| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20230421124938.21974-5-quic_devipriy@quicinc.com>
Date: Fri, 21 Apr 2023 18:19:36 +0530
From: Devi Priya <quic_devipriy@...cinc.com>
To: <agross@...nel.org>, <andersson@...nel.org>,
<konrad.dybcio@...aro.org>, <lpieralisi@...nel.org>,
<kw@...ux.com>, <robh@...nel.org>, <bhelgaas@...gle.com>,
<krzysztof.kozlowski+dt@...aro.org>, <mturquette@...libre.com>,
<sboyd@...nel.org>, <mani@...nel.org>,
<linux-arm-msm@...r.kernel.org>, <devicetree@...r.kernel.org>,
<linux-kernel@...r.kernel.org>, <linux-pci@...r.kernel.org>,
<linux-clk@...r.kernel.org>
CC: <quic_srichara@...cinc.com>, <quic_sjaganat@...cinc.com>,
<quic_kathirav@...cinc.com>, <quic_arajkuma@...cinc.com>,
<quic_anusha@...cinc.com>, <quic_ipkumar@...cinc.com>
Subject: [PATCH V3 4/6] arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes
Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
Co-developed-by: Anusha Rao <quic_anusha@...cinc.com>
Signed-off-by: Anusha Rao <quic_anusha@...cinc.com>
Signed-off-by: Devi Priya <quic_devipriy@...cinc.com>
---
Changes in V3:
- Fixed up the PCI I/O port ranges
arch/arm64/boot/dts/qcom/ipq9574.dtsi | 375 +++++++++++++++++++++++++-
1 file changed, 370 insertions(+), 5 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
index e757b57957cf..953a839a1141 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
@@ -6,8 +6,8 @@
* Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
*/
-#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,ipq9574-gcc.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/reset/qcom,ipq9574-gcc.h>
/ {
@@ -116,6 +116,58 @@
#size-cells = <1>;
ranges = <0 0 0 0xffffffff>;
+ pcie0_phy: phy@...00 {
+ compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
+ reg = <0x00084000 0x1000>;
+
+ clocks = <&gcc GCC_PCIE0_AUX_CLK>,
+ <&gcc GCC_PCIE0_AHB_CLK>,
+ <&gcc GCC_ANOC_PCIE0_1LANE_M_CLK>,
+ <&gcc GCC_SNOC_PCIE0_1LANE_S_CLK>,
+ <&gcc GCC_PCIE0_PIPE_CLK>;
+ clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane", "pipe";
+
+ assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
+ assigned-clock-rates = <20000000>;
+
+ resets = <&gcc GCC_PCIE0_PHY_BCR>,
+ <&gcc GCC_PCIE0PHY_PHY_BCR>;
+ reset-names = "phy", "common";
+
+ #clock-cells = <0>;
+ clock-output-names = "gcc_pcie0_pipe_clk_src";
+
+ #phy-cells = <0>;
+ status = "disabled";
+
+ };
+
+ pcie2_phy: phy@...00 {
+ compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+ reg = <0x0008c000 0x2000>;
+
+ clocks = <&gcc GCC_PCIE2_AUX_CLK>,
+ <&gcc GCC_PCIE2_AHB_CLK>,
+ <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
+ <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>,
+ <&gcc GCC_PCIE2_PIPE_CLK>;
+ clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane", "pipe";
+
+ assigned-clocks = <&gcc GCC_PCIE2_AUX_CLK>;
+ assigned-clock-rates = <20000000>;
+
+ resets = <&gcc GCC_PCIE2_PHY_BCR>,
+ <&gcc GCC_PCIE2PHY_PHY_BCR>;
+ reset-names = "phy", "common";
+
+ #clock-cells = <0>;
+ clock-output-names = "gcc_pcie2_pipe_clk_src";
+
+ #phy-cells = <0>;
+ status = "disabled";
+
+ };
+
rng: rng@...00 {
compatible = "qcom,prng-ee";
reg = <0x000e3000 0x1000>;
@@ -123,6 +175,58 @@
clock-names = "core";
};
+ pcie3_phy: phy@...00 {
+ compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
+ reg = <0x000f4000 0x2000>;
+
+ clocks = <&gcc GCC_PCIE3_AUX_CLK>,
+ <&gcc GCC_PCIE3_AHB_CLK>,
+ <&gcc GCC_ANOC_PCIE3_2LANE_M_CLK>,
+ <&gcc GCC_SNOC_PCIE3_2LANE_S_CLK>,
+ <&gcc GCC_PCIE3_PIPE_CLK>;
+ clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane", "pipe";
+
+ assigned-clocks = <&gcc GCC_PCIE3_AUX_CLK>;
+ assigned-clock-rates = <20000000>;
+
+ resets = <&gcc GCC_PCIE3_PHY_BCR>,
+ <&gcc GCC_PCIE3PHY_PHY_BCR>;
+ reset-names = "phy", "common";
+
+ #clock-cells = <0>;
