| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-Id: <20230417154832.216774-3-eblanc@baylibre.com>
Date: Mon, 17 Apr 2023 17:48:28 +0200
From: Esteban Blanc <eblanc@...libre.com>
To: nm@...com, vigneshr@...com, kristo@...nel.org, robh+dt@...nel.org,
krzysztof.kozlowski+dt@...aro.org
Cc: linux-arm-kernel@...ts.infradead.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, sterzik@...com, u-kumar1@...com,
eblanc@...libre.com, jneanne@...libre.com, jpanis@...libre.com,
aseketeli@...libre.com
Subject: [PATCH v3 2/6] arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Esteban Blanc <eblanc@...libre.com>
---
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 213 +++++++++++++++++++
1 file changed, 213 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index 6930efff8a5a..9e312c35afdc 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -79,3 +79,216 @@ &main_mcan16 {
pinctrl-names = "default";
phys = <&transceiver0>;
};
+
+&wkup_pmx0 {
+ pmic_irq_pins_default: pmic-irq-pins-default {
+ pinctrl-single,pins = <
+ /* (C21) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+ J721S2_WKUP_IOPAD(0x060, PIN_INPUT, 7)
+ >;
+ };
+
+ wkup_i2c0_pins_default: wkup_i2c0_pins_default {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x100, PIN_INPUT, 0) /* (H24) WKUP_I2C0_SCL */
+ J721S2_WKUP_IOPAD(0x104, PIN_INPUT, 0) /* (H27) WKUP_I2C0_SDA */
+ >;
+ };
+};
+
+&wkup_i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wkup_i2c0_pins_default>;
+ clock-frequency = <400000>;
+
+ tps659411: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ ti,primary-pmic;
+ system-power-controller;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1234-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka1234: buck1234 {
+ regulator-name = "vdd_cpu_avs";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd_mcuwk_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vdd_mcu_gpioret_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ tps659414: pmic@4c {
+ compatible = "ti,tps6594-q1";
+ reg = <0x4c>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1-supply = <&vsys_3v3>;
+ buck2-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ buckb1: buck1 {
+ regulator-name = "vdd_io_1v8_reg";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buckb2: buck2 {
+ regulator-name = "vdd_fpd_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb3: buck3 {
+ regulator-name = "vdd_phy_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb4: buck4 {
+ regulator-name = "vdd_ddr_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb5: buck5 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob1: ldo1 {
+ regulator-name = "vdd_wk_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob2: ldo2 {
+ regulator-name = "vdd_gpioret_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob3: ldo3 {
+ regulator-name = "vda_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob4: ldo4 {
+ regulator-name = "vda_pll_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ lp876411: pmic@58 {
+ compatible = "ti,lp8764-q1";
+ reg = <0x58>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1234-supply = <&vsys_3v3>;
+
+ regulators {
+ buckc1234: buck1234 {
+ regulator-name = "vdd_core_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+};
--
2.39.2
Powered by blists - more mailing lists