| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CAAhV-H5j-86EQfw_Ar_Hyu+Kcuuu7wDCLxBKhO20Se48tnRGUg@mail.gmail.com>
Date: Sat, 6 May 2023 11:08:32 +0800
From: Huacai Chen <chenhuacai@...nel.org>
To: Sui Jingfeng <suijingfeng@...ngson.cn>
Cc: Maarten Lankhorst <maarten.lankhorst@...ux.intel.com>,
Maxime Ripard <mripard@...nel.org>,
Thomas Zimmermann <tzimmermann@...e.de>,
David Airlie <airlied@...il.com>,
Daniel Vetter <daniel@...ll.ch>,
Sumit Semwal <sumit.semwal@...aro.org>,
Christian Koenig <christian.koenig@....com>,
Emil Velikov <emil.l.velikov@...il.com>,
linaro-mm-sig@...ts.linaro.org, loongson-kernel@...ts.loongnix.cn,
Li Yi <liyi@...ngson.cn>, linux-kernel@...r.kernel.org,
dri-devel@...ts.freedesktop.org, nathan@...nel.org,
linux-media@...r.kernel.org
Subject: Re: [PATCH v12 2/2] drm: add kms driver for loongson display controller
Hi, Jingfeng,
On Thu, May 4, 2023 at 4:04 PM Sui Jingfeng <suijingfeng@...ngson.cn> wrote:
>
> Loongson display controller IP has been integrated in both Loongson north
> bridge chipset(ls7a1000/ls7a2000) and Loongson SoCs(ls2k1000/ls2k2000), it
> has been even included in Loongson self-made BMC products.
>
> This display controller is a PCI device. It has two display pipes and each
> display pipe support a primary plane and a cursor plane. For the DC in the
> ls7a1000 and ls2k1000, each display pipe has a DVO output interface which
> provide RGB888 signals, vertical & horizontal synchronisations and pixel
> clock. Each CRTC is able to support 1920x1080@...z, the maximum resolution
> of each display pipe is 2048x2048 according to the hardware spec.
>
> For the DC in LS7A2000, each display pipe is equipped with a built-in HDMI
> encoder which is compliant with the HDMI 1.4 specification, thus it support
> 3840x2160@...z. The first display pipe is also equipped with a transparent
> vga encoder which is parallel with the HDMI encoder. The DC in LS7A2000 is
> more complete compare with the one in old chips, besides above feature, it
> has two hardware cursors, two hardware vblank counter and two scanout
> position recorders unit. It also support tiled framebuffer format which
> can be scanout the tiled framebuffer rendered by the LoongGPU directly.
>
> v1 -> v2:
> 1) Use hpd status reg when polling for ls7a2000
> 2) Fix all warnings emerged when compile with W=1
>
> v2 -> v3:
> 1) Add COMPILE_TEST in Kconfig and make the driver off by default
> 2) Alphabetical sorting headers (Thomas)
> 3) Untangle register access functions as much as possible (Thomas)
> 4) Switch to TTM based memory manager and prefer cached mapping
> for Loongson SoC (Thomas)
> 5) Add chip id detection method, now all models are distinguishable.
> 6) Revise builtin HDMI phy driver, nearly all main stream mode
> below 4K@...z is tested, this driver supported these mode very
> well including clone display mode and extend display mode.
>
> v3 -> v4:
> 1) Quickly fix a small mistake.
>
> v4 -> v5:
> 1) Drop potential support for Loongson 2K series SoC temporary,
> this part should be resend with the DT binding patch in the future.
> 2) Add per display pipe debugfs support to the builtin HDMI encoder.
> 3) Rewrite atomic_update() for hardware cursors plane(Thomas)
> 4) Rewrite encoder and connector initialization part, untangle it
> according to the chip(Thomas).
>
> v5 -> v6:
> 1) Remove stray code which didn't get used, say lsdc_of_get_reserved_ram
> 2) Fix all typos I could found, make sentences and code more readable
> 3) Untangle lsdc_hdmi*_connector_detect() function according to the pipe
> 4) After a serious consideration, we rename this driver as loongson.
> Because we also have drivers toward the LoongGPU IP in LS7A2000 and
> LS2K2000. Besides, there are also drivers about the external encoder,
> HDMI audio driver and vbios support etc. This patch only provide DC
> driver part, my teammate Li Yi believe that loongson will be more
> suitable for loongson graphics than lsdc in the long run.
>
> loongson.ko = LSDC + LoongGPU + encoders driver + vbios/DT ...
>
> v6 -> v7:
> 1) Add prime support, self-sharing is works. sharing buffer with etnaviv
> is also tested, and its works with limitation.
> 2) Implement buffer objects tracking with list_head.
> 3) S3(sleep to RAM) is tested on ls3a5000+ls7a2000 evb and it works.
> 4) Rewrite lsdc_bo_move, since ttm core stop allocating resources
> during BO creation. Patch V1 ~ V6 of this series no longer works
> on latest kernel. Thus, we send V7 to revival them.
>
> v7 -> v8:
> 1) Zero a compile warnnings on 32-bit platform, compile with W=1
> 2) Revise lsdc_bo_gpu_offset() and minor cleanup
> 3) Pageflip tested on the virtual terminal with following commands
>
> modetest -M loongson -s 32:1920x1080 -v
> modetest -M loongson -s 34:1920x1080 -v -F tiles
>
> It works like a charm, when running pageflip test with dual screnn
> configuration, another two additional bo created by the modetest
> emerged, VRAM usage up to 40+MB, well we have at least 64MB, still
> enough.
>
> # cat bos
>
> bo[0000]: size: 8112kB VRAM
> bo[0001]: size: 16kB VRAM
> bo[0002]: size: 16kB VRAM
> bo[0003]: size: 16208kB VRAM
> bo[0004]: size: 8112kB VRAM
> bo[0005]: size: 8112kB VRAM
>
> v8 -> v9:
> 1) Select I2C and I2C_ALGOBIT in Kconfig and should depend on MMU.
> 2) Using pci_get_domain_bus_and_slot to get the GPU device.
> 3) Other minor improvements.
>
> Those patches are tested on ls3a5000 + ls7a1000 CRB, ls3a5000 + ls7a2000
> evb, and lemote a1901 board(ls3a4000 + ls7a1000). On loongson mips CPU,
> the write combine support should be enabled, to get a decent performance
> for writing framebuffer data to the VRAM.
>
> v9 -> v10:
> 1) Revise lsdc_drm_freeze() to implement S3 completely and correctly.
> I suddenly realized that pinned buffer can not move and VRAM lost
> power when sleep to RAM. Thus, the data in the buffer who is pinned
> in VRAM will get lost when resume. Yet it's not big problem because
> we are software rendering solution which relay on the CPU update the
> front framebuffer. We can see the garbage data when resume from S3,
> but the screen will show correct image as I move the cursor. This is
> due to the cpu repaint. v10 of this patch make S3 perfect by unpin
> all of BOs in VRAM, evict them all to system RAM.
>
> v10 -> v11:
> 1) On double screen case, the single giant framebuffer is referenced by
> two GEM object, hence, it will be pinned by prepare_fb() at lease two
> times. This cause its pin count > 1. V10 of this patch only unpin VRAM
> BOs once when suspend, which is not correct on double screen case. V11
> of this patch unpin BOs until its pin count reach to zero when suspend.
> Then, we make the S3 support complete finally. With v11, I can't see
> any garbage data after resume. Teste on both ls7a1000 and ls7a2000
> platform, with single screen and double screen configuration tested.
> 2) Fix vblank wait timeout when disable CRTC.
> 3) Test against IGT, at least fbdev test and kms_flip test of it passed,
> while most tests of it passed.
> 4) Rewrite pixel PLL update function, magic numbers eliminated (Emil)
> 5) Drop a few common hardware features description in lsdc_desc (Emil)
> 6) Drop lsdc_mode_config_mode_valid(), instead add restrictions in dumb
> create function. (Emil)
> 7) Untangle the ls7a1000 case and ls7a2000 case completely (Thomas)
>
> v11 -> v12:
> none
>
> Signed-off-by: Li Yi <liyi@...ngson.cn>
> Signed-off-by: Sui Jingfeng <suijingfeng@...ngson.cn>
> ---
> drivers/gpu/drm/Kconfig | 2 +
> drivers/gpu/drm/Makefile | 1 +
> drivers/gpu/drm/loongson/Kconfig | 17 +
> drivers/gpu/drm/loongson/Makefile | 19 +
> drivers/gpu/drm/loongson/ls7a1000_outputs.c | 160 +++
> drivers/gpu/drm/loongson/ls7a2000_outputs.c | 534 ++++++++++
> drivers/gpu/drm/loongson/lsdc_crtc.c | 1064 +++++++++++++++++++
> drivers/gpu/drm/loongson/lsdc_debugfs.c | 78 ++
> drivers/gpu/drm/loongson/lsdc_device.c | 104 ++
> drivers/gpu/drm/loongson/lsdc_drv.c | 484 +++++++++
> drivers/gpu/drm/loongson/lsdc_drv.h | 485 +++++++++
> drivers/gpu/drm/loongson/lsdc_gem.c | 319 ++++++
> drivers/gpu/drm/loongson/lsdc_gem.h | 37 +
> drivers/gpu/drm/loongson/lsdc_gfxpll.c | 199 ++++
> drivers/gpu/drm/loongson/lsdc_gfxpll.h | 52 +
> drivers/gpu/drm/loongson/lsdc_i2c.c | 179 ++++
> drivers/gpu/drm/loongson/lsdc_i2c.h | 29 +
> drivers/gpu/drm/loongson/lsdc_irq.c | 81 ++
> drivers/gpu/drm/loongson/lsdc_irq.h | 16 +
> drivers/gpu/drm/loongson/lsdc_output.h | 21 +
> drivers/gpu/drm/loongson/lsdc_pixpll.c | 485 +++++++++
> drivers/gpu/drm/loongson/lsdc_pixpll.h | 86 ++
> drivers/gpu/drm/loongson/lsdc_plane.c | 639 +++++++++++
> drivers/gpu/drm/loongson/lsdc_probe.c | 56 +
> drivers/gpu/drm/loongson/lsdc_probe.h | 12 +
> drivers/gpu/drm/loongson/lsdc_regs.h | 400 +++++++
> drivers/gpu/drm/loongson/lsdc_ttm.c | 547 ++++++++++
> drivers/gpu/drm/loongson/lsdc_ttm.h | 88 ++
> 28 files changed, 6194 insertions(+)
> create mode 100644 drivers/gpu/drm/loongson/Kconfig
> create mode 100644 drivers/gpu/drm/loongson/Makefile
> create mode 100644 drivers/gpu/drm/loongson/ls7a1000_outputs.c
> create mode 100644 drivers/gpu/drm/loongson/ls7a2000_outputs.c
> create mode 100644 drivers/gpu/drm/loongson/lsdc_crtc.c
> create mode 100644 drivers/gpu/drm/loongson/lsdc_debugfs.c
> create mode 100644 drivers/gpu/drm/loongson/lsdc_device.c
> create mode 100644 drivers/gpu/drm/loongson/lsdc_drv.c
> create mode 100644 drivers/gpu/drm/loongson/lsdc_drv.h
> create mode 100644 drivers/gpu/drm/loongson/lsdc_gem.c
> create mode 100644 drivers/gpu/drm/loongson/lsdc_gem.h
> create mode 100644 drivers/gpu/drm/loongson/lsdc_gfxpll.c
> create mode 100644 drivers/gpu/drm/loongson/lsdc_gfxpll.h
> create mode 100644 drivers/gpu/drm/loongson/lsdc_i2c.c
> create mode 100644 drivers/gpu/drm/loongson/lsdc_i2c.h
> create mode 100644 drivers/gpu/drm/loongson/lsdc_irq.c
> create mode 100644 drivers/gpu/drm/loongson/lsdc_irq.h
> create mode 100644 drivers/gpu/drm/loongson/lsdc_output.h
> create mode 100644 drivers/gpu/drm/loongson/lsdc_pixpll.c
> create mode 100644 drivers/gpu/drm/loongson/lsdc_pixpll.h
> create mode 100644 drivers/gpu/drm/loongson/lsdc_plane.c
> create mode 100644 drivers/gpu/drm/loongson/lsdc_probe.c
> create mode 100644 drivers/gpu/drm/loongson/lsdc_probe.h
> create mode 100644 drivers/gpu/drm/loongson/lsdc_regs.h
> create mode 100644 drivers/gpu/drm/loongson/lsdc_ttm.c
> create mode 100644 drivers/gpu/drm/loongson/lsdc_ttm.h
>
> diff --git a/drivers/gpu/drm/Kconfig b/drivers/gpu/drm/Kconfig
> index ba3fb04bb691..d1fa87d2acb7 100644
> --- a/drivers/gpu/drm/Kconfig
> +++ b/drivers/gpu/drm/Kconfig
> @@ -331,6 +331,8 @@ source "drivers/gpu/drm/v3d/Kconfig"
>
> source "drivers/gpu/drm/vc4/Kconfig"
>
> +source "drivers/gpu/drm/loongson/Kconfig"
> +
> source "drivers/gpu/drm/etnaviv/Kconfig"
>
> source "drivers/gpu/drm/hisilicon/Kconfig"
> diff --git a/drivers/gpu/drm/Makefile b/drivers/gpu/drm/Makefile
> index a33257d2bc7f..131531453b8e 100644
> --- a/drivers/gpu/drm/Makefile
> +++ b/drivers/gpu/drm/Makefile
> @@ -194,3 +194,4 @@ obj-y += gud/
> obj-$(CONFIG_DRM_HYPERV) += hyperv/
> obj-y += solomon/
> obj-$(CONFIG_DRM_SPRD) += sprd/
> +obj-$(CONFIG_DRM_LOONGSON) += loongson/
> diff --git a/drivers/gpu/drm/loongson/Kconfig b/drivers/gpu/drm/loongson/Kconfig
> new file mode 100644
> index 000000000000..df6946d505fa
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/Kconfig
> @@ -0,0 +1,17 @@
> +# SPDX-License-Identifier: GPL-2.0
> +
> +config DRM_LOONGSON
> + tristate "DRM support for Loongson Graphics"
> + depends on DRM && PCI && MMU
> + select DRM_KMS_HELPER
> + select DRM_TTM
> + select I2C
> + select I2C_ALGOBIT
> + help
> + This is a DRM driver for Loongson Graphics, it may including
> + LS7A2000, LS7A1000, LS2K2000 and LS2K1000 etc. Loongson LS7A
> + series are bridge chipset, while Loongson LS2K series are SoC.
> +
> + If "M" is selected, the module will be called loongson.
> +
> + If in doubt, say "N".
