| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20230331232039.1407-1-quic_wcheng@quicinc.com>
Date: Fri, 31 Mar 2023 16:20:39 -0700
From: Wesley Cheng <quic_wcheng@...cinc.com>
To: <gregkh@...uxfoundation.org>, <Thinh.Nguyen@...opsys.com>
CC: <linux-kernel@...r.kernel.org>, <linux-usb@...r.kernel.org>,
<quic_jackp@...cinc.com>, <quic_ugoswami@...cinc.com>,
Wesley Cheng <quic_wcheng@...cinc.com>
Subject: [PATCH] usb: dwc3: gadget: Stall and restart EP0 if host is unresponsive
It was observed that there are hosts that may complete pending SETUP
transactions before the stop active transfers and controller halt occurs,
leading to lingering endxfer commands on DEPs on subsequent pullup/gadget
start iterations.
dwc3_gadget_ep_disable name=ep8in flags=0x3009 direction=1
dwc3_gadget_ep_disable name=ep4in flags=1 direction=1
dwc3_gadget_ep_disable name=ep3out flags=1 direction=0
usb_gadget_disconnect deactivated=0 connected=0 ret=0
The sequence shows that the USB gadget disconnect (dwc3_gadget_pullup(0))
routine completed successfully, allowing for the USB gadget to proceed with
a USB gadget connect. However, if this occurs the system runs into an
issue where:
BUG: spinlock already unlocked on CPU
spin_bug+0x0
dwc3_remove_requests+0x278
dwc3_ep0_out_start+0xb0
__dwc3_gadget_start+0x25c
This is due to the pending endxfers, leading to gadget start (w/o lock
held) to execute the remove requests, which will unlock the dwc3 spinlock
as part of giveback.
To mitigate this, resolve the pending endxfers on the pullup disable path
by:
1. Re-locating the SETUP phase check after stop active transfers, since
that is where the DWC3_EP_DELAY_STOP is potentially set. This also allows
for handling of a host that may be unresponsive by using the completion
timeout to trigger the stall and restart for EP0.
2. Do not call gadget stop until the poll for controller halt is
completed. DEVTEN is cleared as part of gadget stop, so the intention to
allow ep0 events to continue while waiting for controller halt is not
happening.
Fixes: c96683798e27 ("usb: dwc3: ep0: Don't prepare beyond Setup stage")
Signed-off-by: Wesley Cheng <quic_wcheng@...cinc.com>
---
drivers/usb/dwc3/gadget.c | 101 ++++++++++++++++++++++----------------
1 file changed, 58 insertions(+), 43 deletions(-)
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 3c63fa97a680..9715de8e99bc 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -139,6 +139,24 @@ int dwc3_gadget_set_link_state(struct dwc3 *dwc, enum dwc3_link_state state)
return -ETIMEDOUT;
}
+static void dwc3_ep0_reset_state(struct dwc3 *dwc)
+{
+ unsigned int dir;
+
+ if (dwc->ep0state != EP0_SETUP_PHASE) {
+ dir = !!dwc->ep0_expect_in;
+ if (dwc->ep0state == EP0_DATA_PHASE)
+ dwc3_ep0_end_control_data(dwc, dwc->eps[dir]);
+ else
+ dwc3_ep0_end_control_data(dwc, dwc->eps[!dir]);
+
+ dwc->eps[0]->trb_enqueue = 0;
+ dwc->eps[1]->trb_enqueue = 0;
+
+ dwc3_ep0_stall_and_restart(dwc);
+ }
+}
+
/**
* dwc3_ep_inc_trb - increment a trb index.
* @index: Pointer to the TRB index to increment.
@@ -2528,29 +2546,17 @@ static int __dwc3_gadget_start(struct dwc3 *dwc);
static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc)
{
unsigned long flags;
+ int ret;
spin_lock_irqsave(&dwc->lock, flags);
dwc->connected = false;
/*
- * Per databook, when we want to stop the gadget, if a control transfer
- * is still in process, complete it and get the core into setup phase.
+ * Attempt to end pending SETUP status phase, and not wait for the
+ * function to do so.
