| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20230407104943.5794-4-cniedermaier@dh-electronics.com>
Date: Fri, 7 Apr 2023 12:49:43 +0200
From: Christoph Niedermaier <cniedermaier@...electronics.com>
To: <linux-arm-kernel@...ts.infradead.org>
CC: Christoph Niedermaier <cniedermaier@...electronics.com>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Shawn Guo <shawnguo@...nel.org>, Li Yang <leoyang.li@....com>,
Marek Vasut <marex@...x.de>, Fabio Estevam <festevam@...x.de>,
NXP Linux Team <linux-imx@....com>,
<kernel@...electronics.com>, <devicetree@...r.kernel.org>,
<linux-kernel@...r.kernel.org>
Subject: [PATCH V4 4/4] ARM: dts: imx6ull-dhcor: Add Marantec maveo box
Add support for Marantec maveo box. The system is used to get a
smart conntection to a door drive. It has USB, WiFi, Bluetooth,
Zigbee and NFC interfaces. The core of this system is a soldered
i.MX6ULL DHCOR SoM from DH electronics.
Signed-off-by: Christoph Niedermaier <cniedermaier@...electronics.com>
---
Cc: Rob Herring <robh+dt@...nel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>
Cc: Shawn Guo <shawnguo@...nel.org>
Cc: Li Yang <leoyang.li@....com>
Cc: Marek Vasut <marex@...x.de>
Cc: Fabio Estevam <festevam@...x.de>
Cc: NXP Linux Team <linux-imx@....com>
Cc: kernel@...electronics.com
Cc: devicetree@...r.kernel.org
Cc: linux-kernel@...r.kernel.org
To: linux-arm-kernel@...ts.infradead.org
---
V2: - Correct the vendor prefix
- Change pinconfig of User and Reset button
V3: - Remove /delete-property/ entries from aliases node
V4: - No changes
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6ull-dhcor-maveo-box.dts | 359 ++++++++++++++++++++++++++
2 files changed, 360 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ull-dhcor-maveo-box.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index aa8fb4b7cdcc..58d3334164e2 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -751,6 +751,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ull-dhcom-drc02.dtb \
imx6ull-dhcom-pdk2.dtb \
imx6ull-dhcom-picoitx.dtb \
+ imx6ull-dhcor-maveo-box.dtb \
imx6ull-jozacp.dtb \
imx6ull-kontron-bl.dtb \
imx6ull-myir-mys-6ulx-eval.dtb \
diff --git a/arch/arm/boot/dts/imx6ull-dhcor-maveo-box.dts b/arch/arm/boot/dts/imx6ull-dhcor-maveo-box.dts
new file mode 100644
index 000000000000..047f7b2d8526
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-dhcor-maveo-box.dts
@@ -0,0 +1,359 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2023 DH electronics GmbH
+ * Copyright (C) 2023 Marantec electronics GmbH
+ *
+ * DHCOM iMX6ULL variant:
+ * DHCR-iMX6ULL-C080-R051-SPI-WBT-I-01LG
+ * DHCOR PCB number: 578-200 or newer
+ * maveo box PCB number: 525-200 or newer
+ */
+
+/dts-v1/;
+
+#include "imx6ull-dhcor-som.dtsi"
+
+/ {
+ model = "DH electronics i.MX6ULL DHCOR on maveo box";
+ compatible = "marantec,imx6ull-dhcor-maveo-box", "dh,imx6ull-dhcor-som",
+ "fsl,imx6ull";
+
+ aliases {
+ mmc2 = &usdhc2;
+ spi0 = &ecspi4;
+ spi3 = &ecspi1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+ compatible = "regulator-fixed";
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "usb-otg1-vbus";
+ };
+
+ reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+ compatible = "regulator-fixed";
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "usb-otg2-vbus";
+ };
+
+ /* WiFi pin WL_REG_ON is connected to GPIO 5.9 */
+ usdhc1_pwrseq: usdhc1-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ };
+};
+
+/* BT pin BT_REG_ON is connected to GPIO 1.18 */
+&bluetooth {
+ shutdown-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+};
+
+/* X10 connector */
+&ecspi4 {
+ cs-gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pinctrl_ecspi4>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ spidev@0 {
+ compatible = "dh,dhcom-board";
+ reg = <0>;
+ spi-cpha;
+ spi-cpol;
+ spi-max-frequency = <54000000>;
+ };