> diff --git a/drivers/gpu/drm/loongson/Makefile b/drivers/gpu/drm/loongson/Makefile
> new file mode 100644
> index 000000000000..b9f5f7c2ecfd
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/Makefile
> @@ -0,0 +1,19 @@
> +# SPDX-License-Identifier: GPL-2.0
> +
> +loongson-y := \
> + lsdc_crtc.o \
> + lsdc_debugfs.o \
> + lsdc_device.o \
> + lsdc_drv.o \
> + lsdc_gem.o \
> + lsdc_gfxpll.o \
> + lsdc_i2c.o \
> + lsdc_irq.o \
> + lsdc_plane.o \
> + lsdc_pixpll.o \
> + lsdc_probe.o \
> + lsdc_ttm.o
> +
> +loongson-y += ls7a1000_outputs.o ls7a2000_outputs.o
> +
> +obj-$(CONFIG_DRM_LOONGSON) += loongson.o
> diff --git a/drivers/gpu/drm/loongson/ls7a1000_outputs.c b/drivers/gpu/drm/loongson/ls7a1000_outputs.c
> new file mode 100644
> index 000000000000..8bd3259700f6
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/ls7a1000_outputs.c
> @@ -0,0 +1,160 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2023 Loongson Corporation
Our regular name is "Loongson Technology Corporation Limited".
> + */
> +
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_edid.h>
> +#include <drm/drm_probe_helper.h>
> +
> +#include "lsdc_drv.h"
> +#include "lsdc_output.h"
> +
> +/*
> + * Currently, we assume the external encoders connected with the DVO is
> + * transparent. Loongson DVO interface can directly drive RGB888 panels.
> + *
> + * TODO: Add support for non-transparent encoders ...
> + */
> +
> +static int ls7a1000_generic_connector_get_modes(struct drm_connector *conn)
> +{
> + unsigned int num = 0;
> + struct edid *edid;
> +
> + if (conn->ddc) {
> + edid = drm_get_edid(conn, conn->ddc);
> + if (edid) {
> + drm_connector_update_edid_property(conn, edid);
> + num = drm_add_edid_modes(conn, edid);
> + kfree(edid);
> + }
> +
> + return num;
> + }
> +
> + num = drm_add_modes_noedid(conn, 1920, 1200);
> +
> + drm_set_preferred_mode(conn, 1024, 768);
> +
> + return num;
> +}
> +
> +static struct drm_encoder *
> +ls7a1000_generic_connector_get_best_encoder(struct drm_connector *connector,
> + struct drm_atomic_state *state)
> +{
> + struct lsdc_display_pipe *pipe = connector_to_display_pipe(connector);
> +
> + return &pipe->encoder;
> +}
> +
> +static const struct drm_connector_helper_funcs
> +ls7a1000_generic_connector_helpers = {
> + .atomic_best_encoder = ls7a1000_generic_connector_get_best_encoder,
> + .get_modes = ls7a1000_generic_connector_get_modes,
> +};
> +
> +static enum drm_connector_status
> +ls7a1000_generic_connector_detect(struct drm_connector *connector, bool force)
> +{
> + struct i2c_adapter *ddc = connector->ddc;
> +
> + if (ddc) {
> + if (drm_probe_ddc(ddc))
> + return connector_status_connected;
> +
> + return connector_status_disconnected;
> + }
> +
> + return connector_status_unknown;
> +}
> +
> +static const struct drm_connector_funcs ls7a1000_generic_connector_funcs = {
> + .detect = ls7a1000_generic_connector_detect,
> + .fill_modes = drm_helper_probe_single_connector_modes,
> + .destroy = drm_connector_cleanup,
> + .reset = drm_atomic_helper_connector_reset,
> + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state
> +};
> +
> +static void ls7a1000_pipe0_encoder_reset(struct drm_encoder *encoder)
> +{
> + struct drm_device *ddev = encoder->dev;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> +
> + /*
> + * We need this, for S3 resume, screen will not lightup if don't set
> + * correctly.
> + */
> + lsdc_wreg32(ldev, LSDC_CRTC0_PANEL_CONF_REG,
> + PHY_CLOCK_POL | PHY_CLOCK_EN | PHY_DATA_EN);
> +}
> +
> +static void ls7a1000_pipe1_encoder_reset(struct drm_encoder *encoder)
> +{
> + struct drm_device *ddev = encoder->dev;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> +
> + /*
> + * We need this, for S3 resume, screen will not lightup if don't set
> + * correctly.
> + */
> + lsdc_wreg32(ldev, LSDC_CRTC1_PANEL_CONF_REG,
> + PHY_CLOCK_POL | PHY_CLOCK_EN | PHY_DATA_EN);
> +}
> +
> +static const struct drm_encoder_funcs ls7a1000_encoder_funcs[2] = {
> + {
> + .reset = ls7a1000_pipe0_encoder_reset,
> + .destroy = drm_encoder_cleanup,
> + },
> + {
> + .reset = ls7a1000_pipe1_encoder_reset,
> + .destroy = drm_encoder_cleanup,
> + },
> +};
> +
> +int ls7a1000_output_init(struct drm_device *ddev,
> + struct lsdc_display_pipe *dispipe,
> + struct i2c_adapter *ddc,
> + unsigned int pipe)
> +{
> + struct drm_encoder *encoder = &dispipe->encoder;
> + struct drm_connector *connector = &dispipe->connector;
> + int ret;
> +
> + ret = drm_encoder_init(ddev,
> + encoder,
> + &ls7a1000_encoder_funcs[pipe],
> + DRM_MODE_ENCODER_TMDS,
> + "encoder-%u",
> + dispipe->index);
> + if (ret)
> + return ret;
> +
> + encoder->possible_crtcs = BIT(pipe);
> +
> + ret = drm_connector_init_with_ddc(ddev,
> + connector,
> + &ls7a1000_generic_connector_funcs,
> + DRM_MODE_CONNECTOR_DPI,
> + ddc);
> + if (ret)
> + return ret;
> +
> + drm_info(ddev, "display pipe-%u has a DVO\n", pipe);
> +
> + drm_connector_helper_add(connector, &ls7a1000_generic_connector_helpers);
> +
> + drm_connector_attach_encoder(connector, encoder);
> +
> + connector->polled = DRM_CONNECTOR_POLL_CONNECT |
> + DRM_CONNECTOR_POLL_DISCONNECT;
> +
> + connector->interlace_allowed = 0;
> + connector->doublescan_allowed = 0;
> +
> + return 0;
> +}
> diff --git a/drivers/gpu/drm/loongson/ls7a2000_outputs.c b/drivers/gpu/drm/loongson/ls7a2000_outputs.c
> new file mode 100644
> index 000000000000..5ee37da3b88e
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/ls7a2000_outputs.c
> @@ -0,0 +1,534 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#include <linux/delay.h>
> +
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_debugfs.h>
> +#include <drm/drm_edid.h>
> +#include <drm/drm_file.h>
> +#include <drm/drm_probe_helper.h>
> +
> +#include "lsdc_drv.h"
> +#include "lsdc_output.h"
> +
> +static int ls7a2000_connector_get_modes(struct drm_connector *connector)
> +{
> + unsigned int num = 0;
> + struct edid *edid;
> +
> + if (connector->ddc) {
> + edid = drm_get_edid(connector, connector->ddc);
> + if (edid) {
> + drm_connector_update_edid_property(connector, edid);
> + num = drm_add_edid_modes(connector, edid);
> + kfree(edid);
> + }
> +
> + return num;
> + }
> +
> + num = drm_add_modes_noedid(connector, 1920, 1200);
> +
> + drm_set_preferred_mode(connector, 1024, 768);
> +
> + return num;
> +}
> +
> +static struct drm_encoder *
> +ls7a2000_connector_get_best_encoder(struct drm_connector *connector,
> + struct drm_atomic_state *state)
> +{
> + struct lsdc_display_pipe *dispipe;
> +
> + dispipe = connector_to_display_pipe(connector);
> +
> + return &dispipe->encoder;
> +}
> +
> +static const struct drm_connector_helper_funcs ls7a2000_connector_helpers = {
> + .atomic_best_encoder = ls7a2000_connector_get_best_encoder,
> + .get_modes = ls7a2000_connector_get_modes,
> +};
> +
> +/* debugfs */
> +
> +#define LSDC_HDMI_REG(i, reg) { \
> + .name = __stringify_1(LSDC_HDMI##i##_##reg##_REG), \
> + .offset = LSDC_HDMI##i##_##reg##_REG, \
> +}
> +
> +static const struct lsdc_reg32 ls7a2000_hdmi0_encoder_regs[] = {
> + LSDC_HDMI_REG(0, ZONE),
> + LSDC_HDMI_REG(0, INTF_CTRL),
> + LSDC_HDMI_REG(0, PHY_CTRL),
> + LSDC_HDMI_REG(0, PHY_PLL),
> + LSDC_HDMI_REG(0, AVI_INFO_CRTL),
> + LSDC_HDMI_REG(0, PHY_CAL),
> + LSDC_HDMI_REG(0, AUDIO_PLL_LO),
> + LSDC_HDMI_REG(0, AUDIO_PLL_HI),
> + {NULL, 0}, /* MUST be {NULL, 0} terminated */
> +};
> +
> +static const struct lsdc_reg32 ls7a2000_hdmi1_encoder_regs[] = {
> + LSDC_HDMI_REG(1, ZONE),
> + LSDC_HDMI_REG(1, INTF_CTRL),
> + LSDC_HDMI_REG(1, PHY_CTRL),
> + LSDC_HDMI_REG(1, PHY_PLL),
> + LSDC_HDMI_REG(1, AVI_INFO_CRTL),
> + LSDC_HDMI_REG(1, PHY_CAL),
> + LSDC_HDMI_REG(1, AUDIO_PLL_LO),
> + LSDC_HDMI_REG(1, AUDIO_PLL_HI),
> + {NULL, 0}, /* MUST be {NULL, 0} terminated */
> +};
> +
> +static int ls7a2000_hdmi_encoder_regs_show(struct seq_file *m, void *data)
> +{
> + struct drm_info_node *node = (struct drm_info_node *)m->private;
> + struct drm_device *ddev = node->minor->dev;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + const struct lsdc_reg32 *preg;
> +
> + preg = (const struct lsdc_reg32 *)node->info_ent->data;
> +
> + while (preg->name) {
> + u32 offset = preg->offset;
> +
> + seq_printf(m, "%s (0x%04x): 0x%08x\n",
> + preg->name, offset, lsdc_rreg32(ldev, offset));
> + ++preg;
> + }
> +
> + return 0;
> +}
> +
> +static const struct drm_info_list ls7a2000_hdmi0_debugfs_files[] = {
> + { "regs", ls7a2000_hdmi_encoder_regs_show, 0, (void *)ls7a2000_hdmi0_encoder_regs },
> +};
> +
> +static const struct drm_info_list ls7a2000_hdmi1_debugfs_files[] = {
> + { "regs", ls7a2000_hdmi_encoder_regs_show, 0, (void *)ls7a2000_hdmi1_encoder_regs },
> +};
> +
> +static void ls7a2000_hdmi0_late_register(struct drm_connector *connector,
> + struct dentry *root)
> +{
> + struct drm_device *ddev = connector->dev;
> + struct drm_minor *minor = ddev->primary;
> +
> + drm_debugfs_create_files(ls7a2000_hdmi0_debugfs_files,
> + ARRAY_SIZE(ls7a2000_hdmi0_debugfs_files),
> + root,
> + minor);
Don't need split to so many lines, the last three lines can be combined.
> +}
> +
> +static void ls7a2000_hdmi1_late_register(struct drm_connector *connector,
> + struct dentry *root)
> +{
> + struct drm_device *ddev = connector->dev;
> + struct drm_minor *minor = ddev->primary;
> +
> + drm_debugfs_create_files(ls7a2000_hdmi1_debugfs_files,
> + ARRAY_SIZE(ls7a2000_hdmi1_debugfs_files),
> + root,
> + minor);
> +}
> +
> +/* monitor present detection */
> +
> +static enum drm_connector_status
> +ls7a2000_hdmi0_vga_connector_detect(struct drm_connector *connector, bool force)
> +{
> + struct drm_device *ddev = connector->dev;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + u32 val;
> +
> + val = lsdc_rreg32(ldev, LSDC_HDMI_HPD_STATUS_REG);
> +
> + if (val & HDMI0_HPD_FLAG)
> + return connector_status_connected;
> +
> + if (connector->ddc) {
> + if (drm_probe_ddc(connector->ddc))
> + return connector_status_connected;
> +
> + return connector_status_disconnected;
> + }
> +
> + return connector_status_unknown;
> +}
> +
> +static enum drm_connector_status
> +ls7a2000_hdmi1_connector_detect(struct drm_connector *connector, bool force)
> +{
> + struct lsdc_device *ldev = to_lsdc(connector->dev);
> + u32 val;
> +
> + val = lsdc_rreg32(ldev, LSDC_HDMI_HPD_STATUS_REG);
> +
> + if (val & HDMI1_HPD_FLAG)
> + return connector_status_connected;
> +
> + return connector_status_disconnected;
> +}
> +
> +static const struct drm_connector_funcs ls7a2000_hdmi_connector_funcs[2] = {
> + {
> + .detect = ls7a2000_hdmi0_vga_connector_detect,
> + .fill_modes = drm_helper_probe_single_connector_modes,
> + .destroy = drm_connector_cleanup,
> + .reset = drm_atomic_helper_connector_reset,
> + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> + .debugfs_init = ls7a2000_hdmi0_late_register,
> + },
> + {
> + .detect = ls7a2000_hdmi1_connector_detect,
> + .fill_modes = drm_helper_probe_single_connector_modes,
> + .destroy = drm_connector_cleanup,
> + .reset = drm_atomic_helper_connector_reset,
> + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> + .debugfs_init = ls7a2000_hdmi1_late_register,
> + },
> +};
> +
> +/* Even though some board has only one hdmi on display pipe 1,
> + * We still need hook lsdc_encoder_funcs up on display pipe 0,
> + * This is because we need its reset() callback get called, to
> + * set the LSDC_HDMIx_CTRL_REG using software gpio emulated i2c.
> + * Otherwise, the firmware may set LSDC_HDMIx_CTRL_REG blindly.