+ clock-output-names = "gcc_pcie3_pipe_clk_src";
+
+ #phy-cells = <0>;
+ status = "disabled";
+
+ };
+
+ pcie1_phy: phy@...00 {
+ compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
+ reg = <0x000fc000 0x1000>;
+
+ clocks = <&gcc GCC_PCIE1_AUX_CLK>,
+ <&gcc GCC_PCIE1_AHB_CLK>,
+ <&gcc GCC_ANOC_PCIE1_1LANE_M_CLK>,
+ <&gcc GCC_SNOC_PCIE1_1LANE_S_CLK>,
+ <&gcc GCC_PCIE1_PIPE_CLK>;
+ clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane", "pipe";
+
+ assigned-clocks = <&gcc GCC_PCIE1_AUX_CLK>;
+ assigned-clock-rates = <20000000>;
+
+ resets = <&gcc GCC_PCIE1_PHY_BCR>,
+ <&gcc GCC_PCIE1PHY_PHY_BCR>;
+ reset-names = "phy", "common";
+
+ #clock-cells = <0>;
+ clock-output-names = "gcc_pcie1_pipe_clk_src";
+
+ #phy-cells = <0>;
+ status = "disabled";
+
+ };
+
tlmm: pinctrl@...0000 {
compatible = "qcom,ipq9574-tlmm";
reg = <0x01000000 0x300000>;
@@ -146,10 +250,10 @@
reg = <0x01800000 0x80000>;
clocks = <&xo_board_clk>,
<&sleep_clk>,
- <0>,
- <0>,
- <0>,
- <0>,
+ <&pcie0_phy>,
+ <&pcie1_phy>,
+ <&pcie2_phy>,
+ <&pcie3_phy>,
<0>;
#clock-cells = <1>;
#reset-cells = <1>;
@@ -478,6 +582,267 @@
status = "disabled";
};
};
+
+ pcie1: pci@...00000 {
+ compatible = "qcom,pcie-ipq9574";
+ reg = <0x10000000 0xf1d>,
+ <0x10000F20 0xa8>,
+ <0x10001000 0x1000>,
+ <0x000F8000 0x4000>,
+ <0x10100000 0x1000>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <2>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x01000000 0x0 0x00000000 0x10200000 0x0 0x100000>, /* I/O */
+ <0x02000000 0x0 0x10300000 0x10300000 0x0 0x7d00000>; /* MEM */
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 35 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 49 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 84 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 85 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "global_irq";
+
+ /* clocks and clock-names are used to enable the clock in CBCR */
+ clocks = <&gcc GCC_PCIE1_AHB_CLK>,
+ <&gcc GCC_PCIE1_AUX_CLK>,
+ <&gcc GCC_PCIE1_AXI_M_CLK>,
+ <&gcc GCC_PCIE1_AXI_S_CLK>,
+ <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>,
+ <&gcc GCC_PCIE1_RCHNG_CLK>;
+ clock-names = "ahb",
+ "aux",
+ "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE1_PIPE_ARES>,
+ <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE1_AXI_S_STICKY_ARES>,
+ <&gcc GCC_PCIE1_AXI_S_ARES>,
+ <&gcc GCC_PCIE1_AXI_M_STICKY_ARES>,
+ <&gcc GCC_PCIE1_AXI_M_ARES>,
+ <&gcc GCC_PCIE1_AUX_ARES>,
+ <&gcc GCC_PCIE1_AHB_ARES>;
+ reset-names = "pipe",
+ "sticky",
+ "axi_s_sticky",
+ "axi_s",
+ "axi_m_sticky",
+ "axi_m",
+ "aux",
+ "ahb";
+
+ phys = <&pcie1_phy>;
+ phy-names = "pciephy";
+ msi-parent = <&v2m0>;
+ status = "disabled";
+ };
+
+ pcie3: pci@...00000 {
+ compatible = "qcom,pcie-ipq9574";
+ reg = <0x18000000 0xf1d>,
+ <0x18000F20 0xa8>,
+ <0x18001000 0x1000>,
+ <0x000F0000 0x4000>,
+ <0x18100000 0x1000>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <4>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <2>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x01000000 0x0 0x00000000 0x18200000 0x0 0x100000>, /* I/O */
+ <0x02000000 0x0 0x18300000 0x18300000 0x0 0x7d00000>; /* MEM */
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 189 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 190 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 191 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 192 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "global_irq";
+
+ /* clocks and clock-names are used to enable the clock in CBCR */
+ clocks = <&gcc GCC_PCIE3_AHB_CLK>,
+ <&gcc GCC_PCIE3_AUX_CLK>,
+ <&gcc GCC_PCIE3_AXI_M_CLK>,
+ <&gcc GCC_PCIE3_AXI_S_CLK>,
+ <&gcc GCC_PCIE3_AXI_S_BRIDGE_CLK>,
+ <&gcc GCC_PCIE3_RCHNG_CLK>;
+ clock-names = "ahb",
+ "aux",
