| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <87pm8f3ec4.fsf@BL-laptop>
Date: Fri, 07 Apr 2023 17:24:27 +0200
From: Gregory CLEMENT <gregory.clement@...tlin.com>
To: Pali Rohár <pali@...nel.org>,
Andrew Lunn <andrew@...n.ch>, devicetree@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org
Subject: Re: [PATCH V2] arm64: dts: marvell: add DTS for GL.iNet GL-MV1000
Pali Rohár <pali@...nel.org> writes:
> On Thursday 02 February 2023 10:37:06 Enrico Mioso wrote:
>> The GL-MV1000 (Brume) is a small form-factor gateway router.
>> It is based on the Marvell Armada 88F3720 SOC (1GHz), has 3 gigabit ethernet ports, 1 GB RAM, 16M SPI flash, 8GB eMMC and an uSD slot, as well as an USB 2.0 type A and an USB 3.0 type C port.
>>
>> Signed-off-by: Enrico Mioso <mrkiko.rs@...il.com>
>> CC: Pali <pali@...nel.org>
>
> Looks good,
>
> Reviewed-by: Pali Rohár <pali@...nel.org>
Applied on mvebu/dt64
Thanks,
Gregory
>
>> ---
>> arch/arm64/boot/dts/marvell/Makefile | 1 +
>> .../dts/marvell/armada-3720-gl-mv1000.dts | 239 ++++++++++++++++++
>> 2 files changed, 240 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
>>
>> diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
>> index 058237681fe5..79ac09b58a89 100644
>> --- a/arch/arm64/boot/dts/marvell/Makefile
>> +++ b/arch/arm64/boot/dts/marvell/Makefile
>> @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-emmc.dtb
>> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-ultra.dtb
>> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7.dtb
>> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-v7-emmc.dtb
>> +dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-gl-mv1000.dtb
>> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
>> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
>> dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
>> diff --git a/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
>> new file mode 100644
>> index 000000000000..b1b45b4fa9d4
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
>> @@ -0,0 +1,239 @@
>> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
>> +
>> +/dts-v1/;
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/input/input.h>
>> +#include "armada-372x.dtsi"
>> +
>> +/ {
>> + model = "GL.iNet GL-MV1000";
>> + compatible = "glinet,gl-mv1000", "marvell,armada3720";
>> +
>> + aliases {
>> + led-boot = &led_power;
>> + led-failsafe = &led_power;
>> + led-running = &led_power;
>> + led-upgrade = &led_power;
>> + };
>> +
>> + chosen {
>> + stdout-path = "serial0:115200n8";
>> + };
>> +
>> + memory@0 {
>> + device_type = "memory";
>> + reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
>> + };
>> +
>> + vcc_sd_reg1: regulator {
>> + compatible = "regulator-gpio";
>> + regulator-name = "vcc_sd1";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-boot-on;
>> +
>> + gpios-states = <0>;
>> + states = <1800000 0x1
>> + 3300000 0x0>;
>> + enable-active-high;
>> + };
>> +
>> + keys {
>> + compatible = "gpio-keys";
>> +
>> + reset {
>> + label = "reset";
>> + linux,code = <KEY_RESTART>;
>> + gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + switch {
>> + label = "switch";
>> + linux,code = <BTN_0>;
>> + gpios = <&gpiosb 22 GPIO_ACTIVE_LOW>;
>> + };
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> +
>> + vpn {
>> + label = "green:vpn";
>> + gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + wan {
>> + label = "green:wan";
>> + gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
>> + };
>> +
>> + led_power: power {
>> + label = "green:power";
>> + gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
>> + default-state = "on";
>> + };
>> + };
>> +};
>> +
>> +&spi0 {
>> + status = "okay";
>> +
>> + flash@0 {
>> + reg = <0>;
>> + compatible = "jedec,spi-nor";
>> + spi-max-frequency = <104000000>;
>> + m25p,fast-read;
>> + partitions {
>> + compatible = "fixed-partitions";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + partition@0 {
>> + label = "firmware";
>> + reg = <0 0xf0000>;
>> + };
>> +
>> + partition@...00 {
>> + label = "u-boot-env";
>> + reg = <0xf0000 0x8000>;
>> + };
>> +
>> + factory: partition@...00 {
>> + label = "factory";
>> + reg = <0xf8000 0x8000>;
>> + read-only;
>> + };
>> +
>> + partition@...000 {
>> + label = "dtb";
>> + reg = <0x100000 0x10000>;
>> + read-only;
>> + };
>> +
>> + partition@...000 {
>> + label = "rescue";
>> + reg = <0x110000 0x1000000>;
>> + };
>> + };
>> + };
>> +};
>> +
>> +&sdhci1 {
>> + wp-inverted;
>> + bus-width = <4>;
>> + cd-gpios = <&gpionb 17 GPIO_ACTIVE_LOW>;
>> + marvell,pad-type = "sd";
>> + no-1-8-v;
>> + vqmmc-supply = <&vcc_sd_reg1>;
>> + status = "okay";
>> +};
>> +
>> +&sdhci0 {
>> + bus-width = <8>;
>> + mmc-ddr-1_8v;
>> + mmc-hs400-1_8v;
>> + non-removable;
>> + no-sd;
>> + no-sdio;
>> + marvell,pad-type = "fixed-1-8v";
>> + status = "okay";
>> +};
>> +
>> +&usb3 {
>> + status = "okay";
>> +};
>> +
>> +&usb2 {
>> + status = "okay";
>> +};
>> +
>> +&uart0 {
>> + status = "okay";
>> +};
>> +
>> +&mdio {
>> + switch0: switch0@1 {
>> + compatible = "marvell,mv88e6085";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + reg = <1>;
>> +
>> + dsa,member = <0 0>;
>> +
>> + ports: ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port@0 {
>> + reg = <0>;
>> + label = "cpu";
>> + ethernet = <ð0>;
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> + label = "wan";
>> + phy-handle = <&switch0phy0>;
>> + };
>> +
>> + port@2 {
>> + reg = <2>;
>> + label = "lan0";
>> + phy-handle = <&switch0phy1>;
>> +
>> + nvmem-cells = <&macaddr_factory_6>;
>> + nvmem-cell-names = "mac-address";
>> + };
>> +
>> + port@3 {
>> + reg = <3>;
>> + label = "lan1";
>> + phy-handle = <&switch0phy2>;
>> +
>> + nvmem-cells = <&macaddr_factory_6>;
>> + nvmem-cell-names = "mac-address";
>> + };
>> + };
>> +
>> + mdio {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + switch0phy0: switch0phy0@11 {
>> + reg = <0x11>;
>> + };
>> + switch0phy1: switch0phy1@12 {
>> + reg = <0x12>;
>> + };
>> + switch0phy2: switch0phy2@13 {
>> + reg = <0x13>;
>> + };
>> + };
>> + };
>> +};
>> +
>> +ð0 {
>> + nvmem-cells = <&macaddr_factory_0>;
>> + nvmem-cell-names = "mac-address";
>> + phy-mode = "rgmii-id";
>> + status = "okay";
>> +
>> + fixed-link {
>> + speed = <1000>;
>> + full-duplex;
>> + };
>> +};
>> +
>> +&factory {
>> + compatible = "nvmem-cells";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + macaddr_factory_0: macaddr@0 {
>> + reg = <0x0 0x6>;
>> + };
>> +
>> + macaddr_factory_6: macaddr@6 {
>> + reg = <0x6 0x6>;
>> + };
>> +};
>> --
>> 2.39.1
>>
--
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com
Powered by blists - more mailing lists