> + */
> +static void ls7a2000_hdmi0_encoder_reset(struct drm_encoder *encoder)
> +{
> + struct drm_device *ddev = encoder->dev;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + u32 val;
> +
> + val = PHY_CLOCK_POL | PHY_CLOCK_EN | PHY_DATA_EN;
> + lsdc_wreg32(ldev, LSDC_CRTC0_PANEL_CONF_REG, val);
> +
> + /* using software gpio emulated i2c */
> + val = lsdc_rreg32(ldev, LSDC_HDMI0_INTF_CTRL_REG);
> + val &= ~HW_I2C_EN;
> + val |= HDMI_INTERFACE_EN | HDMI_PACKET_EN;
> + lsdc_wreg32(ldev, LSDC_HDMI0_INTF_CTRL_REG, val);
> +
> + /* get out of reset state */
> + val |= HDMI_PHY_RESET_N;
> + lsdc_wreg32(ldev, LSDC_HDMI0_PHY_CTRL_REG, val);
> +
> + mdelay(20);
> +
> + drm_dbg(ddev, "HDMI-0 Reset\n");
> +}
> +
> +static void ls7a2000_hdmi1_encoder_reset(struct drm_encoder *encoder)
> +{
> + struct drm_device *ddev = encoder->dev;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + u32 val;
> +
> + val = PHY_CLOCK_POL | PHY_CLOCK_EN | PHY_DATA_EN;
> + lsdc_wreg32(ldev, LSDC_CRTC1_PANEL_CONF_REG, val);
> +
> + /* using software gpio emulated i2c */
> + val = lsdc_rreg32(ldev, LSDC_HDMI1_INTF_CTRL_REG);
> + val &= ~HW_I2C_EN;
> + val |= HDMI_INTERFACE_EN | HDMI_PACKET_EN;
> + lsdc_wreg32(ldev, LSDC_HDMI1_INTF_CTRL_REG, val);
> +
> + /* reset */
> +
> + /* get out of reset state */
> + val = HDMI_PHY_RESET_N;
> + lsdc_wreg32(ldev, LSDC_HDMI1_PHY_CTRL_REG, val);
> +
> + mdelay(20);
> +
> + drm_dbg(ddev, "HDMI-1 Reset\n");
> +}
> +
> +static const struct drm_encoder_funcs ls7a2000_encoder_funcs[2] = {
> + {
> + .reset = ls7a2000_hdmi0_encoder_reset,
> + .destroy = drm_encoder_cleanup,
> + },
> + {
> + .reset = ls7a2000_hdmi1_encoder_reset,
> + .destroy = drm_encoder_cleanup,
> + }
> +};
> +
> +static int ls7a2000_hdmi_set_avi_infoframe(struct drm_encoder *encoder,
> + struct drm_display_mode *mode)
> +{
> + struct lsdc_display_pipe *dispipe = encoder_to_display_pipe(encoder);
> + struct drm_device *ddev = encoder->dev;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + unsigned int index = dispipe->index;
> + struct hdmi_avi_infoframe infoframe;
> + u8 buffer[HDMI_INFOFRAME_SIZE(AVI)];
> + unsigned char *ptr = &buffer[HDMI_INFOFRAME_HEADER_SIZE];
> + unsigned int content0, content1, content2, content3;
> + int err;
> +
> + err = drm_hdmi_avi_infoframe_from_display_mode(&infoframe,
> + &dispipe->connector,
> + mode);
As above, the last two lines can be combined.
> + if (err < 0) {
> + drm_err(ddev, "failed to setup AVI infoframe: %d\n", err);
> + return err;
> + }
> +
> + /* Fixed infoframe configuration not linked to the mode */
> + infoframe.colorspace = HDMI_COLORSPACE_RGB;
> + infoframe.quantization_range = HDMI_QUANTIZATION_RANGE_DEFAULT;
> + infoframe.colorimetry = HDMI_COLORIMETRY_NONE;
> +
> + err = hdmi_avi_infoframe_pack(&infoframe, buffer, sizeof(buffer));
> + if (err < 0) {
> + drm_err(ddev, "failed to pack AVI infoframe: %d\n", err);
> + return err;
> + }
> +
> + content0 = *(unsigned int *)ptr;
> + content1 = *(ptr + 4);
> + content2 = *(unsigned int *)(ptr + 5);
> + content3 = *(unsigned int *)(ptr + 9);
> +
> + lsdc_hdmi_wreg32(ldev, LSDC_HDMI0_AVI_CONTENT0, index, content0);
> + lsdc_hdmi_wreg32(ldev, LSDC_HDMI0_AVI_CONTENT1, index, content1);
> + lsdc_hdmi_wreg32(ldev, LSDC_HDMI0_AVI_CONTENT2, index, content2);
> + lsdc_hdmi_wreg32(ldev, LSDC_HDMI0_AVI_CONTENT3, index, content3);
> +
> + lsdc_hdmi_wreg32(ldev, LSDC_HDMI0_AVI_INFO_CRTL_REG, index,
> + AVI_PKT_ENABLE | AVI_PKT_UPDATE);
> +
> + drm_dbg(ddev, "Update HDMI-%u avi infoframe\n", index);
> +
> + return 0;
> +}
> +
> +static void ls7a2000_hdmi_atomic_disable(struct drm_encoder *encoder,
> + struct drm_atomic_state *state)
> +{
> + struct lsdc_display_pipe *dispipe = encoder_to_display_pipe(encoder);
> + struct drm_device *ddev = encoder->dev;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + unsigned int index = dispipe->index;
> + u32 val;
> +
> + /* Disable the hdmi phy */
> + val = lsdc_hdmi_rreg32(ldev, LSDC_HDMI0_PHY_CTRL_REG, index);
> + val &= ~HDMI_PHY_EN;
> + lsdc_hdmi_wreg32(ldev, LSDC_HDMI0_PHY_CTRL_REG, index, val);
> +
> + /* Disable the hdmi interface */
> + val = lsdc_hdmi_rreg32(ldev, LSDC_HDMI0_INTF_CTRL_REG, index);
> + val &= ~HDMI_INTERFACE_EN;
> + lsdc_hdmi_wreg32(ldev, LSDC_HDMI0_INTF_CTRL_REG, index, val);
> +
> + drm_dbg(ddev, "HDMI-%u disabled\n", index);
> +}
> +
> +static void ls7a2000_hdmi_atomic_enable(struct drm_encoder *encoder,
> + struct drm_atomic_state *state)
> +{
> + struct drm_device *ddev = encoder->dev;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + struct lsdc_display_pipe *dispipe = encoder_to_display_pipe(encoder);
> + unsigned int index = dispipe->index;
> + u32 val;
> +
> + /* datasheet say it should larger than 48 */
> + val = 64 << HDMI_H_ZONE_IDLE_SHIFT | 64 << HDMI_V_ZONE_IDLE_SHIFT;
> +
> + lsdc_hdmi_wreg32(ldev, LSDC_HDMI0_ZONE_REG, index, val);
> +
> + val = HDMI_PHY_TERM_STATUS |
> + HDMI_PHY_TERM_DET_EN |
> + HDMI_PHY_TERM_H_EN |
> + HDMI_PHY_TERM_L_EN |
> + HDMI_PHY_RESET_N |
> + HDMI_PHY_EN;
> +
> + lsdc_hdmi_wreg32(ldev, LSDC_HDMI0_PHY_CTRL_REG, index, val);
> +
> + udelay(2);
> +
> + val = HDMI_CTL_PERIOD_MODE |
> + HDMI_AUDIO_EN |
> + HDMI_PACKET_EN |
> + HDMI_INTERFACE_EN |
> + (8 << HDMI_VIDEO_PREAMBLE_SHIFT);
> +
> + lsdc_hdmi_wreg32(ldev, LSDC_HDMI0_INTF_CTRL_REG, index, val);
> +
> + drm_dbg(ddev, "HDMI-%u enabled\n", index);
> +}
> +
> +/*
> + * Fout = M * Fin
> + *
> + * M = (4 * LF) / (IDF * ODF)
> + *
> + * IDF: Input Division Factor
> + * ODF: Output Division Factor
> + * LF: Loop Factor
> + * M: Required Mult
> + *
> + * +--------------------------------------------------------+
> + * | Fin (kHZ) | M | IDF | LF | ODF | Fout(Mhz) |
> + * |-------------------+----+-----+----+-----+--------------|
> + * | 170000 ~ 340000 | 10 | 16 | 40 | 1 | 1700 ~ 3400 |
> + * | 85000 ~ 170000 | 10 | 8 | 40 | 2 | 850 ~ 1700 |
> + * | 42500 ~ 85000 | 10 | 4 | 40 | 4 | 425 ~ 850 |
> + * | 21250 ~ 42500 | 10 | 2 | 40 | 8 | 212.5 ~ 425 |
> + * | 20000 ~ 21250 | 10 | 1 | 40 | 16 | 200 ~ 212.5 |
> + * +--------------------------------------------------------+
> + */
> +static void ls7a2000_hdmi_phy_pll_config(struct lsdc_device *ldev,
> + int fin,
> + unsigned int index)
> +{
> + struct drm_device *ddev = &ldev->base;
> + int count = 0;
> + u32 val;
> +
> + /* Firstly, disable phy pll */
> + lsdc_hdmi_wreg32(ldev, LSDC_HDMI0_PHY_PLL_REG, index, 0x0);
> +
> + /*
> + * Most of time, loongson HDMI require M = 10
> + * for example, 10 = (4 * 40) / (8 * 2)
> + * here, write "1" to the ODF will get "2"
> + */
> +
> + if (fin >= 170000)
> + val = (16 << HDMI_PLL_IDF_SHIFT) |
> + (40 << HDMI_PLL_LF_SHIFT) |
> + (0 << HDMI_PLL_ODF_SHIFT);
> + else if (fin >= 85000)
> + val = (8 << HDMI_PLL_IDF_SHIFT) |
> + (40 << HDMI_PLL_LF_SHIFT) |
> + (1 << HDMI_PLL_ODF_SHIFT);
> + else if (fin >= 42500)
> + val = (4 << HDMI_PLL_IDF_SHIFT) |
> + (40 << HDMI_PLL_LF_SHIFT) |
> + (2 << HDMI_PLL_ODF_SHIFT);
> + else if (fin >= 21250)
> + val = (2 << HDMI_PLL_IDF_SHIFT) |
> + (40 << HDMI_PLL_LF_SHIFT) |
> + (3 << HDMI_PLL_ODF_SHIFT);
> + else
> + val = (1 << HDMI_PLL_IDF_SHIFT) |
> + (40 << HDMI_PLL_LF_SHIFT) |
> + (4 << HDMI_PLL_ODF_SHIFT);
> +
> + lsdc_hdmi_wreg32(ldev, LSDC_HDMI0_PHY_PLL_REG, index, val);
> +
> + val |= HDMI_PLL_ENABLE;
> +
> + lsdc_hdmi_wreg32(ldev, LSDC_HDMI0_PHY_PLL_REG, index, val);
> +
> + udelay(2);
> +
> + drm_dbg(ddev, "Fin of HDMI-%u: %d kHz\n", index, fin);
> +
> + /* Wait hdmi phy pll lock */
> + do {
> + val = lsdc_hdmi_rreg32(ldev, LSDC_HDMI0_PHY_PLL_REG, index);
> +
> + if (val & HDMI_PLL_LOCKED) {
> + drm_dbg(ddev, "Setting HDMI-%u PLL take %d cycles\n",
> + index, count);
> + break;
> + }
> + ++count;
> + } while (count < 1000);
> +
> + lsdc_hdmi_wreg32(ldev, LSDC_HDMI0_PHY_CAL_REG, index, 0x0f000ff0);
> +
> + if (count >= 1000)
> + drm_err(ddev, "Setting HDMI-%u PLL failed\n", index);
> +}
> +
> +static void ls7a2000_hdmi_atomic_mode_set(struct drm_encoder *encoder,
> + struct drm_crtc_state *crtc_state,
> + struct drm_connector_state *conn_state)
> +{
> + struct lsdc_display_pipe *dispipe = encoder_to_display_pipe(encoder);
> + struct drm_device *ddev = encoder->dev;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + struct drm_display_mode *mode = &crtc_state->mode;
> +
> + ls7a2000_hdmi_phy_pll_config(ldev, mode->clock, dispipe->index);
> +
> + ls7a2000_hdmi_set_avi_infoframe(encoder, mode);
> +
> + drm_dbg(ddev, "HDMI-%u modeset finished\n", dispipe->index);
> +}
> +
> +static const struct drm_encoder_helper_funcs ls7a2000_encoder_helper_funcs = {
> + .atomic_disable = ls7a2000_hdmi_atomic_disable,
> + .atomic_enable = ls7a2000_hdmi_atomic_enable,
> + .atomic_mode_set = ls7a2000_hdmi_atomic_mode_set,
> +};
> +
> +/*
> + * For LS7A2000:
> + *
> + * 1) Most of board export one vga + hdmi output interface.
> + * 2) Yet, Some boards export double hdmi output interface.
> + * 3) Still have boards export three output(2 hdmi + 1 vga).
> + *
> + * So let's hook hdmi helper funcs to all display pipe, don't miss.
> + * writing hdmi register do no harms.
> + */
> +int ls7a2000_output_init(struct drm_device *ddev,
> + struct lsdc_display_pipe *dispipe,
> + struct i2c_adapter *ddc,
> + unsigned int pipe)
> +{
> + struct drm_encoder *encoder = &dispipe->encoder;
> + struct drm_connector *connector = &dispipe->connector;
> + int ret;
> +
> + ret = drm_encoder_init(ddev,
> + encoder,
> + &ls7a2000_encoder_funcs[pipe],
> + DRM_MODE_ENCODER_TMDS,
> + "encoder-%u",
> + pipe);
Same problem.
> + if (ret)
> + return ret;
> +
> + encoder->possible_crtcs = BIT(pipe);
> +
> + drm_encoder_helper_add(encoder, &ls7a2000_encoder_helper_funcs);
> +
> + ret = drm_connector_init_with_ddc(ddev,
> + connector,
> + &ls7a2000_hdmi_connector_funcs[pipe],
> + DRM_MODE_CONNECTOR_HDMIA,
> + ddc);
Same problem.
> + if (ret)
> + return ret;
> +
> + drm_info(ddev, "display pipe-%u has HDMI %s\n", pipe, pipe ? "" : "and/or VGA");
> +
> + drm_connector_helper_add(connector, &ls7a2000_connector_helpers);
> +
> + drm_connector_attach_encoder(connector, encoder);
> +
> + connector->polled = DRM_CONNECTOR_POLL_CONNECT |
> + DRM_CONNECTOR_POLL_DISCONNECT;
> +
> + connector->interlace_allowed = 0;
> + connector->doublescan_allowed = 0;
> +
> + return 0;
> +}
> diff --git a/drivers/gpu/drm/loongson/lsdc_crtc.c b/drivers/gpu/drm/loongson/lsdc_crtc.c
> new file mode 100644
> index 000000000000..9c23fa569dd5
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_crtc.c
> @@ -0,0 +1,1064 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#include <linux/delay.h>
> +
> +#include <drm/drm_atomic.h>
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_debugfs.h>
> +#include <drm/drm_vblank.h>
> +
> +#include "lsdc_drv.h"
> +
> +/*
> + * The soft reset cause the vblank counter reset to zero, but the address
> + * and other settings in the crtc register remains.