+};
+
+&gpio1 {
+ gpio-line-names =
+ "", "", "", "",
+ "", "BUTTON-USER", "", "",
+ "BUTTON-RESET", "", "", "",
+ "", "", "", "",
+ "", "", "BT-REG-ON", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "";
+};
+
+&gpio2 {
+ gpio-line-names =
+ "PSOC-GPIO-1", "", "", "X10-12",
+ "X10-10", "PSOC-GPIO-2", "PSOC-GPIO-3", "",
+ "X10-11", "X10-9", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "";
+};
+
+&gpio3 {
+ gpio-line-names =
+ "DHCOR-HW0", "DHCOR-HW1", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "";
+};
+
+&gpio4 {
+ gpio-line-names =
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "MAVEO-BOX-HW0", "LED-G", "MAVEO-BOX-VAR1",
+ "MAVEO-BOX-VAR0", "MAVEO-BOX-HW1", "MAVEO-BOX-HW2", "LED-B",
+ "LED-R", "", "", "",
+ "", "", "", "";
+};
+
+&gpio5 {
+ gpio-line-names =
+ "PSOC-SWD-IO", "PSOC-SWD-CLK", "PSOC-RESET", "ZIGBEE-PROG",
+ "ZIGBEE-RESET", "", "PSOC-PWR-FAIL-OUT", "NFC-ENABLE",
+ "NFC-IRQ", "WL-REG-ON", "DHCOR-BOOT-M0", "DHCOR-BOOT-M1",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "",
+ "", "", "", "";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ pinctrl-names = "default", "gpio";
+ scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+};
+
+/* Console UART */
+&uart1 {
+ pinctrl-0 = <&pinctrl_uart1>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+/* BT on LGA */
+&uart2 {
+ pinctrl-0 = <&pinctrl_uart2 &pinctrl_bt_gpio>;
+};
+
+/* Zigbee UART */
+&uart3 {
+ pinctrl-0 = <&pinctrl_uart3 &pinctrl_snvs_zigbee_gpio>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usbotg1 {
+ adp-disable;
+ disable-over-current; /* Overcurrent pin isn't connected */
+ dr_mode = "otg";
+ hnp-disable;
+ pinctrl-0 = <&pinctrl_usbotg1>;
+ pinctrl-names = "default";
+ srp-disable;
+ vbus-supply = <®_usb_otg1_vbus>;
+ status = "okay";
+};
+
+&usbotg2 {
+ disable-over-current; /* Overcurrent pin isn't connected */
+ dr_mode = "host";
+ pinctrl-0 = <&pinctrl_usbotg2>;
+ pinctrl-names = "default";
+ tpl-support;
+ vbus-supply = <®_usb_otg2_vbus>;
+ status = "okay";
+};
+
+&usbphy1 {
+ fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+ fsl,tx-d-cal = <106>;
+};
+
+/* WiFi on LGA */
+&usdhc1 {
+ mmc-pwrseq = <&usdhc1_pwrseq>;
+ pinctrl-0 = <&pinctrl_usdhc1_wifi &pinctrl_snvs_wifi_gpio>;
+};
+
+/* eMMC */
+&usdhc2 {
+ bus-width = <8>;
+ no-1-8-v;
+ non-removable;
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-names = "default";
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_3v3>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-0 = <&pinctrl_hog_maveo_box>;
+ pinctrl-names = "default";
+
+ pinctrl_hog_maveo_box: hog-maveo-box-grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO05__GPIO1_IO05 0x120b0 /* BUTTON_USER */
+ MX6UL_PAD_GPIO1_IO08__GPIO1_IO08 0x120b0 /* BUTTON_RESET */
+ MX6UL_PAD_CSI_PIXCLK__GPIO4_IO18 0x400120b0 /* LED_G */
+ MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x400120b0 /* LED_B */
+ MX6UL_PAD_CSI_DATA03__GPIO4_IO24 0x400120b0 /* LED_R */
+ MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09 0x400120b0 /* X10_9 */
+ MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04 0x400120b0 /* X10_10 */
+ MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08 0x400120b0 /* X10_11 */
+ MX6UL_PAD_ENET1_TX_DATA0__GPIO2_IO03 0x400120b0 /* X10_12 */
+ MX6UL_PAD_ENET1_RX_DATA0__GPIO2_IO00 0x400120b0 /* PSOC_GPIO_1 */
+ MX6UL_PAD_ENET1_TX_EN__GPIO2_IO05 0x400120b0 /* PSOC_GPIO_2 */
+ MX6UL_PAD_ENET1_TX_CLK__GPIO2_IO06 0x400120b0 /* PSOC_GPIO_3 */
+ MX6UL_PAD_CSI_MCLK__GPIO4_IO17 0x120b0 /* MAVEO_BOX_HW0 */
+ MX6UL_PAD_CSI_DATA00__GPIO4_IO21 0x120b0 /* MAVEO_BOX_HW1 */
+ MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x120b0 /* MAVEO_BOX_HW2 */
+ MX6UL_PAD_CSI_HSYNC__GPIO4_IO20 0x120b0 /* MAVEO_BOX_VAR0 */
+ MX6UL_PAD_CSI_VSYNC__GPIO4_IO19 0x120b0 /* MAVEO_BOX_VAR1 */
+ MX6UL_PAD_LCD_CLK__GPIO3_IO00 0x120b0 /* DHCOR_HW0 */
