lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Date:   Wed, 5 Apr 2023 15:21:03 +0100
From:   Lee Jones <lee@...nel.org>
To:     Andre Przywara <andre.przywara@....com>
Cc:     Liam Girdwood <lgirdwood@...il.com>, Chen-Yu Tsai <wens@...e.org>,
        Mark Brown <broonie@...nel.org>,
        Martin Botka <martin.botka@...ainline.org>,
        martin.botka1@...il.com, Shengyu Qu <wiagn233@...look.com>,
        Samuel Holland <samuel@...lland.org>,
        Jernej Skrabec <jernej.skrabec@...il.com>,
        linux-sunxi@...ts.linux.dev, linux-kernel@...r.kernel.org
Subject: Re: [PATCH v10 3/3] regulator: axp20x: Add support for AXP313a
 variant

Mark,

On Sat, 01 Apr 2023, Andre Przywara wrote:

> From: Martin Botka <martin.botka@...ainline.org>
>
> The AXP313a is your typical I2C controlled PMIC, although in a lighter
> fashion compared to the other X-Powers PMICs: it has only three DCDC
> rails, three LDOs, and no battery charging support.
>
> The AXP313a datasheet does not describe a register to change the DCDC
> switching frequency, and talks of it being fixed at 3 MHz. Check that
> the property allowing to change that frequency is absent from the DT,
> and bail out otherwise.
>
> The third LDO, RTCLDO, is fixed, and cannot even be turned on or off,
> programmatically. On top of that, its voltage is customisable (either
> 1.8V or 3.3V), which we cannot describe easily using the existing
> regulator wrapper functions. This should be fixed properly, using
> regulator-{min,max}-microvolt in the DT, but this requires more changes
> to the code. As some other PMICs (AXP2xx, AXP803) seem to paper over the
> same problem as well, we follow suit here and pretend it's a fixed 1.8V
> regulator. A proper fix can follow later. The BSP code seems to ignore
> this regulator altogether.
>
> Describe the AXP313A's voltage settings and switch registers, how the
> voltages are encoded, and connect this to the MFD device via its
> regulator ID.
>
> Signed-off-by: Martin Botka <martin.botka@...ainline.org>
> Signed-off-by: Andre Przywara <andre.przywara@....com>
> ---
>  drivers/regulator/axp20x-regulator.c | 60 ++++++++++++++++++++++++++++
>  1 file changed, 60 insertions(+)

Is this on your radar?

Can I take the other two patches without causing issues?

> diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c
> index d260c442b788d..81f339009df9b 100644
> --- a/drivers/regulator/axp20x-regulator.c
> +++ b/drivers/regulator/axp20x-regulator.c
> @@ -134,6 +134,11 @@
>  #define AXP22X_PWR_OUT_DLDO4_MASK	BIT_MASK(6)
>  #define AXP22X_PWR_OUT_ALDO3_MASK	BIT_MASK(7)
>
> +#define AXP313A_DCDC1_NUM_VOLTAGES	107
> +#define AXP313A_DCDC23_NUM_VOLTAGES	88
> +#define AXP313A_DCDC_V_OUT_MASK		GENMASK(6, 0)
> +#define AXP313A_LDO_V_OUT_MASK		GENMASK(4, 0)
> +
>  #define AXP803_PWR_OUT_DCDC1_MASK	BIT_MASK(0)
>  #define AXP803_PWR_OUT_DCDC2_MASK	BIT_MASK(1)
>  #define AXP803_PWR_OUT_DCDC3_MASK	BIT_MASK(2)
> @@ -638,6 +643,48 @@ static const struct regulator_desc axp22x_drivevbus_regulator = {
>  	.ops		= &axp20x_ops_sw,
>  };
>
> +static const struct linear_range axp313a_dcdc1_ranges[] = {
> +	REGULATOR_LINEAR_RANGE(500000,   0,  70,  10000),
> +	REGULATOR_LINEAR_RANGE(1220000, 71,  87,  20000),
> +	REGULATOR_LINEAR_RANGE(1600000, 88, 106, 100000),
> +};
> +
> +static const struct linear_range axp313a_dcdc2_ranges[] = {
> +	REGULATOR_LINEAR_RANGE(500000,   0, 70, 10000),
> +	REGULATOR_LINEAR_RANGE(1220000, 71, 87, 20000),
> +};
> +
> +/*
> + * This is deviating from the datasheet. The values here are taken from the
> + * BSP driver and have been confirmed by measurements.
> + */
> +static const struct linear_range axp313a_dcdc3_ranges[] = {
> +	REGULATOR_LINEAR_RANGE(500000,   0,  70, 10000),
> +	REGULATOR_LINEAR_RANGE(1220000, 71, 102, 20000),
> +};
> +
> +static const struct regulator_desc axp313a_regulators[] = {
> +	AXP_DESC_RANGES(AXP313A, DCDC1, "dcdc1", "vin1",
> +			axp313a_dcdc1_ranges, AXP313A_DCDC1_NUM_VOLTAGES,
> +			AXP313A_DCDC1_CONRTOL, AXP313A_DCDC_V_OUT_MASK,
> +			AXP313A_OUTPUT_CONTROL, BIT(0)),
> +	AXP_DESC_RANGES(AXP313A, DCDC2, "dcdc2", "vin2",
> +			axp313a_dcdc2_ranges, AXP313A_DCDC23_NUM_VOLTAGES,
> +			AXP313A_DCDC2_CONRTOL, AXP313A_DCDC_V_OUT_MASK,
> +			AXP313A_OUTPUT_CONTROL, BIT(1)),
> +	AXP_DESC_RANGES(AXP313A, DCDC3, "dcdc3", "vin3",
> +			axp313a_dcdc3_ranges, AXP313A_DCDC23_NUM_VOLTAGES,
> +			AXP313A_DCDC3_CONRTOL, AXP313A_DCDC_V_OUT_MASK,
> +			AXP313A_OUTPUT_CONTROL, BIT(2)),
> +	AXP_DESC(AXP313A, ALDO1, "aldo1", "vin1", 500, 3500, 100,
> +		 AXP313A_ALDO1_CONRTOL, AXP313A_LDO_V_OUT_MASK,
> +		 AXP313A_OUTPUT_CONTROL, BIT(3)),
> +	AXP_DESC(AXP313A, DLDO1, "dldo1", "vin1", 500, 3500, 100,
> +		 AXP313A_DLDO1_CONRTOL, AXP313A_LDO_V_OUT_MASK,
> +		 AXP313A_OUTPUT_CONTROL, BIT(4)),
> +	AXP_DESC_FIXED(AXP313A, RTC_LDO, "rtc-ldo", "vin1", 1800),
> +};
> +
>  /* DCDC ranges shared with AXP813 */
>  static const struct linear_range axp803_dcdc234_ranges[] = {
>  	REGULATOR_LINEAR_RANGE(500000,
> @@ -1040,6 +1087,15 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
>  		def = 3000;
>  		step = 150;
>  		break;
> +	case AXP313A_ID:
> +		/* The DCDC PWM frequency seems to be fixed to 3 MHz. */
> +		if (dcdcfreq != 0) {
> +			dev_err(&pdev->dev,
> +				"DCDC frequency on AXP313a is fixed to 3 MHz.\n");
> +			return -EINVAL;
> +		}
> +
> +		return 0;
>  	default:
>  		dev_err(&pdev->dev,
>  			"Setting DCDC frequency for unsupported AXP variant\n");
> @@ -1232,6 +1288,10 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
>  		drivevbus = of_property_read_bool(pdev->dev.parent->of_node,
>  						  "x-powers,drive-vbus-en");
>  		break;
> +	case AXP313A_ID:
> +		regulators = axp313a_regulators;
> +		nregulators = AXP313A_REG_ID_MAX;
> +		break;
>  	case AXP803_ID:
>  		regulators = axp803_regulators;
>  		nregulators = AXP803_REG_ID_MAX;
> --
> 2.35.7
>

--
Lee Jones [李琼斯]

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