> + */
> +
> +static void lsdc_crtc0_soft_reset(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> + u32 val;
> +
> + val = lsdc_rreg32(ldev, LSDC_CRTC0_CFG_REG);
> +
> + val &= CFG_VALID_BITS_MASK;
> +
> + /* soft reset bit, active low */
> + val &= ~CFG_RESET_N;
> +
> + val &= ~CFG_PIX_FMT_MASK;
> +
> + lsdc_wreg32(ldev, LSDC_CRTC0_CFG_REG, val);
> +
> + udelay(5);
> +
> + val |= CFG_RESET_N | LSDC_PF_XRGB8888 | CFG_OUTPUT_ENABLE;
> +
> + lsdc_wreg32(ldev, LSDC_CRTC0_CFG_REG, val);
> +
> + mdelay(20);
> +}
> +
> +static void lsdc_crtc1_soft_reset(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> + u32 val;
> +
> + val = lsdc_rreg32(ldev, LSDC_CRTC1_CFG_REG);
> +
> + val &= CFG_VALID_BITS_MASK;
> +
> + /* soft reset bit, active low */
> + val &= ~CFG_RESET_N;
> +
> + val &= ~CFG_PIX_FMT_MASK;
> +
> + lsdc_wreg32(ldev, LSDC_CRTC1_CFG_REG, val);
> +
> + udelay(5);
> +
> + val |= CFG_RESET_N | LSDC_PF_XRGB8888 | CFG_OUTPUT_ENABLE;
> +
> + lsdc_wreg32(ldev, LSDC_CRTC1_CFG_REG, val);
> +
> + msleep(20);
> +}
> +
> +static void lsdc_crtc0_enable(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> + u32 val;
> +
> + val = lsdc_rreg32(ldev, LSDC_CRTC0_CFG_REG);
> +
> + /*
> + * If bit 24 of LSDC_CRTC0_CFG_REG is set, it say that the DC hardware
> + * stop working anymore, anchored. This maybe caused by improper
> + * operation sequence, may happens on extreme rarely case.
> + *
> + * Luckily, a soft reset helps bring it to normal on such a case.
> + * So we add a warn here, hope to catch something if it happens.
> + */
> +
> + if (val & BIT(24)) {
> + drm_warn(&ldev->base, "%s anchored\n", lcrtc->base.name);
> + return lsdc_crtc0_soft_reset(lcrtc);
> + }
> +
> + lsdc_wreg32(ldev, LSDC_CRTC0_CFG_REG, val | CFG_OUTPUT_ENABLE);
> +}
> +
> +static void lsdc_crtc0_disable(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> +
> + lsdc_ureg32_clr(ldev, LSDC_CRTC0_CFG_REG, CFG_OUTPUT_ENABLE);
> +
> + udelay(9);
> +}
> +
> +static void lsdc_crtc1_enable(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> + u32 val;
> +
> + val = lsdc_rreg32(ldev, LSDC_CRTC1_CFG_REG);
> + if (val & BIT(24)) {
> + drm_warn(&ldev->base, "%s anchored\n", lcrtc->base.name);
> + return lsdc_crtc1_soft_reset(lcrtc);
> + }
> +
> + lsdc_wreg32(ldev, LSDC_CRTC1_CFG_REG, val | CFG_OUTPUT_ENABLE);
> +}
> +
> +static void lsdc_crtc1_disable(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> +
> + lsdc_ureg32_clr(ldev, LSDC_CRTC1_CFG_REG, CFG_OUTPUT_ENABLE);
> +
> + udelay(9);
> +}
> +
> +/* All loongson display controller support scanout position hardware */
> +
> +static void lsdc_crtc0_scan_pos(struct lsdc_crtc *lcrtc, int *hpos, int *vpos)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> + u32 val;
> +
> + val = lsdc_rreg32(ldev, LSDC_CRTC0_SCAN_POS_REG);
> +
> + *hpos = val >> 16;
> + *vpos = val & 0xffff;
> +}
> +
> +static void lsdc_crtc1_scan_pos(struct lsdc_crtc *lcrtc, int *hpos, int *vpos)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> + u32 val;
> +
> + val = lsdc_rreg32(ldev, LSDC_CRTC1_SCAN_POS_REG);
> +
> + *hpos = val >> 16;
> + *vpos = val & 0xffff;
> +}
> +
> +static void lsdc_crtc0_enable_vblank(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> +
> + lsdc_ureg32_set(ldev, LSDC_INT_REG, INT_CRTC0_VSYNC_EN);
> +}
> +
> +static void lsdc_crtc0_disable_vblank(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> +
> + lsdc_ureg32_clr(ldev, LSDC_INT_REG, INT_CRTC0_VSYNC_EN);
> +}
> +
> +static void lsdc_crtc1_enable_vblank(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> +
> + lsdc_ureg32_set(ldev, LSDC_INT_REG, INT_CRTC1_VSYNC_EN);
> +}
> +
> +static void lsdc_crtc1_disable_vblank(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> +
> + lsdc_ureg32_clr(ldev, LSDC_INT_REG, INT_CRTC1_VSYNC_EN);
> +}
> +
> +static void lsdc_crtc0_flip(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> +
> + lsdc_ureg32_set(ldev, LSDC_CRTC0_CFG_REG, CFG_PAGE_FLIP);
> +}
> +
> +static void lsdc_crtc1_flip(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> +
> + lsdc_ureg32_set(ldev, LSDC_CRTC1_CFG_REG, CFG_PAGE_FLIP);
> +}
> +
> +/*
> + * CRTC0 clone from CRTC1 or CRTC1 clone from CRTC0 using hardware logic.
> + * Hardware engineer say this would help to saving bandwidth on clone mode.
> + *
> + * This may useful on custom clone application.
> + */
> +
> +static void lsdc_crtc0_clone(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> +
> + lsdc_ureg32_set(ldev, LSDC_CRTC0_CFG_REG, CFG_HW_CLONE);
> +}
> +
> +static void lsdc_crtc1_clone(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> +
> + lsdc_ureg32_set(ldev, LSDC_CRTC1_CFG_REG, CFG_HW_CLONE);
> +}
> +
> +static void lsdc_crtc0_set_mode(struct lsdc_crtc *lcrtc,
> + const struct drm_display_mode *mode)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> +
> + lsdc_wreg32(ldev, LSDC_CRTC0_HDISPLAY_REG,
> + (mode->crtc_htotal << 16) | mode->crtc_hdisplay);
> +
> + lsdc_wreg32(ldev, LSDC_CRTC0_VDISPLAY_REG,
> + (mode->crtc_vtotal << 16) | mode->crtc_vdisplay);
> +
> + lsdc_wreg32(ldev, LSDC_CRTC0_HSYNC_REG,
> + (mode->crtc_hsync_end << 16) | mode->crtc_hsync_start | HSYNC_EN);
> +
> + lsdc_wreg32(ldev, LSDC_CRTC0_VSYNC_REG,
> + (mode->crtc_vsync_end << 16) | mode->crtc_vsync_start | VSYNC_EN);
> +}
> +
> +static void lsdc_crtc1_set_mode(struct lsdc_crtc *lcrtc,
> + const struct drm_display_mode *mode)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> +
> + lsdc_wreg32(ldev, LSDC_CRTC1_HDISPLAY_REG,
> + (mode->crtc_htotal << 16) | mode->crtc_hdisplay);
> +
> + lsdc_wreg32(ldev, LSDC_CRTC1_VDISPLAY_REG,
> + (mode->crtc_vtotal << 16) | mode->crtc_vdisplay);
> +
> + lsdc_wreg32(ldev, LSDC_CRTC1_HSYNC_REG,
> + (mode->crtc_hsync_end << 16) | mode->crtc_hsync_start | HSYNC_EN);
> +
> + lsdc_wreg32(ldev, LSDC_CRTC1_VSYNC_REG,
> + (mode->crtc_vsync_end << 16) | mode->crtc_vsync_start | VSYNC_EN);
> +}
> +
> +/*
> + * This is required for S3 support.
> + *
> + * After resume from suspend, LSDC_CRTCx_CFG_REG (x=0 or 1)is filled with
> + * garbarge value which may cause the CRTC completely hang. This function
> + * give a minimal setting to the affected registers. This also override
> + * the firmware's setting on startup, eliminate potential blinding setting.
> + *
> + * Making the CRTC works on our own now, this is similar with the functional
> + * of GPU POST(Power On Self Test). Only touch CRTC hardware related part.
> + */
> +
> +static void lsdc_crtc0_reset(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> + struct drm_crtc *crtc = &lcrtc->base;
> + u32 val;
> +
> + val = lsdc_rreg32(ldev, LSDC_CRTC0_CFG_REG);
> +
> + /* This help to see what is it */
> + drm_dbg(&ldev->base, "value of %s configure register: %x\n",
> + crtc->name, val);
> +
> + /*
> + * Help the CRTC get out of soft reset sate, as the CRTC is completely
> + * halt on soft reset mode (BIT(20) = 0). It does not event generate
> + * vblank, cause vblank wait timeout. This happends when resume from
> + * S3.
> + *
> + * Also give a sane format, after resume from suspend S3, this
> + * register is filled with garbarge value. A meaningless value may
> + * also cause the CRTC halt or crash.
> + */
> +
> + val = CFG_RESET_N | LSDC_PF_XRGB8888;
> +
> + lsdc_wreg32(ldev, LSDC_CRTC0_CFG_REG, val);
> +}
> +
> +static void lsdc_crtc1_reset(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> + struct drm_crtc *crtc = &lcrtc->base;
> + u32 val;
> +
> + val = lsdc_rreg32(ldev, LSDC_CRTC1_CFG_REG);
> +
> + drm_dbg(&ldev->base, "value of %s configue register: %x\n",
> + crtc->name, val);
> +
> + /*
> + * Help the CRTC get out of soft reset sate, give a sane format,
> + * Otherwise it will complete halt there.
> + */
> + val = CFG_RESET_N | LSDC_PF_XRGB8888;
> +
> + lsdc_wreg32(ldev, LSDC_CRTC1_CFG_REG, val);
> +}
> +
> +static const struct lsdc_crtc_hw_ops ls7a1000_crtc_hw_ops[2] = {
> + {
> + .enable = lsdc_crtc0_enable,
> + .disable = lsdc_crtc0_disable,
> + .enable_vblank = lsdc_crtc0_enable_vblank,
> + .disable_vblank = lsdc_crtc0_disable_vblank,
> + .flip = lsdc_crtc0_flip,
> + .clone = lsdc_crtc0_clone,
> + .set_mode = lsdc_crtc0_set_mode,
> + .get_scan_pos = lsdc_crtc0_scan_pos,
> + .soft_reset = lsdc_crtc0_soft_reset,
> + .reset = lsdc_crtc0_reset,
> + },
> + {
> + .enable = lsdc_crtc1_enable,
> + .disable = lsdc_crtc1_disable,
> + .enable_vblank = lsdc_crtc1_enable_vblank,
> + .disable_vblank = lsdc_crtc1_disable_vblank,
> + .flip = lsdc_crtc1_flip,
> + .clone = lsdc_crtc1_clone,
> + .set_mode = lsdc_crtc1_set_mode,
> + .get_scan_pos = lsdc_crtc1_scan_pos,
> + .soft_reset = lsdc_crtc1_soft_reset,
> + .reset = lsdc_crtc1_reset,
> + },
> +};
> +
> +/*
> + * The 32-bit hardware vblank counter is available since ls7a2000/ls2k2000,
> + * The counter grow up even the CRTC is being disabled, it will got reset
> + * if the crtc is being soft reset.
> + *
> + * Those registers are also readable for ls7a1000, but its value does not
> + * change.
> + */
> +
> +static u32 lsdc_crtc0_get_vblank_count(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> +
> + return lsdc_rreg32(ldev, LSDC_CRTC0_VSYNC_COUNTER_REG);
> +}
> +
> +static u32 lsdc_crtc1_get_vblank_count(struct lsdc_crtc *lcrtc)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> +
> + return lsdc_rreg32(ldev, LSDC_CRTC1_VSYNC_COUNTER_REG);
> +}
> +
> +/*
> + * The DMA step register is available since ls7a2000/ls2k2000, for support
> + * odd resolutions. But a large DMA step may save bandwidth. Behavior of
> + * writing thoes bits field on ls7a1000/ls2k1000 is underfined.
> + */
> +
> +static void lsdc_crtc0_set_dma_step(struct lsdc_crtc *lcrtc,
> + enum lsdc_dma_steps dma_step)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> + u32 val = lsdc_rreg32(ldev, LSDC_CRTC0_CFG_REG);
> +
> + val &= ~CFG_DMA_STEP_MASK;
> + val |= dma_step << CFG_DMA_STEP_SHIFT;
> +
> + lsdc_wreg32(ldev, LSDC_CRTC0_CFG_REG, val);
> +}
> +
> +static void lsdc_crtc1_set_dma_step(struct lsdc_crtc *lcrtc,
> + enum lsdc_dma_steps dma_step)
> +{
> + struct lsdc_device *ldev = lcrtc->ldev;
> + u32 val = lsdc_rreg32(ldev, LSDC_CRTC1_CFG_REG);
> +
> + val &= ~CFG_DMA_STEP_MASK;
> + val |= dma_step << CFG_DMA_STEP_SHIFT;
> +
> + lsdc_wreg32(ldev, LSDC_CRTC1_CFG_REG, val);
> +}
> +
> +static const struct lsdc_crtc_hw_ops ls7a2000_crtc_hw_ops[2] = {
> + {
> + .enable = lsdc_crtc0_enable,
> + .disable = lsdc_crtc0_disable,
> + .enable_vblank = lsdc_crtc0_enable_vblank,
> + .disable_vblank = lsdc_crtc0_disable_vblank,
> + .flip = lsdc_crtc0_flip,
> + .clone = lsdc_crtc0_clone,
> + .set_mode = lsdc_crtc0_set_mode,
> + .soft_reset = lsdc_crtc0_soft_reset,
> + .get_scan_pos = lsdc_crtc0_scan_pos,
> + .set_dma_step = lsdc_crtc0_set_dma_step,
> + .get_vblank_counter = lsdc_crtc0_get_vblank_count,
> + .reset = lsdc_crtc0_reset,
> + },
> + {
> + .enable = lsdc_crtc1_enable,
> + .disable = lsdc_crtc1_disable,
> + .enable_vblank = lsdc_crtc1_enable_vblank,
> + .disable_vblank = lsdc_crtc1_disable_vblank,
> + .flip = lsdc_crtc1_flip,
> + .clone = lsdc_crtc1_clone,
> + .set_mode = lsdc_crtc1_set_mode,
> + .get_scan_pos = lsdc_crtc1_scan_pos,
> + .soft_reset = lsdc_crtc1_soft_reset,
> + .set_dma_step = lsdc_crtc1_set_dma_step,
> + .get_vblank_counter = lsdc_crtc1_get_vblank_count,
> + .reset = lsdc_crtc1_reset,
> + },
> +};
> +
> +static void lsdc_crtc_reset(struct drm_crtc *crtc)
> +{
> + struct lsdc_crtc *lcrtc = to_lsdc_crtc(crtc);
> + const struct lsdc_crtc_hw_ops *ops = lcrtc->hw_ops;
> + struct lsdc_crtc_state *priv_crtc_state;
> +
> + if (crtc->state)
> + crtc->funcs->atomic_destroy_state(crtc, crtc->state);
> +
> + priv_crtc_state = kzalloc(sizeof(*priv_crtc_state), GFP_KERNEL);
> +
> + if (!priv_crtc_state)
> + __drm_atomic_helper_crtc_reset(crtc, NULL);
> + else
> + __drm_atomic_helper_crtc_reset(crtc, &priv_crtc_state->base);
> +
> + /*
> + * Reset the crtc hardware, this is need for S3 support,
> + * otherwise, wait for vblank timeout
> + */
> + ops->reset(lcrtc);
> +}
> +
> +static void lsdc_crtc_atomic_destroy_state(struct drm_crtc *crtc,
> + struct drm_crtc_state *state)
> +{
> + struct lsdc_crtc_state *priv_state = to_lsdc_crtc_state(state);
> +
> + __drm_atomic_helper_crtc_destroy_state(&priv_state->base);
> +
> + kfree(priv_state);
> +}
> +
> +static struct drm_crtc_state *
> +lsdc_crtc_atomic_duplicate_state(struct drm_crtc *crtc)
> +{
> + struct lsdc_crtc_state *new_priv_state;
> + struct lsdc_crtc_state *old_priv_state;
> +
> + new_priv_state = kzalloc(sizeof(*new_priv_state), GFP_KERNEL);
> + if (!new_priv_state)
> + return NULL;
> +
> + __drm_atomic_helper_crtc_duplicate_state(crtc, &new_priv_state->base);
> +
> + old_priv_state = to_lsdc_crtc_state(crtc->state);
> +
> + memcpy(&new_priv_state->pparms, &old_priv_state->pparms,
> + sizeof(new_priv_state->pparms));
> +
> + return &new_priv_state->base;
> +}
> +
> +static u32 lsdc_crtc_get_vblank_counter(struct drm_crtc *crtc)
> +{
> + struct lsdc_crtc *lcrtc = to_lsdc_crtc(crtc);
> + const struct lsdc_crtc_hw_ops *ops = lcrtc->hw_ops;
> +
> + return ops->get_vblank_counter(lcrtc);
> +}
> +
> +static int lsdc_crtc_enable_vblank(struct drm_crtc *crtc)
> +{
> + struct lsdc_crtc *lcrtc = to_lsdc_crtc(crtc);
> + const struct lsdc_crtc_hw_ops *ops = lcrtc->hw_ops;
> +
> + ops->enable_vblank(lcrtc);
> +
> + return 0;
> +}
> +
> +static void lsdc_crtc_disable_vblank(struct drm_crtc *crtc)
> +{
> + struct lsdc_crtc *lcrtc = to_lsdc_crtc(crtc);
> + const struct lsdc_crtc_hw_ops *ops = lcrtc->hw_ops;
> +
> + ops->disable_vblank(lcrtc);
> +}
> +
> +/* CRTC related debugfs
> + *
> + * Primary planes and cursor planes are also belong to the CRTC for our case,
> + * so also append other registers to here, for sake of convient.
