linux-kernel - [PATCH] tty: serial: fsl_lpuart: use UARTMODIR register bits for lpuart32 platform

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [thread-next>] [day] [month] [year] [list]

Message-Id: <20230413053908.17702-1-sherry.sun@nxp.com>
Date:   Thu, 13 Apr 2023 13:39:08 +0800
From:   Sherry Sun <sherry.sun@....com>
To:     gregkh@...uxfoundation.org, jirislaby@...nel.org,
        philippe.schenker@...adex.com
Cc:     linux-serial@...r.kernel.org, linux-kernel@...r.kernel.org,
        linux-imx@....com
Subject: [PATCH] tty: serial: fsl_lpuart: use UARTMODIR register bits for lpuart32 platform

For lpuart32 platforms, UARTMODIR register is used instead of UARTMODEM.
So here should configure the corresponding UARTMODIR register bits.

Fixes: 67b01837861c ("tty: serial: lpuart: Add RS485 support for 32-bit uart flavour")
Signed-off-by: Sherry Sun <sherry.sun@....com>
---
 drivers/tty/serial/fsl_lpuart.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index 074bfed57fc9..9845d3f5b84b 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -1406,12 +1406,12 @@ static int lpuart32_config_rs485(struct uart_port *port, struct ktermios *termio
 			struct lpuart_port, port);
 
 	unsigned long modem = lpuart32_read(&sport->port, UARTMODIR)
-				& ~(UARTMODEM_TXRTSPOL | UARTMODEM_TXRTSE);
+				& ~(UARTMODIR_TXRTSPOL | UARTMODIR_TXRTSE);
 	lpuart32_write(&sport->port, modem, UARTMODIR);
 
 	if (rs485->flags & SER_RS485_ENABLED) {
 		/* Enable auto RS-485 RTS mode */
-		modem |= UARTMODEM_TXRTSE;
+		modem |= UARTMODIR_TXRTSE;
 
 		/*
 		 * The hardware defaults to RTS logic HIGH while transfer.
@@ -1420,9 +1420,9 @@ static int lpuart32_config_rs485(struct uart_port *port, struct ktermios *termio
 		 * Note: UART is assumed to be active high.
 		 */
 		if (rs485->flags & SER_RS485_RTS_ON_SEND)
-			modem |= UARTMODEM_TXRTSPOL;
+			modem |= UARTMODIR_TXRTSPOL;
 		else if (rs485->flags & SER_RS485_RTS_AFTER_SEND)
-			modem &= ~UARTMODEM_TXRTSPOL;
+			modem &= ~UARTMODIR_TXRTSPOL;
 	}
 
 	lpuart32_write(&sport->port, modem, UARTMODIR);
-- 
2.17.1