Message-ID: <CANCKTBuZ=Hxy9WgnjbauhHqXGx4QU_t8pgX=3che2K89=2BT9A@mail.gmail.com>
Date:   Fri, 14 Apr 2023 08:14:42 -0400
From:   Jim Quinlan <jim2101024@...il.com>
To:     Cyril Brulebois <kibi@...ian.org>
Cc:     linux-pci@...r.kernel.org,
        Nicolas Saenz Julienne <nsaenz@...nel.org>,
        Bjorn Helgaas <bhelgaas@...gle.com>,
        Lorenzo Pieralisi <lorenzo.pieralisi@....com>,
        Phil Elwell <phil@...pberrypi.com>,
        bcm-kernel-feedback-list@...adcom.com, james.quinlan@...adcom.com,
        Florian Fainelli <f.fainelli@...il.com>,
        Lorenzo Pieralisi <lpieralisi@...nel.org>,
        Krzysztof Wilczyński <kw@...ux.com>,
        Rob Herring <robh@...nel.org>,
        "moderated list:BROADCOM BCM2711/BCM2835 ARM ARCHITECTURE" 
        <linux-rpi-kernel@...ts.infradead.org>,
        "moderated list:BROADCOM BCM2711/BCM2835 ARM ARCHITECTURE" 
        <linux-arm-kernel@...ts.infradead.org>,
        open list <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v2 2/3] PCI: brcmstb: CLKREQ# accomodations of downstream device

On Thu, Apr 13, 2023 at 4:06 PM Cyril Brulebois <kibi@...ian.org> wrote:
>
> Hi Jim,
>
> Jim Quinlan <jim2101024@...il.com> (2023-04-13):
> > Can you provide (a) the full boot log prior to applying the patch
> > series and (b) full boot log after applying the series, using an
> > IDENTICAL setup. If it fails on both then it has little to do with my
> > patch series.
>
> Just to be clear, the issue I reported was with:
>  - Raspberry Pi Compute Module 4 (Rev 1.1, 4G RAM, 32G storage)
>  - Raspberry Pi Compute Module 4 IO Board
>  - SupaHub PCIe-to-multiple-USB adapter, reference PCE6U1C-R02, VER 006S
>
> This was my minimal reproducer for the kernel panic at boot-up, which
> goes away with either v1 or v2. When I realized I didn't actually check
> whether the SupaHub board was working correctly, I plugged 2 devices to
> obtain this setup:
>  - Raspberry Pi Compute Module 4 (Rev 1.1, 4G RAM, 32G storage)
>  - Raspberry Pi Compute Module 4 IO Board
>  - SupaHub PCIe-to-multiple-USB adapter, reference PCE6U1C-R02, VER 006S
>  - Kingston DataTraveler G4 32GB on USB-A port #1 of the SupaHub board.
>  - Logitech K120 keyboard on USB-A port #2 of the SupaHub board.
>
> It turns out that this particular revision of the SupaHub board isn't
> supported by xhci_hcd directly (failing to probe with error -110) and
> one needs to enable CONFIG_USB_XHCI_PCI_RENESAS=m and also ship its
> accompanying firmware (/lib/firmware/renesas_usb_fw.mem). With this
> updated kernel config, I'm able to use the keyboard and to read data
> from the memory stick without problems (70 MB/s).
>
> > In my last series your testing somehow conflated the effect of an
> > unrelated MMC interrupt issue so please be precise.
>
> I wish things would be simpler and didn't involve combinatorics, let
> alone other bugs/regressions at times, but I'm really trying my best to
> navigate and report issues and test patches when I can spare some time…

Hi Cyril,

I want to encourage you and others doing testing and bug reporting:
everyone wins when a bug or issue is reported, fixed, and tested.
I'm just asking that when you have negative results, that you provide
information on the "before" and "after" test results of
the patch series, and run both on the same test environment.

Regards,
Jim Quinlan
Broadcom STB

>
>
> In my defence, the very similar board PCE6U1C-R02, VER 006 boots without
> a kernel panic, and works fine with xhci_hcd without that extra module
> and its firmware. It's based on the exact same chip (Renesas Technology
> Corp. uPD720201) though, that's why I didn't realize the need for an
> extra module until now for the PCE6U1C-R02, VER 006S one. (Florian,
> thanks for mentioning .config earlier…)
>
> To sum up, it seems both (sub)versions of that SupaHub PCE6U1C-R02 board
> are usable with this patch series: the kernel panic at boot-up is gone,
> and USB devices plugged into those boards are working as expected.
>
>
> But, speaking of combinatorics, while the patch series helps fix
> https://bugzilla.kernel.org/show_bug.cgi?id=217276 on that particular
> initial combination of CM4 and SupaHub PCE6U1C-R02, VER 006S, it also
> generates a regression if I use a different CM4…
>
> Setup:
>  - Raspberry Pi Compute Module 4 (Rev 1.0, 8G RAM, 32G storage)
>  - Raspberry Pi Compute Module 4 IO Board
>  - SupaHub PCIe-to-multiple-USB adapter, reference PCE6U1C-R02, VER 006S
>
> You'll find attached (a) and (b) as requested above, for this setup, as
> well as the kernel configuration file:
>  - (a) = dmesg-unpatched.txt = boots fine (and USB devices work fine if
>    memory sticks or keyboards are plugged in).
>  - (b) = dmesg-patched.txt = kernel panic.
>  - cm4+pcie.config
>
> I'm getting similar results with the other SupaHub board:
>  - Raspberry Pi Compute Module 4 (Rev 1.0, 8G RAM, 32G storage)
>  - Raspberry Pi Compute Module 4 IO Board
>  - SupaHub PCIe-to-multiple-USB adapter, reference PCE6U1C-R02, VER 006
>
>
> This is probably best summarized this way:
>
>                               | unpatched    | patched
> ------------------------------+--------------+--------------
> CM4 Rev 1.1 4G/32G + VER 006  | OK           | OK
> CM4 Rev 1.1 4G/32G + VER 006S | Kernel panic | OK            ← Bugzilla entry
> CM4 Rev 1.0 8G/32G + VER 006  | OK           | Kernel panic
> CM4 Rev 1.0 8G/32G + VER 006S | OK           | Kernel panic
>
>
> (And I'm of course using the same settings regarding the serial console,
> to get traces when needed.)
>
>
> Cheers,
> --
> Cyril Brulebois (kibi@...ian.org)            <https://debamax.com/>
> D-I release manager -- Release team member -- Freelance Consultant

Powered by blists - more mailing lists