> + */
> +
> +#define REG_DEF(reg) { .name = __stringify_1(LSDC_##reg##_REG), .offset = LSDC_##reg##_REG }
> +
> +static const struct lsdc_reg32 lsdc_crtc_regs_array[2][21] = {
> + [0] = {
> + REG_DEF(CRTC0_CFG),
> + REG_DEF(CRTC0_FB_ORIGIN),
> + REG_DEF(CRTC0_PANEL_CONF),
> + REG_DEF(CRTC0_HDISPLAY),
> + REG_DEF(CRTC0_HSYNC),
> + REG_DEF(CRTC0_VDISPLAY),
> + REG_DEF(CRTC0_VSYNC),
> + REG_DEF(CRTC0_GAMMA_INDEX),
> + REG_DEF(CRTC0_GAMMA_DATA),
> + REG_DEF(CRTC0_SYNC_DEVIATION),
> + REG_DEF(CRTC0_VSYNC_COUNTER),
> + REG_DEF(CRTC0_SCAN_POS),
> + REG_DEF(CRTC0_STRIDE),
> + REG_DEF(CRTC0_FB1_ADDR_HI),
> + REG_DEF(CRTC0_FB1_ADDR_LO),
> + REG_DEF(CRTC0_FB0_ADDR_HI),
> + REG_DEF(CRTC0_FB0_ADDR_LO),
> + REG_DEF(CURSOR0_CFG),
> + REG_DEF(CURSOR0_POSITION),
> + REG_DEF(CURSOR0_BG_COLOR),
> + REG_DEF(CURSOR0_FG_COLOR),
> + },
> + [1] = {
> + REG_DEF(CRTC1_CFG),
> + REG_DEF(CRTC1_FB_ORIGIN),
> + REG_DEF(CRTC1_PANEL_CONF),
> + REG_DEF(CRTC1_HDISPLAY),
> + REG_DEF(CRTC1_HSYNC),
> + REG_DEF(CRTC1_VDISPLAY),
> + REG_DEF(CRTC1_VSYNC),
> + REG_DEF(CRTC1_GAMMA_INDEX),
> + REG_DEF(CRTC1_GAMMA_DATA),
> + REG_DEF(CRTC1_SYNC_DEVIATION),
> + REG_DEF(CRTC1_VSYNC_COUNTER),
> + REG_DEF(CRTC1_SCAN_POS),
> + REG_DEF(CRTC1_STRIDE),
> + REG_DEF(CRTC1_FB1_ADDR_HI),
> + REG_DEF(CRTC1_FB1_ADDR_LO),
> + REG_DEF(CRTC1_FB0_ADDR_HI),
> + REG_DEF(CRTC1_FB0_ADDR_LO),
> + REG_DEF(CURSOR1_CFG),
> + REG_DEF(CURSOR1_POSITION),
> + REG_DEF(CURSOR1_BG_COLOR),
> + REG_DEF(CURSOR1_FG_COLOR),
> + },
> +};
> +
> +static int lsdc_crtc_show_regs(struct seq_file *m, void *arg)
> +{
> + struct drm_info_node *node = (struct drm_info_node *)m->private;
> + struct lsdc_crtc *lcrtc = (struct lsdc_crtc *)node->info_ent->data;
> + struct lsdc_device *ldev = lcrtc->ldev;
> + unsigned int i;
> +
> + for (i = 0; i < lcrtc->nreg; i++) {
> + const struct lsdc_reg32 *preg = &lcrtc->preg[i];
> + u32 offset = preg->offset;
> +
> + seq_printf(m, "%s (0x%04x): 0x%08x\n",
> + preg->name, offset, lsdc_rreg32(ldev, offset));
> + }
> +
> + return 0;
> +}
> +
> +static int lsdc_crtc_show_scan_position(struct seq_file *m, void *arg)
> +{
> + struct drm_info_node *node = (struct drm_info_node *)m->private;
> + struct lsdc_crtc *lcrtc = (struct lsdc_crtc *)node->info_ent->data;
> + const struct lsdc_crtc_hw_ops *ops = lcrtc->hw_ops;
> + int x, y;
> +
> + ops->get_scan_pos(lcrtc, &x, &y);
> +
> + seq_printf(m, "scanout position: x: %08u, y: %08u\n", x, y);
> +
> + return 0;
> +}
> +
> +static int lsdc_crtc_show_vblank_counter(struct seq_file *m, void *arg)
> +{
> + struct drm_info_node *node = (struct drm_info_node *)m->private;
> + struct lsdc_crtc *lcrtc = (struct lsdc_crtc *)node->info_ent->data;
> + const struct lsdc_crtc_hw_ops *ops = lcrtc->hw_ops;
> +
> + seq_printf(m, "CRTC-0 vblank counter: %08u\n\n",
> + ops->get_vblank_counter(lcrtc));
> +
> + return 0;
> +}
> +
> +static int lsdc_pixpll_show_clock(struct seq_file *m, void *arg)
> +{
> + struct drm_info_node *node = (struct drm_info_node *)m->private;
> + struct lsdc_crtc *lcrtc = (struct lsdc_crtc *)node->info_ent->data;
> + struct lsdc_pixpll *pixpll = &lcrtc->pixpll;
> + const struct lsdc_pixpll_funcs *funcs = pixpll->funcs;
> + struct drm_crtc *crtc = &lcrtc->base;
> + struct drm_display_mode *mode = &crtc->state->mode;
> + struct drm_printer printer = drm_seq_file_printer(m);
> + unsigned int out_khz;
> +
> + out_khz = funcs->get_rate(pixpll);
> +
> + seq_printf(m, "%s: %dx%d@%d\n", crtc->name,
> + mode->hdisplay, mode->vdisplay, drm_mode_vrefresh(mode));
> +
> + seq_printf(m, "Pixel clock required: %d kHz\n", mode->clock);
> + seq_printf(m, "Actual frequency output: %u kHz\n", out_khz);
> + seq_printf(m, "Diff: %d kHz\n", out_khz - mode->clock);
> +
> + funcs->print(pixpll, &printer);
> +
> + return 0;
> +}
> +
> +static struct drm_info_list lsdc_crtc_debugfs_list[2][4] = {
> + [0] = {
> + { "regs", lsdc_crtc_show_regs, 0, NULL },
> + { "pixclk", lsdc_pixpll_show_clock, 0, NULL },
> + { "scanpos", lsdc_crtc_show_scan_position, 0, NULL },
> + { "vblanks", lsdc_crtc_show_vblank_counter, 0, NULL },
> + },
> + [1] = {
> + { "regs", lsdc_crtc_show_regs, 0, NULL },
> + { "pixclk", lsdc_pixpll_show_clock, 0, NULL },
> + { "scanpos", lsdc_crtc_show_scan_position, 0, NULL },
> + { "vblanks", lsdc_crtc_show_vblank_counter, 0, NULL },
> + },
> +};
> +
> +/* operate manually */
> +
> +static int lsdc_crtc_man_op_show(struct seq_file *m, void *data)
> +{
> + seq_puts(m, "soft_reset: soft reset this CRTC\n");
> + seq_puts(m, "enable: enable this CRTC\n");
> + seq_puts(m, "disable: disable this CRTC\n");
> + seq_puts(m, "flip: trigger the page flip\n");
> + seq_puts(m, "clone: clone the another crtc with hardware logic\n");
> +
> + return 0;
> +}
> +
> +static int lsdc_crtc_man_op_open(struct inode *inode, struct file *file)
> +{
> + struct drm_crtc *crtc = inode->i_private;
> +
> + return single_open(file, lsdc_crtc_man_op_show, crtc);
> +}
> +
> +static ssize_t lsdc_crtc_man_op_write(struct file *file,
> + const char __user *ubuf,
> + size_t len,
> + loff_t *offp)
Same problem.
> +{
> + struct seq_file *m = file->private_data;
> + struct drm_crtc *crtc = m->private;
> + struct lsdc_crtc *lcrtc = to_lsdc_crtc(crtc);
> + const struct lsdc_crtc_hw_ops *ops = lcrtc->hw_ops;
> +
> + char buf[16];
> +
> + if (len > sizeof(buf) - 1)
> + return -EINVAL;
> +
> + if (copy_from_user(buf, ubuf, len))
> + return -EFAULT;
> +
> + buf[len] = '\0';
> +
> + if (sysfs_streq(buf, "soft_reset"))
> + ops->soft_reset(lcrtc);
> + else if (sysfs_streq(buf, "enable"))
> + ops->enable(lcrtc);
> + else if (sysfs_streq(buf, "disable"))
> + ops->disable(lcrtc);
> + else if (sysfs_streq(buf, "flip"))
> + ops->flip(lcrtc);
> + else if (sysfs_streq(buf, "clone"))
> + ops->clone(lcrtc);
> +
> + return len;
> +}
> +
> +static const struct file_operations lsdc_crtc_man_op_fops = {
> + .owner = THIS_MODULE,
> + .open = lsdc_crtc_man_op_open,
> + .read = seq_read,
> + .llseek = seq_lseek,
> + .release = single_release,
> + .write = lsdc_crtc_man_op_write,
> +};
> +
> +static int lsdc_crtc_late_register(struct drm_crtc *crtc)
> +{
> + struct lsdc_display_pipe *dispipe = crtc_to_display_pipe(crtc);
> + struct lsdc_crtc *lcrtc = to_lsdc_crtc(crtc);
> + struct drm_minor *minor = crtc->dev->primary;
> + unsigned int index = dispipe->index;
> + unsigned int i;
> +
> + lcrtc->preg = lsdc_crtc_regs_array[index];
> + lcrtc->nreg = ARRAY_SIZE(lsdc_crtc_regs_array[index]);
> + lcrtc->p_info_list = lsdc_crtc_debugfs_list[index];
> + lcrtc->n_info_list = ARRAY_SIZE(lsdc_crtc_debugfs_list[index]);
> +
> + for (i = 0; i < lcrtc->n_info_list; ++i)
> + lcrtc->p_info_list[i].data = lcrtc;
> +
> + drm_debugfs_create_files(lcrtc->p_info_list,
> + lcrtc->n_info_list,
> + crtc->debugfs_entry,
> + minor);
> +
> + /* supported manual operations */
> + debugfs_create_file("ops", 0644, crtc->debugfs_entry, crtc,
> + &lsdc_crtc_man_op_fops);
> +
> + return 0;
> +}
> +
> +static void lsdc_crtc_atomic_print_state(struct drm_printer *p,
> + const struct drm_crtc_state *state)
> +{
> + const struct lsdc_crtc_state *priv_state;
> + const struct lsdc_pixpll_parms *pparms;
> +
> + priv_state = container_of_const(state, struct lsdc_crtc_state, base);
> + pparms = &priv_state->pparms;
> +
> + drm_printf(p, "\tInput clock divider = %u\n", pparms->div_ref);
> + drm_printf(p, "\tMedium clock Multiplier = %u\n", pparms->loopc);
> + drm_printf(p, "\tOutput clock divider = %u\n", pparms->div_out);
> +}
> +
> +static const struct drm_crtc_funcs ls7a1000_crtc_funcs = {
> + .reset = lsdc_crtc_reset,
> + .destroy = drm_crtc_cleanup,
> + .set_config = drm_atomic_helper_set_config,
> + .page_flip = drm_atomic_helper_page_flip,
> + .atomic_duplicate_state = lsdc_crtc_atomic_duplicate_state,
> + .atomic_destroy_state = lsdc_crtc_atomic_destroy_state,
> + .late_register = lsdc_crtc_late_register,
> + .enable_vblank = lsdc_crtc_enable_vblank,
> + .disable_vblank = lsdc_crtc_disable_vblank,
> + .get_vblank_timestamp = drm_crtc_vblank_helper_get_vblank_timestamp,
> + .atomic_print_state = lsdc_crtc_atomic_print_state,
> +};
> +
> +static const struct drm_crtc_funcs ls7a2000_crtc_funcs = {
> + .reset = lsdc_crtc_reset,
> + .destroy = drm_crtc_cleanup,
> + .set_config = drm_atomic_helper_set_config,
> + .page_flip = drm_atomic_helper_page_flip,
> + .atomic_duplicate_state = lsdc_crtc_atomic_duplicate_state,
> + .atomic_destroy_state = lsdc_crtc_atomic_destroy_state,
> + .late_register = lsdc_crtc_late_register,
> + .get_vblank_counter = lsdc_crtc_get_vblank_counter,
> + .enable_vblank = lsdc_crtc_enable_vblank,
> + .disable_vblank = lsdc_crtc_disable_vblank,
> + .get_vblank_timestamp = drm_crtc_vblank_helper_get_vblank_timestamp,
> + .atomic_print_state = lsdc_crtc_atomic_print_state,
> +};
> +
> +static enum drm_mode_status
> +lsdc_crtc_mode_valid(struct drm_crtc *crtc, const struct drm_display_mode *mode)
> +{
> + struct drm_device *ddev = crtc->dev;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + const struct lsdc_desc *descp = ldev->descp;
> + unsigned int pitch;
> +
> + if (mode->hdisplay > descp->max_width)
> + return MODE_BAD_HVALUE;
> +
> + if (mode->vdisplay > descp->max_height)
> + return MODE_BAD_VVALUE;
> +
> + if (mode->clock > descp->max_pixel_clk) {
> + drm_dbg_kms(ddev, "mode %dx%d, pixel clock=%d is too high\n",
> + mode->hdisplay, mode->vdisplay, mode->clock);
> + return MODE_CLOCK_HIGH;
> + }
> +
> + /* 4 for DRM_FORMAT_XRGB8888 */
> + pitch = mode->hdisplay * 4;
> +
> + if (pitch % descp->pitch_align) {
> + drm_dbg_kms(ddev, "aligned to %u bytes is required: %u\n",
> + descp->pitch_align, pitch);
> + return MODE_BAD_WIDTH;
> + }
> +
> + return MODE_OK;
> +}
> +
> +static int lsdc_pixpll_atomic_check(struct drm_crtc *crtc,
> + struct drm_crtc_state *state)
> +{
> + struct lsdc_crtc *lcrtc = to_lsdc_crtc(crtc);
> + struct lsdc_pixpll *pixpll = &lcrtc->pixpll;
> + const struct lsdc_pixpll_funcs *pfuncs = pixpll->funcs;
> + struct lsdc_crtc_state *priv_state = to_lsdc_crtc_state(state);
> + unsigned int clock = state->mode.clock;
> + int ret;
> +
> + ret = pfuncs->compute(pixpll, clock, &priv_state->pparms);
> + if (ret) {
> + drm_warn(crtc->dev, "find PLL parms for %ukHz failed\n", clock);
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int lsdc_crtc_helper_atomic_check(struct drm_crtc *crtc,
> + struct drm_atomic_state *state)
> +{
> + struct drm_crtc_state *crtc_state = drm_atomic_get_new_crtc_state(state, crtc);
> +
> + if (!crtc_state->enable)
> + return 0;
> +
> + return lsdc_pixpll_atomic_check(crtc, crtc_state);
> +}
> +
> +static void lsdc_crtc_mode_set_nofb(struct drm_crtc *crtc)
> +{
> + struct lsdc_crtc *lcrtc = to_lsdc_crtc(crtc);
> + const struct lsdc_crtc_hw_ops *crtc_hw_ops = lcrtc->hw_ops;
> + struct lsdc_pixpll *pixpll = &lcrtc->pixpll;
> + const struct lsdc_pixpll_funcs *pixpll_funcs = pixpll->funcs;
> + struct drm_crtc_state *state = crtc->state;
> + struct drm_display_mode *mode = &state->mode;
> + struct lsdc_crtc_state *priv_state = to_lsdc_crtc_state(state);
> +
> + pixpll_funcs->update(pixpll, &priv_state->pparms);
> +
> + if (crtc_hw_ops->set_dma_step) {
> + unsigned int width_in_bytes = mode->hdisplay * 4;
> + enum lsdc_dma_steps dma_step;
> +
> + /*
> + * Using large dma step as much as possible, for improving
> + * hardware DMA efficiency.