+ "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE3_PIPE_ARES>,
+ <&gcc GCC_PCIE3_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE3_AXI_S_STICKY_ARES>,
+ <&gcc GCC_PCIE3_AXI_S_ARES>,
+ <&gcc GCC_PCIE3_AXI_M_STICKY_ARES>,
+ <&gcc GCC_PCIE3_AXI_M_ARES>,
+ <&gcc GCC_PCIE3_AUX_ARES>,
+ <&gcc GCC_PCIE3_AHB_ARES>;
+ reset-names = "pipe",
+ "sticky",
+ "axi_s_sticky",
+ "axi_s",
+ "axi_m_sticky",
+ "axi_m",
+ "aux",
+ "ahb";
+
+ phys = <&pcie3_phy>;
+ phy-names = "pciephy";
+ msi-parent = <&v2m0>;
+ status = "disabled";
+ };
+
+ pcie2: pci@...00000 {
+ compatible = "qcom,pcie-ipq9574";
+ reg = <0x20000000 0xf1d>,
+ <0x20000F20 0xa8>,
+ <0x20001000 0x1000>,
+ <0x00088000 0x4000>,
+ <0x20100000 0x1000>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <3>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <2>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x01000000 0x0 0x00000000 0x20200000 0x0 0x100000>, /* I/O */
+ <0x02000000 0x0 0x20300000 0x20300000 0x0 0x7d00000>; /* MEM */
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 164 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 165 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 186 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 187 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "global_irq";
+
+ /* clocks and clock-names are used to enable the clock in CBCR */
+ clocks = <&gcc GCC_PCIE2_AHB_CLK>,
+ <&gcc GCC_PCIE2_AUX_CLK>,
+ <&gcc GCC_PCIE2_AXI_M_CLK>,
+ <&gcc GCC_PCIE2_AXI_S_CLK>,
+ <&gcc GCC_PCIE2_AXI_S_BRIDGE_CLK>,
+ <&gcc GCC_PCIE2_RCHNG_CLK>;
+ clock-names = "ahb",
+ "aux",
+ "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE2_PIPE_ARES>,
+ <&gcc GCC_PCIE2_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE2_AXI_S_STICKY_ARES>,
+ <&gcc GCC_PCIE2_AXI_S_ARES>,
+ <&gcc GCC_PCIE2_AXI_M_STICKY_ARES>,
+ <&gcc GCC_PCIE2_AXI_M_ARES>,
+ <&gcc GCC_PCIE2_AUX_ARES>,
+ <&gcc GCC_PCIE2_AHB_ARES>;
+ reset-names = "pipe",
+ "sticky",
+ "axi_s_sticky",
+ "axi_s",
+ "axi_m_sticky",
+ "axi_m",
+ "aux",
+ "ahb";
+
+ phys = <&pcie2_phy>;
+ phy-names = "pciephy";
+ msi-parent = <&v2m0>;
+ status = "disabled";
+ };
+
+ pcie0: pci@...00000 {
+ compatible = "qcom,pcie-ipq9574";
+ reg = <0x28000000 0xf1d>,
+ <0x28000F20 0xa8>,
+ <0x28001000 0x1000>,
+ <0x00080000 0x4000>,
+ <0x28100000 0x1000>;
+ reg-names = "dbi", "elbi", "atu", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <1>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x01000000 0x0 0x00000000 0x28200000 0x0 0x100000>, /* I/O */
+ <0x02000000 0x0 0x28300000 0x28300000 0x0 0x7d00000>; /* MEM */
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 78 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 79 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 83 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "global_irq";
+
+ /* clocks and clock-names are used to enable the clock in CBCR */
+ clocks = <&gcc GCC_PCIE0_AHB_CLK>,
+ <&gcc GCC_PCIE0_AUX_CLK>,
+ <&gcc GCC_PCIE0_AXI_M_CLK>,
+ <&gcc GCC_PCIE0_AXI_S_CLK>,
+ <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
+ <&gcc GCC_PCIE0_RCHNG_CLK>;
+ clock-names = "ahb",
+ "aux",
+ "axi_m",
+ "axi_s",
+ "axi_bridge",
+ "rchng";
+
+ resets = <&gcc GCC_PCIE0_PIPE_ARES>,
+ <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE0_AXI_S_STICKY_ARES>,
+ <&gcc GCC_PCIE0_AXI_S_ARES>,
+ <&gcc GCC_PCIE0_AXI_M_STICKY_ARES>,
+ <&gcc GCC_PCIE0_AXI_M_ARES>,
+ <&gcc GCC_PCIE0_AUX_ARES>,
+ <&gcc GCC_PCIE0_AHB_ARES>;
+ reset-names = "pipe",
+ "sticky",
+ "axi_s_sticky",
+ "axi_s",
+ "axi_m_sticky",
+ "axi_m",
+ "aux",
+ "ahb";
+
+ phys = <&pcie0_phy>;
+ phy-names = "pciephy";
+ msi-parent = <&v2m0>;
+ status = "disabled";
+ };
+
};
timer {
--
2.17.1
Powered by blists - more mailing lists