| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Fri, 5 May 2023 03:30:43 +0100
From: Caleb Connolly <caleb.connolly@...aro.org>
To: Dang Huynh <danct12@...eup.net>, Andy Gross <agross@...nel.org>,
Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konrad.dybcio@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>
Cc: linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: Re: [PATCH] arm64: dts: qcom: Add Fxtec Pro1X (QX1050) DTS
On 04/05/2023 21:33, Dang Huynh wrote:
> The F(x)tec Pro1X is a mobile phone released by FX Technologies Ltd
> in 2022.
>
> The phone is exactly the same as the Pro1 released in 2019 with some
> changes:
> - MSM8998 -> SM6115
> - Camera button is no longer multistate
> - Only one 48MP back camera
> - A new keyboard layout picked by the community.
>
> This commit has the following features working:
> - Display (using simplefb)
> - UFS
> - Power and volume buttons
> - Pinctrl
> - RPM Regulators
> - USB (Device Mode)
>
> To get a successful boot run:
>
> cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/\
> sm6115-fxtec-pro1x.dtb > .Image.gz-dtb
>
> mkbootimg --kernel .Image.gz-dtb \
> --ramdisk initrd.img \
> --base 0x0 \
> --kernel_offset 0x8000 \
> --ramdisk_offset 0x1000000 \
> --second_offset 0xf00000 \
> --tags_offset 0x100 \
> --pagesize 4096 \
> --cmdline "CMDLINE HERE" \
> -o qx1050-boot.img
>
> fastboot flash boot qx1050-boot.img
> fastboot erase dtbo
> fastboot reboot
>
> Signed-off-by: Dang Huynh <danct12@...eup.net>
Hi Dang,
Thanks for the patch! I'm glad to see it :D
Just a few minor suggestions from me. Firstly, please can you re-order
the devicetree nodes to be alphabetical. I also left a few comments below.
With these nitpicks fixed:
Reviewed-by: Caleb Connolly <caleb.connolly@...aro.org>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/sm6115-fxtec-pro1x.dts | 252 ++++++++++++++++++++++++
> 2 files changed, 253 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index d42c59572ace..e311ba675f35 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -174,6 +174,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-shift-axolotl.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm850-samsung-w737.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm4250-oneplus-billie2.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sm6115-fxtec-pro1x.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm6115p-lenovo-j606f.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm6125-sony-xperia-seine-pdx201.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sm6125-xiaomi-laurel-sprout.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sm6115-fxtec-pro1x.dts b/arch/arm64/boot/dts/qcom/sm6115-fxtec-pro1x.dts
> new file mode 100644
> index 000000000000..f1d18710d2f0
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sm6115-fxtec-pro1x.dts
> @@ -0,0 +1,252 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2023, Dang Huynh <danct12@...eup.net>
> + */
> +
> +/dts-v1/;
> +
> +#include "sm6115.dtsi"
> +#include "pm6125.dtsi"
> +
> +/ {
> + model = "F(x)tec Pro1 (QX1050)";
> + compatible = "fxtec,pro1x", "qcom,sm6115";
> + chassis-type = "handset";
> +
> + /* required for bootloader to select correct board */
This comment isn't necessary, these two properties are documented in
Documentation/devicetree/bindings/arm/qcom.yaml and are easily searchable.
> + qcom,msm-id = <417 0x10000>, <444 0x10000>;
> + qcom,board-id = <34 0>;
> +
> + aliases {
> + };
I think this node can be dropped if it's empty.
> +
> + chosen {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + framebuffer0: framebuffer@...00000 {
> + compatible = "simple-framebuffer";
> + reg = <0 0x5c000000 0 (1080 * 2160 * 4)>;
> + width = <1080>;
> + height = <2160>;
> + stride = <(1080 * 4)>;
> + format = "a8r8g8b8";
> + clocks = <&gcc GCC_DISP_HF_AXI_CLK>;
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&vol_up_n>;
> +
> + key-volume-up {
> + label = "Volume Up";
> + linux,code = <KEY_VOLUMEUP>;
> + gpios = <&pm6125_gpios 5 GPIO_ACTIVE_LOW>;
> + debounce-interval = <15>;
> + linux,can-disable;
> + gpio-key,wakeup;
> + };
> + };
> +};
> +
> +&tlmm {
> + gpio-reserved-ranges = <0 4>, <14 4>;
> +};
> +
> +&pm6125_gpios {