> + */
> + if (width_in_bytes % 256 == 0)
> + dma_step = LSDC_DMA_STEP_256_BYTES;
> + else if (width_in_bytes % 128 == 0)
> + dma_step = LSDC_DMA_STEP_128_BYTES;
> + else if (width_in_bytes % 64 == 0)
> + dma_step = LSDC_DMA_STEP_64_BYTES;
> + else /* width_in_bytes % 32 == 0 */
> + dma_step = LSDC_DMA_STEP_32_BYTES;
> +
> + crtc_hw_ops->set_dma_step(lcrtc, dma_step);
> + }
> +
> + crtc_hw_ops->set_mode(lcrtc, mode);
> +}
> +
> +static void lsdc_crtc_send_vblank(struct drm_crtc *crtc)
> +{
> + struct drm_device *ddev = crtc->dev;
> + unsigned long flags;
> +
> + if (!crtc->state || !crtc->state->event)
> + return;
> +
> + drm_dbg(ddev, "send vblank manually\n");
> +
> + spin_lock_irqsave(&ddev->event_lock, flags);
> + drm_crtc_send_vblank_event(crtc, crtc->state->event);
> + crtc->state->event = NULL;
> + spin_unlock_irqrestore(&ddev->event_lock, flags);
> +}
> +
> +static void lsdc_crtc_atomic_enable(struct drm_crtc *crtc,
> + struct drm_atomic_state *state)
> +{
> + struct lsdc_crtc *lcrtc = to_lsdc_crtc(crtc);
> + const struct lsdc_crtc_hw_ops *ops = lcrtc->hw_ops;
> +
> + drm_crtc_vblank_on(crtc);
> +
> + drm_dbg(crtc->dev, "%s enable\n", crtc->name);
> +
> + ops->enable(lcrtc);
> +}
> +
> +static void lsdc_crtc_atomic_disable(struct drm_crtc *crtc,
> + struct drm_atomic_state *state)
> +{
> + struct lsdc_crtc *lcrtc = to_lsdc_crtc(crtc);
> + const struct lsdc_crtc_hw_ops *ops = lcrtc->hw_ops;
> +
> + drm_crtc_vblank_off(crtc);
> +
> + ops->disable(lcrtc);
> +
> + drm_dbg(crtc->dev, "%s disable\n", crtc->name);
> +
> + /*
> + * Make sure we issue a vblank event after disabling the CRTC if
> + * someone was waiting it.
> + */
> + lsdc_crtc_send_vblank(crtc);
> +}
> +
> +static void lsdc_crtc_atomic_flush(struct drm_crtc *crtc,
> + struct drm_atomic_state *state)
> +{
> + spin_lock_irq(&crtc->dev->event_lock);
> + if (crtc->state->event) {
> + if (drm_crtc_vblank_get(crtc) == 0)
> + drm_crtc_arm_vblank_event(crtc, crtc->state->event);
> + else
> + drm_crtc_send_vblank_event(crtc, crtc->state->event);
> + crtc->state->event = NULL;
> + }
> + spin_unlock_irq(&crtc->dev->event_lock);
> +}
> +
> +static bool lsdc_crtc_get_scanout_position(struct drm_crtc *crtc,
> + bool in_vblank_irq,
> + int *vpos,
> + int *hpos,
> + ktime_t *stime,
> + ktime_t *etime,
> + const struct drm_display_mode *mode)
> +{
> + struct lsdc_crtc *lcrtc = to_lsdc_crtc(crtc);
> + const struct lsdc_crtc_hw_ops *ops = lcrtc->hw_ops;
> + int vsw, vbp, vactive_start, vactive_end, vfp_end;
> + int x, y;
> +
> + vsw = mode->crtc_vsync_end - mode->crtc_vsync_start;
> + vbp = mode->crtc_vtotal - mode->crtc_vsync_end;
> +
> + vactive_start = vsw + vbp + 1;
> + vactive_end = vactive_start + mode->crtc_vdisplay;
> +
> + /* last scan line before VSYNC */
> + vfp_end = mode->crtc_vtotal;
> +
> + if (stime)
> + *stime = ktime_get();
> +
> + ops->get_scan_pos(lcrtc, &x, &y);
> +
> + if (y > vactive_end)
> + y = y - vfp_end - vactive_start;
> + else
> + y -= vactive_start;
> +
> + *vpos = y;
> + *hpos = x;
> +
> + if (etime)
> + *etime = ktime_get();
> +
> + return true;
> +}
> +
> +static const struct drm_crtc_helper_funcs lsdc_crtc_helper_funcs = {
> + .mode_valid = lsdc_crtc_mode_valid,
> + .mode_set_nofb = lsdc_crtc_mode_set_nofb,
> + .atomic_enable = lsdc_crtc_atomic_enable,
> + .atomic_disable = lsdc_crtc_atomic_disable,
> + .atomic_check = lsdc_crtc_helper_atomic_check,
> + .atomic_flush = lsdc_crtc_atomic_flush,
> + .get_scanout_position = lsdc_crtc_get_scanout_position,
> +};
> +
> +int ls7a1000_crtc_init(struct drm_device *ddev,
> + struct drm_crtc *crtc,
> + struct drm_plane *primary,
> + struct drm_plane *cursor,
> + unsigned int index)
> +{
> + struct lsdc_crtc *lcrtc = to_lsdc_crtc(crtc);
> + int ret;
> +
> + ret = lsdc_pixpll_init(&lcrtc->pixpll, ddev, index);
> + if (ret) {
> + drm_err(ddev, "crtc init with pll failed: %d\n", ret);
> + return ret;
> + }
> +
> + lcrtc->ldev = to_lsdc(ddev);
> + lcrtc->hw_ops = &ls7a1000_crtc_hw_ops[index];
> +
> + ret = drm_crtc_init_with_planes(ddev,
> + crtc,
> + primary,
> + cursor,
> + &ls7a1000_crtc_funcs,
> + "CRTC-%d",
> + index);
> + if (ret) {
> + drm_err(ddev, "crtc init with planes failed: %d\n", ret);
> + return ret;
> + }
> +
> + drm_crtc_helper_add(crtc, &lsdc_crtc_helper_funcs);
> +
> + ret = drm_mode_crtc_set_gamma_size(crtc, 256);
> + if (ret)
> + return ret;
> +
> + drm_crtc_enable_color_mgmt(crtc, 0, false, 256);
> +
> + return 0;
> +}
> +
> +int ls7a2000_crtc_init(struct drm_device *ddev,
> + struct drm_crtc *crtc,
> + struct drm_plane *primary,
> + struct drm_plane *cursor,
> + unsigned int index)
> +{
> + struct lsdc_crtc *lcrtc = to_lsdc_crtc(crtc);
> + int ret;
> +
> + ret = lsdc_pixpll_init(&lcrtc->pixpll, ddev, index);
> + if (ret) {
> + drm_err(ddev, "crtc init with pll failed: %d\n", ret);
> + return ret;
> + }
> +
> + lcrtc->ldev = to_lsdc(ddev);
> + lcrtc->hw_ops = &ls7a2000_crtc_hw_ops[index];
> +
> + ret = drm_crtc_init_with_planes(ddev,
> + crtc,
> + primary,
> + cursor,
> + &ls7a2000_crtc_funcs,
> + "CRTC-%d",
> + index);
Same problem.