+ MX6UL_PAD_LCD_ENABLE__GPIO3_IO01 0x120b0 /* DHCOR_HW1 */
+ MX6UL_PAD_LCD_DATA00__GPIO3_IO05 0x120b0
+ MX6UL_PAD_LCD_DATA01__GPIO3_IO06 0x120b0
+ MX6UL_PAD_LCD_DATA02__GPIO3_IO07 0x120b0
+ MX6UL_PAD_LCD_DATA03__GPIO3_IO08 0x120b0
+ MX6UL_PAD_LCD_DATA04__GPIO3_IO09 0x120b0
+ MX6UL_PAD_LCD_DATA05__GPIO3_IO10 0x120b0
+ MX6UL_PAD_LCD_DATA06__GPIO3_IO11 0x120b0
+ MX6UL_PAD_LCD_DATA07__GPIO3_IO12 0x120b0
+ MX6UL_PAD_LCD_DATA08__GPIO3_IO13 0x120b0
+ MX6UL_PAD_LCD_DATA09__GPIO3_IO14 0x120b0
+ MX6UL_PAD_LCD_DATA10__GPIO3_IO15 0x120b0
+ MX6UL_PAD_LCD_DATA11__GPIO3_IO16 0x120b0
+ MX6UL_PAD_LCD_DATA12__GPIO3_IO17 0x120b0
+ MX6UL_PAD_LCD_DATA13__GPIO3_IO18 0x120b0
+ MX6UL_PAD_LCD_DATA14__GPIO3_IO19 0x120b0
+ MX6UL_PAD_LCD_DATA15__GPIO3_IO20 0x120b0
+ MX6UL_PAD_LCD_DATA16__GPIO3_IO21 0x120b0
+ MX6UL_PAD_LCD_DATA17__GPIO3_IO22 0x120b0
+ MX6UL_PAD_LCD_DATA18__GPIO3_IO23 0x120b0
+ >;
+ };
+
+ pinctrl_bt_gpio: bt-gpio-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x400120b0 /* BT_REG_ON */
+ >;
+ };
+
+ pinctrl_ecspi4: ecspi4-grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_TX_CLK__ECSPI4_MISO 0x100b1
+ MX6UL_PAD_ENET2_TX_EN__ECSPI4_MOSI 0x100b1
+ MX6UL_PAD_ENET2_TX_DATA1__ECSPI4_SCLK 0x100b1
+ MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x1b0b0 /* SS0 */
+ >;
+ };
+
+ pinctrl_i2c2: i2c2-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
+ MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2-gpio-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x4001b8b0
+ MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x4001b8b0
+ >;
+ };
+
+ pinctrl_uart1: uart1-grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3-grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_READY_B__UART3_DCE_TX 0x1b0b1
+ MX6UL_PAD_NAND_CE0_B__UART3_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg1: usbotg1-grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x17059
+ MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x120b0 /* USB_OTG1_PWR */
+ >;
+ };
+
+ pinctrl_usbotg2: usbotg2-grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0x120b0 /* USB_OTG2_PWR */
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2-grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10069
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x17059
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x17059
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x17059
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x17059
+ MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x17059 /* SD2 Reset */
+ >;
+ };
+};
+
+&iomuxc_snvs {
+ pinctrl-0 = <&pinctrl_snvs_hog_maveo_box>;
+ pinctrl-names = "default";
+
+ pinctrl_snvs_hog_maveo_box: snvs-hog-maveo-box-grp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x400120b0 /* PSOC_SWD_IO */
+ MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x400120b0 /* PSOC_SWD_CLK */
+ MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x400120b0 /* PSOC_RESET */
+ MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x400120b0 /* PSOC_PWR_FAIL_OUT */
+ MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x400120b0 /* NFC_ENABLE */
+ MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x400120b0 /* NFC_IRQ */
+ MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10 0x120b0 /* DHCOR_BOOT_M0 */
+ MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11 0x120b0 /* DHCOR_BOOT_M1 */
+ >;
+ };
+
+ pinctrl_snvs_wifi_gpio: snvs-wifi-gpio-grp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x400120b0 /* WL_REG_ON */
+ >;
+ };
+
+ pinctrl_snvs_zigbee_gpio: snvs-zigbee-gpio-grp {
+ fsl,pins = <
+ MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x400120b0 /* ZIGBEE_PROG */
+ MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x400120b0 /* ZIGBEE_RESET */
+ >;
+ };
+};
--
2.11.0
Powered by blists - more mailing lists