| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <a6474ebf-67be-cdd9-8213-6251f27da2bd@arinc9.com>
Date: Mon, 17 Apr 2023 13:42:05 +0300
From: Arınç ÜNAL <arinc.unal@...nc9.com>
To: Johan Hovold <johan@...nel.org>
Cc: Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Bjørn Mork <bjorn@...k.no>, me@...nan.com,
erkin.bozoglu@...ont.com, linux-usb@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: Re: [PATCH] USB: serial: option: add UNISOC vendor and TOZED LT70C
product
On 13.04.2023 18:14, Johan Hovold wrote:
> On Thu, Apr 06, 2023 at 08:50:04AM +0300, arinc9.unal@...il.com wrote:
>> From: Arınç ÜNAL <arinc.unal@...nc9.com>
>>
>> Add UNISOC vendor ID and TOZED LT70-C modem which is based from UNISOC
>> SL8563. The modem supports the NCM mode.
>
> Thanks for the patch. Looks mostly good, but see my comments below.
Thanks a lot for looking at this Johan!
>
>> T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
>> D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
>> P: Vendor=1782 ProdID=4055 Rev=04.04
>> S: Manufacturer=Unisoc Phone
>> S: Product=Unisoc Phone
>> S: SerialNumber=<redacted>
>> C: #Ifs=14 Cfg#= 1 Atr=c0 MxPwr=500mA
>> I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0d Prot=00 Driver=cdc_ncm
>> E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
>> I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_ncm
>> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> I: If#=10 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
>> E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> E: Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> I: If#=11 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
>> E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> E: Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> I: If#=12 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=option
>> E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> E: Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> This looks like an ADB interface which should be blacklisted (reserved)
> so that the driver does not bind to it.
Will do.
>
>> I: If#=13 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
>> E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> I: If#= 2 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0d Prot=00 Driver=cdc_ncm
>> E: Ad=84(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
>> I: If#= 3 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_ncm
>> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> I: If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0d Prot=00 Driver=cdc_ncm
>> E: Ad=86(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
>> I: If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_ncm
>> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> I: If#= 6 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0d Prot=00 Driver=cdc_ncm
>> E: Ad=88(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
>> I: If#= 7 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_ncm
>> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> I: If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
>> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
>> E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>> E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>>
>> Bus 001 Device 002: ID 1782:4055 Unisoc Phone Unisoc Phone
>> Device Descriptor:
>> bLength 18
>> bDescriptorType 1
>> bcdUSB 2.00
>> bDeviceClass 0
>> bDeviceSubClass 0
>> bDeviceProtocol 0
>> bMaxPacketSize0 64
>> idVendor 0x1782
>> idProduct 0x4055
>> bcdDevice 4.04
>> iManufacturer 1 Unisoc Phone
>> iProduct 2 Unisoc Phone
>> iSerial 3 <redacted>
>> bNumConfigurations 1
>
> When resending you can put the verbose lsusb output below the cut-off
> line (---) so that we have it in the mail archives if ever needed.
Will do.
>
> Could you also add something what the various serial interfaces are used
> for?
Me and Conan only know the first interface which is where the AT
commands are run. I will mention this and the ADB interface on v2.
>
>> Signed-off-by: Arınç ÜNAL <arinc.unal@...nc9.com>
>> ---
>>
>> I did not receive any comments on RFC so I'm sending this as is.
>>
>> Arınç
>>
>> ---
>> drivers/usb/serial/option.c | 6 ++++++
>> 1 file changed, 6 insertions(+)
>>
>> diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
>> index f31cc3c76329..65a050a9ca39 100644
>> --- a/drivers/usb/serial/option.c
>> +++ b/drivers/usb/serial/option.c
>> @@ -595,6 +595,11 @@ static void option_instat_callback(struct urb *urb);
>> #define SIERRA_VENDOR_ID 0x1199
>> #define SIERRA_PRODUCT_EM9191 0x90d3
>>
>> +/* UNISOC (Spreadtrum) products */
>> +#define UNISOC_VENDOR_ID 0x1782
>> +/* TOZED TL70-C based on UNISOC SL8563 uses UNISOC's vendor ID */
>> +#define TOZED_PRODUCT_LT70C 0x4055
>> +
>> /* Device flags */
>>
>> /* Highest interface number which can be used with NCTRL() and RSVD() */
>> @@ -2225,6 +2230,7 @@ static const struct usb_device_id option_ids[] = {
>> { USB_DEVICE_AND_INTERFACE_INFO(OPPO_VENDOR_ID, OPPO_PRODUCT_R11, 0xff, 0xff, 0x30) },
>> { USB_DEVICE_AND_INTERFACE_INFO(SIERRA_VENDOR_ID, SIERRA_PRODUCT_EM9191, 0xff, 0xff, 0x30) },
>> { USB_DEVICE_AND_INTERFACE_INFO(SIERRA_VENDOR_ID, SIERRA_PRODUCT_EM9191, 0xff, 0, 0) },
>> + { USB_DEVICE(UNISOC_VENDOR_ID, TOZED_PRODUCT_LT70C) },
>
> You should match also on the interface class so that you don't try to
> bind to the cdc interfaces. See USB_DEVICE_INTERFACE_CLASS() (and
> RSVD() for the ADB interface).
Thanks, the final result should look like this:
{ USB_DEVICE_INTERFACE_CLASS(UNISOC_VENDOR_ID, TOZED_PRODUCT_LT70C, 0xff),
.driver_info = RSVD(12) },
Arınç
Powered by blists - more mailing lists