> + if (ret) {
> + drm_err(ddev, "crtc init with planes failed: %d\n", ret);
> + return ret;
> + }
> +
> + drm_crtc_helper_add(crtc, &lsdc_crtc_helper_funcs);
> +
> + ret = drm_mode_crtc_set_gamma_size(crtc, 256);
> + if (ret)
> + return ret;
> +
> + drm_crtc_enable_color_mgmt(crtc, 0, false, 256);
> +
> + return 0;
> +}
> diff --git a/drivers/gpu/drm/loongson/lsdc_debugfs.c b/drivers/gpu/drm/loongson/lsdc_debugfs.c
> new file mode 100644
> index 000000000000..30d70a5dc7d5
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_debugfs.c
> @@ -0,0 +1,78 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#include <drm/drm_debugfs.h>
> +
> +#include "lsdc_drv.h"
> +#include "lsdc_gem.h"
> +#include "lsdc_probe.h"
> +#include "lsdc_ttm.h"
> +
> +/* device level debugfs */
> +
> +static int lsdc_identify(struct seq_file *m, void *arg)
> +{
> + struct drm_info_node *node = (struct drm_info_node *)m->private;
> + struct lsdc_device *ldev = (struct lsdc_device *)node->info_ent->data;
> + const struct loongson_gfx_desc *gfx = to_loongson_gfx(ldev->descp);
> + u8 impl, rev;
> +
> + loongson_cpu_get_prid(&impl, &rev);
> +
> + seq_printf(m, "Running on cpu 0x%x, cpu revision: 0x%x\n",
> + impl, rev);
> +
> + seq_printf(m, "Contained in: %s\n", gfx->model);
> +
> + return 0;
> +}
> +
> +static int lsdc_show_mm(struct seq_file *m, void *arg)
> +{
> + struct drm_info_node *node = (struct drm_info_node *)m->private;
> + struct drm_device *ddev = node->minor->dev;
> + struct drm_printer p = drm_seq_file_printer(m);
> +
> + drm_mm_print(&ddev->vma_offset_manager->vm_addr_space_mm, &p);
> +
> + return 0;
> +}
> +
> +static int loongson_gfxpll_show_clock(struct seq_file *m, void *arg)
> +{
> + struct drm_info_node *node = (struct drm_info_node *)m->private;
> + struct lsdc_device *ldev = (struct lsdc_device *)node->info_ent->data;
> + struct drm_printer printer = drm_seq_file_printer(m);
> + struct loongson_gfxpll *gfxpll = ldev->gfxpll;
> +
> + gfxpll->funcs->print(gfxpll, &printer, true);
> +
> + return 0;
> +}
> +
> +static struct drm_info_list lsdc_debugfs_list[] = {
> + { "chips", lsdc_identify, 0, NULL },
> + { "clocks", loongson_gfxpll_show_clock, 0, NULL },
> + { "mm", lsdc_show_mm, 0, NULL },
> + { "bos", lsdc_show_buffer_object, 0, NULL },
> +};
> +
> +void lsdc_debugfs_init(struct drm_minor *minor)
> +{
> + struct drm_device *ddev = minor->dev;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + unsigned int N = ARRAY_SIZE(lsdc_debugfs_list);
> + unsigned int i;
> +
> + for (i = 0; i < N; ++i)
> + lsdc_debugfs_list[i].data = ldev;
> +
> + drm_debugfs_create_files(lsdc_debugfs_list,
> + N,
> + minor->debugfs_root,
> + minor);
> +
> + lsdc_ttm_debugfs_init(ldev);
> +}
> diff --git a/drivers/gpu/drm/loongson/lsdc_device.c b/drivers/gpu/drm/loongson/lsdc_device.c
> new file mode 100644
> index 000000000000..e2dd0e357fa2
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_device.c
> @@ -0,0 +1,104 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#include <linux/pci.h>
> +
> +#include "lsdc_drv.h"
> +
> +static const struct lsdc_kms_funcs ls7a1000_kms_funcs = {
> + .create_i2c = lsdc_create_i2c_chan,
> + .irq_handler = ls7a1000_dc_irq_handler,
> + .output_init = ls7a1000_output_init,
> + .cursor_plane_init = ls7a1000_cursor_plane_init,
> + .primary_plane_init = lsdc_primary_plane_init,
> + .crtc_init = ls7a1000_crtc_init,
> +};
> +
> +static const struct lsdc_kms_funcs ls7a2000_kms_funcs = {
> + .create_i2c = lsdc_create_i2c_chan,
> + .irq_handler = ls7a2000_dc_irq_handler,
> + .output_init = ls7a2000_output_init,
> + .cursor_plane_init = ls7a2000_cursor_plane_init,
> + .primary_plane_init = lsdc_primary_plane_init,
> + .crtc_init = ls7a2000_crtc_init,
> +};
> +
> +static const struct loongson_gfx_desc ls7a1000_gfx = {
> + .dc = {
> + .num_of_crtc = 2,
> + .max_pixel_clk = 200000,
> + .max_width = 2048,
> + .max_height = 2048,
> + .num_of_hw_cursor = 1,
> + .hw_cursor_w = 32,
> + .hw_cursor_h = 32,
> + .pitch_align = 256,
> + .mc_bits = 40,
> + .has_vblank_counter = false,
> + .funcs = &ls7a1000_kms_funcs,
> + },
> + .conf_reg_base = LS7A1000_CONF_REG_BASE,
> + .gfxpll = {
> + .reg_offset = LS7A1000_PLL_GFX_REG,
> + .reg_size = 8,
> + },
> + .pixpll = {
> + [0] = {
> + .reg_offset = LS7A1000_PIXPLL0_REG,
> + .reg_size = 8,
> + },
> + [1] = {
> + .reg_offset = LS7A1000_PIXPLL1_REG,
> + .reg_size = 8,
> + },
> + },
> + .chip_id = CHIP_LS7A1000,
> + .model = "LS7A1000 bridge chipset",
> +};
> +
> +static const struct loongson_gfx_desc ls7a2000_gfx = {
> + .dc = {
> + .num_of_crtc = 2,
> + .max_pixel_clk = 350000,
> + .max_width = 4096,
> + .max_height = 4096,
> + .num_of_hw_cursor = 2,
> + .hw_cursor_w = 64,
> + .hw_cursor_h = 64,
> + .pitch_align = 64,
> + .mc_bits = 40, /* Support 48 but using 40 for backward compatibility */
> + .has_vblank_counter = true,
> + .funcs = &ls7a2000_kms_funcs,
> + },
> + .conf_reg_base = LS7A2000_CONF_REG_BASE,
> + .gfxpll = {
> + .reg_offset = LS7A2000_PLL_GFX_REG,
> + .reg_size = 8,
> + },
> + .pixpll = {
> + [0] = {
> + .reg_offset = LS7A2000_PIXPLL0_REG,
> + .reg_size = 8,
> + },
> + [1] = {
> + .reg_offset = LS7A2000_PIXPLL1_REG,
> + .reg_size = 8,
> + },
> + },
> + .chip_id = CHIP_LS7A2000,
> + .model = "LS7A2000 bridge chipset",
> +};
> +
> +const struct lsdc_desc *
> +lsdc_device_probe(struct pci_dev *pdev, enum loongson_chip_id chip_id)
> +{
> + if (chip_id == CHIP_LS7A1000)
> + return &ls7a1000_gfx.dc;
> +
> + if (chip_id == CHIP_LS7A2000)
> + return &ls7a2000_gfx.dc;
> +
> + return ERR_PTR(-ENODEV);
> +}
> diff --git a/drivers/gpu/drm/loongson/lsdc_drv.c b/drivers/gpu/drm/loongson/lsdc_drv.c
> new file mode 100644
> index 000000000000..a91db7fe33c8
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_drv.c
> @@ -0,0 +1,484 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#include <linux/pci.h>
> +
> +#include <video/nomodeset.h>
> +
> +#include <drm/drm_aperture.h>
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_drv.h>
> +#include <drm/drm_fbdev_generic.h>
> +#include <drm/drm_gem_framebuffer_helper.h>
> +#include <drm/drm_ioctl.h>
> +#include <drm/drm_modeset_helper.h>
> +#include <drm/drm_probe_helper.h>
> +#include <drm/drm_vblank.h>
> +
> +#include "lsdc_drv.h"
> +#include "lsdc_gem.h"
> +#include "lsdc_i2c.h"
> +#include "lsdc_irq.h"
> +#include "lsdc_output.h"
> +#include "lsdc_probe.h"
> +#include "lsdc_ttm.h"
> +
> +#define DRIVER_AUTHOR "Sui Jingfeng <suijingfeng@...ngson.cn>"
> +#define DRIVER_NAME "loongson"
> +#define DRIVER_DESC "drm driver for loongson graphics"
> +#define DRIVER_DATE "20220701"
> +#define DRIVER_MAJOR 1
> +#define DRIVER_MINOR 0
> +#define DRIVER_PATCHLEVEL 0
> +
> +DEFINE_DRM_GEM_FOPS(lsdc_gem_fops);
> +
> +static const struct drm_driver lsdc_drm_driver = {
> + .driver_features = DRIVER_MODESET | DRIVER_RENDER | DRIVER_GEM | DRIVER_ATOMIC,
> + .fops = &lsdc_gem_fops,
> +
> + .name = DRIVER_NAME,
> + .desc = DRIVER_DESC,
> + .date = DRIVER_DATE,
> + .major = DRIVER_MAJOR,
> + .minor = DRIVER_MINOR,
> + .patchlevel = DRIVER_PATCHLEVEL,
> +
> + .debugfs_init = lsdc_debugfs_init,
> + .dumb_create = lsdc_dumb_create,
> + .dumb_map_offset = lsdc_dumb_map_offset,
> + .prime_handle_to_fd = drm_gem_prime_handle_to_fd,
> + .prime_fd_to_handle = drm_gem_prime_fd_to_handle,
> + .gem_prime_import_sg_table = lsdc_prime_import_sg_table,
> + .gem_prime_mmap = drm_gem_prime_mmap,
> +};
> +
> +static const struct drm_mode_config_funcs lsdc_mode_config_funcs = {
> + .fb_create = drm_gem_fb_create,
> + .atomic_check = drm_atomic_helper_check,
> + .atomic_commit = drm_atomic_helper_commit,
> +};
> +
> +/* Display related */
> +
> +static int lsdc_modeset_init(struct lsdc_device *ldev,
> + unsigned int num_crtc,
> + const struct lsdc_kms_funcs *funcs)
> +{
> + struct drm_device *ddev = &ldev->base;
> + struct lsdc_display_pipe *dispipe;
> + unsigned int i;
> + int ret;
> +
> + for (i = 0; i < num_crtc; i++) {
> + dispipe = &ldev->dispipe[i];
> +
> + /* We need a index before crtc is initialized */
> + dispipe->index = i;
> +
> + ret = funcs->create_i2c(ddev, dispipe, i);
> + if (ret)
> + return ret;
> + }
> +
> + for (i = 0; i < num_crtc; i++) {
> + struct i2c_adapter *ddc = NULL;
> +
> + dispipe = &ldev->dispipe[i];
> + if (dispipe->li2c)
> + ddc = &dispipe->li2c->adapter;
> +
> + ret = funcs->output_init(ddev, dispipe, ddc, i);
> + if (ret)
> + return ret;
> +
> + ldev->num_output++;
> + }
> +
> + for (i = 0; i < num_crtc; i++) {
> + dispipe = &ldev->dispipe[i];
> +
> + ret = funcs->primary_plane_init(ddev, &dispipe->primary.base, i);
> + if (ret)
> + return ret;
> +
> + ret = funcs->cursor_plane_init(ddev, &dispipe->cursor.base, i);
> + if (ret)
> + return ret;
> +
> + ret = funcs->crtc_init(ddev,
> + &dispipe->crtc.base,
> + &dispipe->primary.base,
> + &dispipe->cursor.base,
> + i);
> + if (ret)
> + return ret;
> + }
> +
> + drm_info(ddev, "total %u outputs\n", ldev->num_output);
> +
> + return 0;
> +}
> +
> +static int lsdc_mode_config_init(struct drm_device *ddev,
> + const struct lsdc_desc *descp)
> +{
> + int ret;
> +
> + ret = drmm_mode_config_init(ddev);
> + if (ret)
> + return ret;
> +
> + ddev->mode_config.funcs = &lsdc_mode_config_funcs;
> + ddev->mode_config.min_width = 1;
> + ddev->mode_config.min_height = 1;
> + ddev->mode_config.max_width = descp->max_width * LSDC_NUM_CRTC;
> + ddev->mode_config.max_height = descp->max_height * LSDC_NUM_CRTC;
> + ddev->mode_config.preferred_depth = 24;
> + ddev->mode_config.prefer_shadow = 1;
> +
> + ddev->mode_config.cursor_width = descp->hw_cursor_h;
> + ddev->mode_config.cursor_height = descp->hw_cursor_h;
> +
> + if (descp->has_vblank_counter)
> + ddev->max_vblank_count = 0xffffffff;
> +
> + return ret;
> +}
> +
> +/*
> + * The GPU and display controller in LS7A1000/LS7A2000 are separated
> + * PCIE devices, they are two devices not one. The DC does not has a
> + * dedicate VRAM bar, because the BIOS engineer choose to assign the
> + * VRAM to the GPU device. Sadly, after years application, this form
> + * as a convention for loongson integrated graphics. Bar 2 of the GPU
> + * device contain the base address and size of the VRAM, both the GPU
> + * and the DC can access the on-board VRAM as long as the DMA address
> + * emitted fall in [base, base + size).
> + */
> +static int lsdc_get_dedicated_vram(struct lsdc_device *ldev,
> + struct pci_dev *pdev_dc,
> + const struct lsdc_desc *descp)
> +{
> + struct drm_device *ddev = &ldev->base;
> + struct pci_dev *pdev_gpu;
> + resource_size_t base, size;
> +
> + /*
> + * The GPU has 00:06.0 as its BDF, while the DC has 00:06.1,
> + * This is sure for LS7A1000, LS7A2000 and LS2K2000.
> + */
> + pdev_gpu = pci_get_domain_bus_and_slot(pci_domain_nr(pdev_dc->bus),
> + pdev_dc->bus->number,
> + PCI_DEVFN(6, 0));
> + if (!pdev_gpu) {
> + drm_err(ddev, "No GPU device, then no VRAM\n");
> + return -ENODEV;
> + }
> +
> + base = pci_resource_start(pdev_gpu, 2);
> + size = pci_resource_len(pdev_gpu, 2);
> +
> + ldev->vram_base = base;
> + ldev->vram_size = size;
> + ldev->gpu = pdev_gpu;
> +
> + drm_info(ddev, "dedicated vram start: 0x%llx, size: %uMB\n",
> + (u64)base, (u32)(size >> 20));
> +
> + return 0;
> +}
> +
> +static struct lsdc_device *
> +lsdc_create_device(struct pci_dev *pdev,
> + const struct lsdc_desc *descp,
> + const struct drm_driver *drv)
> +{
> + struct lsdc_device *ldev;
> + struct drm_device *ddev;
> + int ret;
> +
> + ldev = devm_drm_dev_alloc(&pdev->dev, drv, struct lsdc_device, base);
> + if (IS_ERR(ldev))
> + return ldev;
> +
> + ddev = &ldev->base;
> +
> + ldev->descp = descp;
> +
> + loongson_gfxpll_create(ddev, &ldev->gfxpll);
> +
> + ret = lsdc_get_dedicated_vram(ldev, pdev, descp);
> + if (ret) {
> + drm_err(ddev, "Init VRAM failed: %d\n", ret);
> + return ERR_PTR(ret);
> + }
> +
> + ret = drm_aperture_remove_conflicting_framebuffers(ldev->vram_base,
> + ldev->vram_size,
> + drv);
> + if (ret) {
> + drm_err(ddev, "remove firmware framebuffers failed: %d\n", ret);
> + return ERR_PTR(ret);
> + }
> +
> + ret = lsdc_ttm_init(ldev);
> + if (ret) {
> + drm_err(ddev, "memory manager init failed: %d\n", ret);
> + return ERR_PTR(ret);
> + }
> +
> + lsdc_gem_init(ddev);
> +
> + /* BAR 0 of the DC device contain registers base address */
> + ldev->reg_base = pcim_iomap(pdev, 0, 0);
> + if (!ldev->reg_base)
> + return ERR_PTR(-ENODEV);
> +
> + spin_lock_init(&ldev->reglock);
> +
> + ret = lsdc_mode_config_init(ddev, descp);
> + if (ret)
> + return ERR_PTR(ret);
> +
> + ret = lsdc_modeset_init(ldev, descp->num_of_crtc, descp->funcs);
> + if (ret)
> + return ERR_PTR(ret);
> +
> + drm_mode_config_reset(ddev);
> +
> + ret = drm_vblank_init(ddev, descp->num_of_crtc);
> + if (ret)
> + return ERR_PTR(ret);
> +
> + drm_kms_helper_poll_init(ddev);
> +
> + return ldev;
> +}
> +
> +static int lsdc_pci_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
> +{
> + const struct lsdc_desc *descp;
> + struct drm_device *ddev;
> + struct lsdc_device *ldev;
> + int ret;
> +
> + ret = pcim_enable_device(pdev);
> + if (ret)
> + return ret;
> +
> + pci_set_master(pdev);
> +
> + ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(40));
> + if (ret)
> + return ret;
> +
> + descp = lsdc_device_probe(pdev, ent->driver_data);
> + if (IS_ERR_OR_NULL(descp))
> + return -ENODEV;
> +
> + dev_info(&pdev->dev, "Found %s, revision: %u",
> + to_loongson_gfx(descp)->model, pdev->revision);
> +
> + ldev = lsdc_create_device(pdev, descp, &lsdc_drm_driver);
> + if (IS_ERR(ldev))
> + return PTR_ERR(ldev);
> +
> + ldev->dc = pdev;
> +
> + ddev = &ldev->base;
> +
> + pci_set_drvdata(pdev, ddev);
> +
> + ret = devm_request_irq(&pdev->dev,
> + pdev->irq,
> + descp->funcs->irq_handler,
> + IRQF_SHARED,
> + dev_name(&pdev->dev),
> + ddev);
> + if (ret) {
> + drm_err(ddev, "Failed to register interrupt: %d\n", ret);
> + return ret;
> + }
> +
> + ret = drm_dev_register(ddev, 0);
> + if (ret)
> + return ret;
> +
> + drm_fbdev_generic_setup(ddev, 32);
> +
> + return 0;
> +}
> +
> +static void lsdc_pci_remove(struct pci_dev *pdev)
> +{
> + struct drm_device *ddev = pci_get_drvdata(pdev);
> +
> + drm_dev_unregister(ddev);
> + drm_atomic_helper_shutdown(ddev);
> +}
> +
> +static int lsdc_drm_freeze(struct drm_device *ddev)
> +{
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + struct lsdc_bo *lbo;
> + int ret;
> +
> + /* unpin all of buffers in the vram */
> + mutex_lock(&ldev->gem.mutex);
> + list_for_each_entry(lbo, &ldev->gem.objects, list) {
> + struct ttm_buffer_object *tbo = &lbo->tbo;
> + struct ttm_resource *resource = tbo->resource;
> + unsigned int pin_count = tbo->pin_count;
> +
> + drm_dbg(ddev,
> + "bo[%p], size: %zuKB, type: %s, pin count: %u\n",
> + lbo,
> + lsdc_bo_size(lbo) >> 10,
> + lsdc_mem_type_to_str(resource->mem_type),
> + pin_count);
> +
> + if (!pin_count)
> + continue;
> +
> + if (resource->mem_type == TTM_PL_VRAM) {
> + ret = lsdc_bo_reserve(lbo);
> + if (unlikely(ret)) {
> + drm_err(ddev, "bo reserve failed: %d\n", ret);
> + continue;
> + }
> +
> + /*
> + * For double screen usage case, multiple crtc may
> + * reference to the single giant framebuffer bo.