*/
- if (dwc->ep0state != EP0_SETUP_PHASE) {
- int ret;
-
- if (dwc->delayed_status)
- dwc3_ep0_send_delayed_status(dwc);
-
- reinit_completion(&dwc->ep0_in_setup);
-
- spin_unlock_irqrestore(&dwc->lock, flags);
- ret = wait_for_completion_timeout(&dwc->ep0_in_setup,
- msecs_to_jiffies(DWC3_PULL_UP_TIMEOUT));
- spin_lock_irqsave(&dwc->lock, flags);
- if (ret == 0)
- dev_warn(dwc->dev, "timed out waiting for SETUP phase\n");
- }
+ if (dwc->delayed_status)
+ dwc3_ep0_send_delayed_status(dwc);
/*
* In the Synopsys DesignWare Cores USB3 Databook Rev. 3.30a
@@ -2560,9 +2566,28 @@ static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc)
* bit.
*/
dwc3_stop_active_transfers(dwc);
- __dwc3_gadget_stop(dwc);
spin_unlock_irqrestore(&dwc->lock, flags);
+ /*
+ * Per databook, when we want to stop the gadget, if a control transfer
+ * is still in process, complete it and get the core into setup phase.
+ * In case the host is unresponsive to a SETUP transaction, forcefully
+ * stall the transfer, and move back to the SETUP phase, so that any
+ * pending endxfers can be executed.
+ */
+ if (dwc->ep0state != EP0_SETUP_PHASE) {
+ reinit_completion(&dwc->ep0_in_setup);
+
+ ret = wait_for_completion_timeout(&dwc->ep0_in_setup,
+ msecs_to_jiffies(DWC3_PULL_UP_TIMEOUT));
+ if (ret == 0) {
+ dev_warn(dwc->dev, "wait for SETUP phase timed out\n");
+ spin_lock_irqsave(&dwc->lock, flags);
+ dwc3_ep0_reset_state(dwc);
+ spin_unlock_irqrestore(&dwc->lock, flags);
+ }
+ }
+
/*
* Note: if the GEVNTCOUNT indicates events in the event buffer, the
* driver needs to acknowledge them before the controller can halt.
@@ -2570,7 +2595,19 @@ static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc)
* remaining event generated by the controller while polling for
* DSTS.DEVCTLHLT.
*/
- return dwc3_gadget_run_stop(dwc, false, false);
+ ret = dwc3_gadget_run_stop(dwc, false, false);
+
+ /*
+ * Stop the gadget after controller is halted, so that if needed, the
+ * events to update EP0 state can still occur while the run/stop
+ * routine polls for the halted state. DEVTEN is cleared as part of
+ * gadget stop.
+ */
+ spin_lock_irqsave(&dwc->lock, flags);
+ __dwc3_gadget_stop(dwc);
+ spin_unlock_irqrestore(&dwc->lock, flags);
+
+ return ret;
}
static int dwc3_gadget_pullup(struct usb_gadget *g, int is_on)
@@ -3821,16 +3858,7 @@ static void dwc3_gadget_disconnect_interrupt(struct dwc3 *dwc)
dwc->setup_packet_pending = false;
usb_gadget_set_state(dwc->gadget, USB_STATE_NOTATTACHED);
- if (dwc->ep0state != EP0_SETUP_PHASE) {
- unsigned int dir;
-
- dir = !!dwc->ep0_expect_in;
- if (dwc->ep0state == EP0_DATA_PHASE)
- dwc3_ep0_end_control_data(dwc, dwc->eps[dir]);
- else
- dwc3_ep0_end_control_data(dwc, dwc->eps[!dir]);
- dwc3_ep0_stall_and_restart(dwc);
- }
+ dwc3_ep0_reset_state(dwc);
}
static void dwc3_gadget_reset_interrupt(struct dwc3 *dwc)
@@ -3884,20 +3912,7 @@ static void dwc3_gadget_reset_interrupt(struct dwc3 *dwc)
* phase. So ensure that EP0 is in setup phase by issuing a stall
* and restart if EP0 is not in setup phase.
*/
- if (dwc->ep0state != EP0_SETUP_PHASE) {
- unsigned int dir;
-
- dir = !!dwc->ep0_expect_in;
- if (dwc->ep0state == EP0_DATA_PHASE)
- dwc3_ep0_end_control_data(dwc, dwc->eps[dir]);
- else
- dwc3_ep0_end_control_data(dwc, dwc->eps[!dir]);
-
- dwc->eps[0]->trb_enqueue = 0;
- dwc->eps[1]->trb_enqueue = 0;
-
- dwc3_ep0_stall_and_restart(dwc);
- }
+ dwc3_ep0_reset_state(dwc);
/*
* In the Synopsis DesignWare Cores USB3 Databook Rev. 3.30a
Powered by blists - more mailing lists