[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <50c37e0c-3171-bce2-d97e-371150e1854f@quicinc.com>
Date: Thu, 4 May 2023 23:33:44 +0530
From: Krishna Kurapati PSSNV <quic_kriskura@...cinc.com>
To: Konrad Dybcio <konrad.dybcio@...aro.org>,
Thinh Nguyen <Thinh.Nguyen@...opsys.com>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Philipp Zabel <p.zabel@...gutronix.de>,
Andy Gross <agross@...nel.org>,
"Bjorn Andersson" <andersson@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
"Krzysztof Kozlowski" <krzysztof.kozlowski+dt@...aro.org>,
Felipe Balbi <balbi@...nel.org>,
Wesley Cheng <quic_wcheng@...cinc.com>
CC: <linux-usb@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<linux-arm-msm@...r.kernel.org>, <devicetree@...r.kernel.org>,
<quic_pkondeti@...cinc.com>, <quic_ppratap@...cinc.com>,
<quic_jackp@...cinc.com>, <quic_harshq@...cinc.com>,
<ahalaney@...hat.com>, <quic_shazhuss@...cinc.com>
Subject: Re: [PATCH v7 9/9] arm64: dts: qcom: sa8540-ride: Enable first port
of tertiary usb controller
On 5/2/2023 4:37 PM, Konrad Dybcio wrote:
>
>
> On 1.05.2023 16:34, Krishna Kurapati wrote:
>> There is now support for the multiport USB controller this uses so
>> enable it.
>>
>> The board only has a single port hooked up (despite it being wired up to
>> the multiport IP on the SoC). There's also a USB 2.0 mux hooked up,
>> which by default on boot is selected to mux properly. Grab the gpio
>> controlling that and ensure it stays in the right position so USB 2.0
>> continues to be routed from the external port to the SoC.
>>
>> Signed-off-by: Andrew Halaney <ahalaney@...hat.com>
>> Signed-off-by: Krishna Kurapati <quic_kriskura@...cinc.com>
>> ---
> same comments as patch 8
>
> Konrad
Hi Konrad,
Sure, will add a default value for drive-strength for this pinctrl node.
Hi Andrew Halaney,
I currently don't have a Ride device with me to test this change. Can
you help test this patch on SA8540-Ride including (drive-strength =
<2>;) property (which I believe is the default value).
I can test the same on SA8295-ADP and can push the next version quickly.
Regards,
Krishna,
>> arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 22 ++++++++++++++++++++++
>> 1 file changed, 22 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
>> index 24fa449d48a6..53d47593306e 100644
>> --- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
>> +++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
>> @@ -309,6 +309,19 @@ &usb_2_qmpphy0 {
>> status = "okay";
>> };
>>
>> +&usb_2 {
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&usb2_en_state>;
>> +
>> + status = "okay";
>> +};
>> +
>> +&usb_2_dwc3 {
>> + dr_mode = "host";
>> + phy-names = "usb2-port0", "usb3-port0";
>> + phys = <&usb_2_hsphy0>, <&usb_2_qmpphy0>;
>> +};
>> +
>> &xo_board_clk {
>> clock-frequency = <38400000>;
>> };
>> @@ -401,4 +414,13 @@ wake-pins {
>> bias-pull-up;
>> };
>> };
>> +
>> + usb2_en_state: usb2-en-state {
>> + /* TS3USB221A USB2.0 mux select */
>> + pins = "gpio24";
>> + function = "gpio";
>> + drive-strength = <2>;
>> + bias-disable;
>> + output-low;
>> + };
>> };
Powered by blists - more mailing lists