val & DLL_RDY), 10, 50 * USEC_PER_MSEC);
- if (ret) {
- dev_err(&phy->dev, "dllrdy failed, ret=%d\n", ret);
- return ret;
- }
- break;
-
- default:
- break;
- }
- return 0;
-}
-
-static int thunderbay_emmc_phy_init(struct phy *phy)
-{
- struct thunderbay_emmc_phy *tbh_phy = phy_get_drvdata(phy);
-
- tbh_phy->emmcclk = clk_get(&phy->dev, "emmcclk");
-
- return PTR_ERR_OR_ZERO(tbh_phy->emmcclk);
-}
-
-static int thunderbay_emmc_phy_exit(struct phy *phy)
-{
- struct thunderbay_emmc_phy *tbh_phy = phy_get_drvdata(phy);
-
- clk_put(tbh_phy->emmcclk);
-
- return 0;
-}
-
-static int thunderbay_emmc_phy_power_on(struct phy *phy)
-{
- struct thunderbay_emmc_phy *tbh_phy = phy_get_drvdata(phy);
- unsigned long rate;
-
- /* Overwrite capability bits configurable in bootloader */
- update_reg(tbh_phy, CTRL_CFG_0,
- SUPPORT_HS_MASK, SUPPORT_HS_SHIFT, 0x1);
- update_reg(tbh_phy, CTRL_CFG_0,
- SUPPORT_8B_MASK, SUPPORT_8B_SHIFT, 0x1);
- update_reg(tbh_phy, CTRL_CFG_1,
- SUPPORT_SDR50_MASK, SUPPORT_SDR50_SHIFT, 0x1);
- update_reg(tbh_phy, CTRL_CFG_1,
- SUPPORT_DDR50_MASK, SUPPORT_DDR50_SHIFT, 0x1);
- update_reg(tbh_phy, CTRL_CFG_1,
- SUPPORT_SDR104_MASK, SUPPORT_SDR104_SHIFT, 0x1);
- update_reg(tbh_phy, CTRL_CFG_1,
- SUPPORT_HS400_MASK, SUPPORT_HS400_SHIFT, 0x1);
- update_reg(tbh_phy, CTRL_CFG_1,
- SUPPORT_64B_MASK, SUPPORT_64B_SHIFT, 0x1);
-
- if (tbh_phy->phy_power_sts == PHY_UNINITIALIZED) {
- /* Indicates initialization, settings for init, same as 400KHZ setting */
- update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_TXCLK_MASK, SEL_DLY_TXCLK_SHIFT, 0x1);
- update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_RXCLK_MASK, SEL_DLY_RXCLK_SHIFT, 0x1);
- update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_ENA_MASK, ITAP_DLY_ENA_SHIFT, 0x0);
- update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_SEL_MASK, ITAP_DLY_SEL_SHIFT, 0x0);
- update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_ENA_MASK, OTAP_DLY_ENA_SHIFT, 0x0);
- update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_SEL_MASK, OTAP_DLY_SEL_SHIFT, 0);
- update_reg(tbh_phy, PHY_CFG_0, DLL_TRIM_ICP_MASK, DLL_TRIM_ICP_SHIFT, 0);
- update_reg(tbh_phy, PHY_CFG_0, DR_TY_MASK, DR_TY_SHIFT, 0x1);
-
- } else if (tbh_phy->phy_power_sts == PHY_INITIALIZED) {
- /* Indicates actual clock setting */
- rate = clk_get_rate(tbh_phy->emmcclk);
- switch (rate) {
- case 200000000:
- update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_TXCLK_MASK,
- SEL_DLY_TXCLK_SHIFT, 0x0);
- update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_RXCLK_MASK,
- SEL_DLY_RXCLK_SHIFT, 0x0);
- update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_ENA_MASK,
- ITAP_DLY_ENA_SHIFT, 0x0);
- update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_SEL_MASK,
- ITAP_DLY_SEL_SHIFT, 0x0);
- update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_ENA_MASK,
- OTAP_DLY_ENA_SHIFT, 0x1);
- update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_SEL_MASK,
- OTAP_DLY_SEL_SHIFT, 2);
- update_reg(tbh_phy, PHY_CFG_0, DLL_TRIM_ICP_MASK,
- DLL_TRIM_ICP_SHIFT, 0x8);
- update_reg(tbh_phy, PHY_CFG_0, DR_TY_MASK,
- DR_TY_SHIFT, 0x1);
- /* For HS400 only */
- update_reg(tbh_phy, PHY_CFG_2, SEL_STRB_MASK,
- SEL_STRB_SHIFT, STRB);
- break;
-
- case 50000000 ... 52000000:
- /* For both HS and DDR52 this setting works */
- update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_TXCLK_MASK,
- SEL_DLY_TXCLK_SHIFT, 0x1);
- update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_RXCLK_MASK,
- SEL_DLY_RXCLK_SHIFT, 0x1);
- update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_ENA_MASK,
- ITAP_DLY_ENA_SHIFT, 0x0);
- update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_SEL_MASK,
- ITAP_DLY_SEL_SHIFT, 0x0);
- update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_ENA_MASK,
- OTAP_DLY_ENA_SHIFT, 0x1);
- update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_SEL_MASK,
- OTAP_DLY_SEL_SHIFT, 4);
- update_reg(tbh_phy, PHY_CFG_0, DLL_TRIM_ICP_MASK,
- DLL_TRIM_ICP_SHIFT, 0x8);
- update_reg(tbh_phy, PHY_CFG_0,
- DR_TY_MASK, DR_TY_SHIFT, 0x1);
- break;
-
- case 400000:
- update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_TXCLK_MASK,
- SEL_DLY_TXCLK_SHIFT, 0x1);
- update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_RXCLK_MASK,
- SEL_DLY_RXCLK_SHIFT, 0x1);
- update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_ENA_MASK,
- ITAP_DLY_ENA_SHIFT, 0x0);
- update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_SEL_MASK,
- ITAP_DLY_SEL_SHIFT, 0x0);
- update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_ENA_MASK,
- OTAP_DLY_ENA_SHIFT, 0x0);
- update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_SEL_MASK,
- OTAP_DLY_SEL_SHIFT, 0);
- update_reg(tbh_phy, PHY_CFG_0, DLL_TRIM_ICP_MASK,
- DLL_TRIM_ICP_SHIFT, 0);
- update_reg(tbh_phy, PHY_CFG_0, DR_TY_MASK, DR_TY_SHIFT, 0x1);
- break;
-
- default:
- update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_TXCLK_MASK,
- SEL_DLY_TXCLK_SHIFT, 0x1);
- update_reg(tbh_phy, PHY_CFG_0, SEL_DLY_RXCLK_MASK,
- SEL_DLY_RXCLK_SHIFT, 0x1);
- update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_ENA_MASK,
- ITAP_DLY_ENA_SHIFT, 0x0);
- update_reg(tbh_phy, PHY_CFG_0, ITAP_DLY_SEL_MASK,
- ITAP_DLY_SEL_SHIFT, 0x0);
- update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_ENA_MASK,
- OTAP_DLY_ENA_SHIFT, 0x1);
- update_reg(tbh_phy, PHY_CFG_0, OTAP_DLY_SEL_MASK,
- OTAP_DLY_SEL_SHIFT, 2);
- update_reg(tbh_phy, PHY_CFG_0, DLL_TRIM_ICP_MASK,
- DLL_TRIM_ICP_SHIFT, 0x8);
- update_reg(tbh_phy, PHY_CFG_0, DR_TY_MASK,
- DR_TY_SHIFT, 0x1);
- break;
- }
- /* Reset, init seq called without phy_power_off, this indicates init seq */
- tbh_phy->phy_power_sts = PHY_UNINITIALIZED;
- }
-
- update_reg(tbh_phy, PHY_CFG_0, RETRIM_EN_MASK, RETRIM_EN_SHIFT, 0x1);
- update_reg(tbh_phy, PHY_CFG_0, RETRIM_MASK, RETRIM_SHIFT, 0x0);
-
- return thunderbay_emmc_phy_power(phy, 1);
-}
-
-static int thunderbay_emmc_phy_power_off(struct phy *phy)
-{
- struct thunderbay_emmc_phy *tbh_phy = phy_get_drvdata(phy);
-
- tbh_phy->phy_power_sts = PHY_INITIALIZED;
-
- return thunderbay_emmc_phy_power(phy, 0);
-}
-
-static const struct phy_ops thunderbay_emmc_phy_ops = {
- .init = thunderbay_emmc_phy_init,
- .exit = thunderbay_emmc_phy_exit,
- .power_on = thunderbay_emmc_phy_power_on,
- .power_off = thunderbay_emmc_phy_power_off,
- .owner = THIS_MODULE,
-};
-
-static const struct of_device_id thunderbay_emmc_phy_of_match[] = {
- { .compatible = "intel,thunderbay-emmc-phy",
- (void *)&thunderbay_emmc_phy_ops },
- {}
-};
-MODULE_DEVICE_TABLE(of, thunderbay_emmc_phy_of_match);
-
-static int thunderbay_emmc_phy_probe(struct platform_device *pdev)
-{
- struct thunderbay_emmc_phy *tbh_phy;
- struct phy_provider *phy_provider;
- struct device *dev = &pdev->dev;
- const struct of_device_id *id;
- struct phy *generic_phy;
- struct resource *res;
-
- if (!dev->of_node)
- return -ENODEV;
-
- tbh_phy = devm_kzalloc(dev, sizeof(*tbh_phy), GFP_KERNEL);
- if (!tbh_phy)
- return -ENOMEM;
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- tbh_phy->reg_base = devm_ioremap_resource(&pdev->dev, res);
- if (IS_ERR(tbh_phy->reg_base))
- return PTR_ERR(tbh_phy->reg_base);
-
- tbh_phy->phy_power_sts = PHY_UNINITIALIZED;
- id = of_match_node(thunderbay_emmc_phy_of_match, pdev->dev.of_node);
- if (!id) {
- dev_err(dev, "failed to get match_node\n");
- return -EINVAL;
- }
-
- generic_phy = devm_phy_create(dev, dev->of_node, id->data);
- if (IS_ERR(generic_phy)) {
- dev_err(dev, "failed to create PHY\n");
- return PTR_ERR(generic_phy);
- }
-
- phy_set_drvdata(generic_phy, tbh_phy);
- phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
-
- return PTR_ERR_OR_ZERO(phy_provider);
-}
-
-static struct platform_driver thunderbay_emmc_phy_driver = {
- .probe = thunderbay_emmc_phy_probe,
- .driver = {
- .name = "thunderbay-emmc-phy",
- .of_match_table = thunderbay_emmc_phy_of_match,
- },
-};
-module_platform_driver(thunderbay_emmc_phy_driver);
-
-MODULE_AUTHOR("Nandhini S <nandhini.srikandan@...el.com>");
-MODULE_AUTHOR("Rashmi A <rashmi.a@...el.com>");
-MODULE_DESCRIPTION("Intel Thunder Bay eMMC PHY driver");
-MODULE_LICENSE("GPL v2");
--
2.17.1
Powered by blists - more mailing lists