> + vol_up_n: vol-up-n-state {
> + pins = "gpio5";
> + function = "normal";
> + power-source = <0>;
> + bias-pull-up;
> + input-enable;
> + };
> +};
> +
> +&dispcc {
> + /* HACK: disable until a panel driver is ready to retain simplefb */
> + status = "disabled";
> +};
> +
> +&pon_pwrkey {
> + status = "okay";
> +};
> +
> +&pon_resin {
> + linux,code = <KEY_VOLUMEDOWN>;
> + status = "okay";
> +};
> +
> +&rpm_requests {
> + pm6125-regulators {
> + compatible = "qcom,rpm-pm6125-regulators";
> +
> + vreg_s6a: s6 {
> + regulator-min-microvolt = <304000>;
> + regulator-max-microvolt = <1456000>;
> + };
> +
> + vreg_s7a: s7 {
> + regulator-min-microvolt = <1280000>;
> + regulator-max-microvolt = <2040000>;
> + };
> +
> + vreg_s8a: s8 {
> + regulator-min-microvolt = <1064000>;
> + regulator-max-microvolt = <1304000>;
> + };
> +
> + vreg_l1a: l1 {
> + regulator-min-microvolt = <952000>;
> + regulator-max-microvolt = <1152000>;
> + };
> +
> + vreg_l4a: l4 {
> + regulator-min-microvolt = <488000>;
> + regulator-max-microvolt = <1000000>;
> + };
> +
> + vreg_l5a: l5 {
> + regulator-min-microvolt = <1648000>;
> + regulator-max-microvolt = <3056000>;
> + };
> +
> + vreg_l6a: l6 {
> + regulator-min-microvolt = <576000>;
> + regulator-max-microvolt = <656000>;
> + };
> +
> + vreg_l7a: l7 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1304000>;
> + };
> +
> + vreg_l8a: l8 {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <728000>;
> + };
> +
> + vreg_l9a: l9 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2000000>;
> + };
> +
> + vreg_l10a: l10 {
> + regulator-min-microvolt = <1704000>;
> + regulator-max-microvolt = <1904000>;
> + };
> +
> + vreg_l11a: l11 {
> + regulator-min-microvolt = <1704000>;
> + regulator-max-microvolt = <1952000>;
> + };
> +
> + vreg_l12a: l12 {
> + regulator-min-microvolt = <1624000>;
> + regulator-max-microvolt = <1984000>;
> + };
> +
> + vreg_l13a: l13 {
> + regulator-min-microvolt = <1504000>;
> + regulator-max-microvolt = <1952000>;
> + };
> +
> + vreg_l14a: l14 {
> + regulator-min-microvolt = <1704000>;
> + regulator-max-microvolt = <1904000>;
> + };
> +
> + vreg_l15a: l15 {
> + regulator-min-microvolt = <2920000>;
> + regulator-max-microvolt = <3232000>;
> + };
> +
> + vreg_l16a: l16 {
> + regulator-min-microvolt = <1704000>;
> + regulator-max-microvolt = <1904000>;
> + };
> +
> + vreg_l17a: l17 {
> + regulator-min-microvolt = <1152000>;
> + regulator-max-microvolt = <1384000>;
> + };
> +
> + vreg_l18a: l18 {
> + regulator-min-microvolt = <1104000>;
> + regulator-max-microvolt = <1312000>;
> + };
> +
> + vreg_l19a: l19 {
> + regulator-min-microvolt = <1624000>;
> + regulator-max-microvolt = <3304000>;
> + };
> +
> + vreg_l20a: l20 {
> + regulator-min-microvolt = <1624000>;
> + regulator-max-microvolt = <3304000>;
> + };
> +
> + vreg_l21a: l21 {
> + regulator-min-microvolt = <2400000>;
> + regulator-max-microvolt = <3600000>;
> + };
> +
> + vreg_l22a: l22 {
> + regulator-min-microvolt = <2952000>;
> + regulator-max-microvolt = <3304000>;
> + };
> +
> + vreg_l23a: l23 {
> + regulator-min-microvolt = <3200000>;
> + regulator-max-microvolt = <3400000>;
> + };
> +
> + vreg_l24a: l24 {
> + regulator-min-microvolt = <2704000>;
> + regulator-max-microvolt = <3600000>;
> + };
> + };
> +};
> +
> +&xo_board {
> + clock-frequency = <19200000>;
> +};
> +
> +&sleep_clk {
> + clock-frequency = <32764>;
> +};
> +
> +&ufs_mem_hc {
> + vcc-supply = <&vreg_l24a>;
> + vcc-max-microamp = <600000>;
> + vccq2-supply = <&vreg_l11a>;
> + vccq2-max-microamp = <600000>;
> + status = "okay";
> +};
> +
> +&ufs_mem_phy {
> + vdda-phy-supply = <&vreg_l4a>;
> + vdda-pll-supply = <&vreg_l12a>;
> + vddp-ref-clk-supply = <&vreg_l18a>;
> + status = "okay";
> +};
> +
> +&usb {
> + status = "okay";
> +};
> +
> +&usb_dwc3 {
> + maximum-speed = "high-speed";
> + dr_mode = "peripheral";
> +};
> +
> +&usb_hsphy {
> + vdd-supply = <&vreg_l4a>;
> + vdda-pll-supply = <&vreg_l12a>;
> + vdda-phy-dpdm-supply = <&vreg_l15a>;
> + status = "okay";
> +};
>
> ---
> base-commit: 145e5cddfe8b4bf607510b2dcf630d95f4db420f
> change-id: 20230505-fxtec-pro1x-support-7f782f0480e9
>
> Best regards,
--
Kind Regards,
Caleb (they/them)
Powered by blists - more mailing lists