> + * The single giant fb bo get pinned by multiple time.
> + * thus, it need to unpin until its pin counter reach
> + * zero.
> + */
> + do {
> + lsdc_bo_unpin(lbo);
> + --pin_count;
> + } while (pin_count);
> +
> + lsdc_bo_unreserve(lbo);
> + }
> + }
> + mutex_unlock(&ldev->gem.mutex);
> +
> + lsdc_bo_evict_vram(ddev);
> +
> + ret = drm_mode_config_helper_suspend(ddev);
> + if (unlikely(ret)) {
> + drm_err(ddev, "freeze error: %d", ret);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int lsdc_drm_resume(struct device *dev)
> +{
> + struct pci_dev *pdev = to_pci_dev(dev);
> + struct drm_device *ddev = pci_get_drvdata(pdev);
> +
> + return drm_mode_config_helper_resume(ddev);
> +}
> +
> +static int lsdc_pm_freeze(struct device *dev)
> +{
> + struct pci_dev *pdev = to_pci_dev(dev);
> + struct drm_device *ddev = pci_get_drvdata(pdev);
> +
> + return lsdc_drm_freeze(ddev);
> +}
> +
> +static int lsdc_pm_thaw(struct device *dev)
> +{
> + return lsdc_drm_resume(dev);
> +}
> +
> +static int lsdc_pm_suspend(struct device *dev)
> +{
> + struct pci_dev *pdev = to_pci_dev(dev);
> + int error;
> +
> + error = lsdc_pm_freeze(dev);
> + if (error)
> + return error;
> +
> + pci_save_state(pdev);
> + /* Shut down the device */
> + pci_disable_device(pdev);
> + pci_set_power_state(pdev, PCI_D3hot);
> +
> + return 0;
> +}
> +
> +static int lsdc_pm_resume(struct device *dev)
> +{
> + struct pci_dev *pdev = to_pci_dev(dev);
> +
> + pci_set_power_state(pdev, PCI_D0);
> +
> + pci_restore_state(pdev);
> +
> + if (pcim_enable_device(pdev))
> + return -EIO;
> +
> + return lsdc_pm_thaw(dev);
> +}
> +
> +static const struct dev_pm_ops lsdc_pm_ops = {
> + .suspend = lsdc_pm_suspend,
> + .resume = lsdc_pm_resume,
> + .freeze = lsdc_pm_freeze,
> + .thaw = lsdc_pm_thaw,
> + .poweroff = lsdc_pm_freeze,
> + .restore = lsdc_pm_resume,
> +};
> +
> +static const struct pci_device_id lsdc_pciid_list[] = {
> + {PCI_VENDOR_ID_LOONGSON, 0x7a06, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_LS7A1000},
> + {PCI_VENDOR_ID_LOONGSON, 0x7a36, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_LS7A2000},
> + {0, 0, 0, 0, 0, 0, 0}
> +};
> +
> +static struct pci_driver lsdc_pci_driver = {
> + .name = DRIVER_NAME,
> + .id_table = lsdc_pciid_list,
> + .probe = lsdc_pci_probe,
> + .remove = lsdc_pci_remove,
> + .driver.pm = &lsdc_pm_ops,
> +};
> +
> +static int __init loongson_module_init(void)
> +{
> + struct pci_dev *pdev = NULL;
> +
> + if (video_firmware_drivers_only())
> + return -ENODEV;
> +
> + /* Multiple video card workaround */
> + while ((pdev = pci_get_class(PCI_CLASS_DISPLAY_VGA << 8, pdev))) {
> + if (pdev->vendor != PCI_VENDOR_ID_LOONGSON) {
> + pr_info("Discrete graphic card detected, abort\n");
> + return 0;
> + }
> + }
> +
> + return pci_register_driver(&lsdc_pci_driver);
> +}
> +module_init(loongson_module_init);
> +
> +static void __exit loongson_module_exit(void)
> +{
> + pci_unregister_driver(&lsdc_pci_driver);
> +}
> +module_exit(loongson_module_exit);
> +
> +MODULE_DEVICE_TABLE(pci, lsdc_pciid_list);
> +MODULE_AUTHOR(DRIVER_AUTHOR);
> +MODULE_DESCRIPTION(DRIVER_DESC);
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/gpu/drm/loongson/lsdc_drv.h b/drivers/gpu/drm/loongson/lsdc_drv.h
> new file mode 100644
> index 000000000000..f3a1b6a347c8
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_drv.h
> @@ -0,0 +1,485 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#ifndef __LSDC_DRV_H__
> +#define __LSDC_DRV_H__
> +
> +#include <linux/pci.h>
> +
> +#include <drm/drm_connector.h>
> +#include <drm/drm_crtc.h>
> +#include <drm/drm_device.h>
> +#include <drm/drm_encoder.h>
> +#include <drm/drm_file.h>
> +#include <drm/drm_plane.h>
> +#include <drm/ttm/ttm_device.h>
> +
> +#include "lsdc_i2c.h"
> +#include "lsdc_irq.h"
> +#include "lsdc_gfxpll.h"
> +#include "lsdc_pixpll.h"
> +#include "lsdc_regs.h"
> +#include "lsdc_output.h"
> +
> +/* Currently, all loongson display controller has two display pipes */
> +#define LSDC_NUM_CRTC 2
> +
> +/*
> + * LS7A1000 and LS7A2000 function as south & north bridge chipset of the
> + * LS3A4000/LS3A5000/LS3A6000, They are typically equipped with on-board
> + * video RAM. While LS2K2000/LS2K1000/LS2K0500 are just low cost SoCs which
>From lower to greater may be better, e.g. LS2K0500/LS2K1000/LS2K2000.
And introduce LS7A1000 before LS7A2000 (see below).
> + * sharing the system RAM as video ram. They don't have dediacated VRAM.
> + *
> + * LS7A2000 integrated a 32-bit DDR4@...0 video memtory controller, while
> + * it is just 16-bit DDR3 for LS7A1000. LS7A2000 integrate Loongson self
> + * maded LoongGPU, LS7A1000 integrate GC1000 due to historical reasons.
> + *
> + * The display controller in LS7A2000 has two display pipe, yet it has
> + * integrate three encoders, display pipe 0 is attached with a transparent
> + * VGA encoder and a HDMI encoder, they are parallel. Display pipe 1 has
> + * only one HDMI phy connected.
> + *
> + * ______________________ _____________
> + * | +-----+ | | |
> + * | CRTC0 -+--> | VGA | ----> VGA Connector ---> | VGA Monitor |<---+
> + * | | +-----+ | |_____________| |
> + * | | | ______________ |
> + * | | +------+ | | | |
> + * | +--> | HDMI | ----> HDMI Connector --> | HDMI Monitor |<--+
> + * | +------+ | |______________| |
> + * | +------+ | |
> + * | | i2c6 | <-------------------------------------------+
> + * | +------+ |
> + * | |
> + * | DC in LS7A2000 |
> + * | |
> + * | +------+ |
> + * | | i2c7 | <--------------------------------+
> + * | +------+ | |
> + * | | ______|_______
> + * | +------+ | | |
> + * | CRTC1 ---> | HDMI | ----> HDMI Connector ---> | HDMI Monitor |
> + * | +------+ | |______________|
> + * |______________________|
> + *
> + *
> + * The display controller in LS7A1000 has only two-way DVO interface exported,
> + * thus, external encoder(TX chip) is required except connected with DPI panel
> + * directly.
> + * ___________________ _________
> + * | -------| | |
> + * | CRTC0 --> | DVO0 ----> Encoder0 ---> Connector0 ---> | Display |
> + * | _ _ -------| ^ ^ |_________|
> + * | | | | | +------+ | | |
> + * | |_| |_| | i2c6 | <--------+-------------+
> + * | +------+ |
> + * | |
> + * | DC in LS7A1000 |
> + * | |
> + * | _ _ +------+ |
> + * | | | | | | i2c7 | <--------+-------------+
> + * | |_| |_| +------+ | | | _________
> + * | -------| | | | |
> + * | CRTC1 --> | DVO1 ----> Encoder1 ---> Connector1 ---> | Panel |
> + * | -------| |_________|
> + * |___________________|
> + *
> + * There is only a 1:1 mapping of crtcs, encoders and connectors for the DC,
> + * display pipe 0 = crtc0 + dvo0 + encoder0 + connector0 + cursor0 + primary0
> + * display pipe 1 = crtc1 + dvo1 + encoder1 + connectro1 + cursor1 + primary1
> + * Each CRTC has two FB address registers.
> + *
> + * The DC in LS7A1000/LS2K1000 has the pci vendor/device ID: 0x0014:0x7a06,
> + * The DC in LS7A2000/LS2K2000 has the pci vendor/device ID: 0x0014:0x7a36.
> + *
> + * The GPU in LS7A1000 has the pci vendor/device ID: 0x0014:0x7a15,
> + * The GPU in LS7A2000 has the pci vendor/device ID: 0x0014:0x7a25.
> + *
> + * LS7A1000/LS7A2000 can only be used with LS3A4000, LS3A5000 and LS3A6000
> + * desktop or server class CPUs, thus CPU PRID can be used to distinguish
> + * those SoC and the desktop level CPU on the runtime.
> + */
> +enum loongson_chip_id {
> + CHIP_LS7A1000 = 0,
> + CHIP_LS7A2000 = 1,
> + CHIP_LS_LAST,
> +};
> +
> +const struct lsdc_desc *
> +lsdc_device_probe(struct pci_dev *pdev, enum loongson_chip_id chip);
> +
> +struct lsdc_kms_funcs;
> +
> +/* DC specific */
> +
> +struct lsdc_desc {
> + u32 num_of_crtc;
> + u32 max_pixel_clk;
> + u32 max_width;
> + u32 max_height;
> + u32 num_of_hw_cursor;
> + u32 hw_cursor_w;
> + u32 hw_cursor_h;
> + u32 pitch_align; /* CRTC DMA alignment constraint */
> + u64 mc_bits; /* physical address bus bit width */
> + bool has_vblank_counter; /* 32 bit hw vsync counter */
> +
> + /* device dependent ops, dc side */
> + const struct lsdc_kms_funcs *funcs;
> +};
> +
> +/* GFX related resources wrangler */
> +
> +struct loongson_gfx_desc {
> + struct lsdc_desc dc;
> +
> + u32 conf_reg_base;
> +
> + /* raw auxiliary resource */
> +
> + /* GFXPLL shared by the DC, GMC and GPU */
> + struct {
> + u32 reg_offset;
> + u32 reg_size;
> + } gfxpll;
> +
> + struct {
> + u32 reg_offset;
> + u32 reg_size;
> + } pixpll[LSDC_NUM_CRTC];
> +
> + enum loongson_chip_id chip_id;
> + char model[64];
> +};
> +
> +static inline const struct loongson_gfx_desc *
> +to_loongson_gfx(const struct lsdc_desc *dcp)
> +{
> + return container_of_const(dcp, struct loongson_gfx_desc, dc);
> +};
> +
> +struct lsdc_reg32 {
> + char *name;
> + u32 offset;
> +};
> +
> +/* crtc hardware related ops */
> +
> +struct lsdc_crtc;
> +
> +struct lsdc_crtc_hw_ops {
> + void (*enable)(struct lsdc_crtc *lcrtc);
> + void (*disable)(struct lsdc_crtc *lcrtc);
> + void (*enable_vblank)(struct lsdc_crtc *lcrtc);
> + void (*disable_vblank)(struct lsdc_crtc *lcrtc);
> + void (*flip)(struct lsdc_crtc *lcrtc);
> + void (*clone)(struct lsdc_crtc *lcrtc);
> + void (*get_scan_pos)(struct lsdc_crtc *lcrtc, int *hpos, int *vpos);
> + void (*set_mode)(struct lsdc_crtc *lcrtc, const struct drm_display_mode *mode);
> + void (*soft_reset)(struct lsdc_crtc *lcrtc);
> + void (*reset)(struct lsdc_crtc *lcrtc);
> +
> + u32 (*get_vblank_counter)(struct lsdc_crtc *lcrtc);
> + void (*set_dma_step)(struct lsdc_crtc *lcrtc, enum lsdc_dma_steps step);
> +};
> +
> +struct lsdc_crtc {
> + struct drm_crtc base;
> + struct lsdc_pixpll pixpll;
> + struct lsdc_device *ldev;
> + const struct lsdc_crtc_hw_ops *hw_ops;
> + const struct lsdc_reg32 *preg;
> + unsigned int nreg;
> + struct drm_info_list *p_info_list;
> + int n_info_list;
> +};
> +
> +/* primary plane hardware related ops */
> +
> +struct lsdc_primary;
> +
> +struct lsdc_primary_plane_ops {
> + void (*update_fb_addr)(struct lsdc_primary *plane, u64 addr);
> + void (*update_fb_stride)(struct lsdc_primary *plane, u32 stride);
> + void (*update_fb_format)(struct lsdc_primary *plane,
> + const struct drm_format_info *format);
> +};
> +
> +struct lsdc_primary {
> + struct drm_plane base;
> + const struct lsdc_primary_plane_ops *ops;
> + struct lsdc_device *ldev;
> +};
> +
> +/* cursor plane hardware related ops */
> +
> +struct lsdc_cursor;
> +
> +struct lsdc_cursor_plane_ops {
> + void (*update_bo_addr)(struct lsdc_cursor *plane, u64 addr);
> + void (*update_cfg)(struct lsdc_cursor *plane,
> + enum lsdc_cursor_size cursor_size,
> + enum lsdc_cursor_format);
> + void (*update_position)(struct lsdc_cursor *plane, int x, int y);
> +};
> +
> +struct lsdc_cursor {
> + struct drm_plane base;
> + const struct lsdc_cursor_plane_ops *ops;
> + struct lsdc_device *ldev;
> +};
> +
> +struct lsdc_display_pipe {
> + struct lsdc_crtc crtc;
> + struct lsdc_primary primary;
> + struct lsdc_cursor cursor;
> + struct drm_encoder encoder;
> + struct drm_connector connector;
> + struct lsdc_i2c *li2c;
> + unsigned int index;
> +};
> +
> +struct lsdc_kms_funcs {
> + irqreturn_t (*irq_handler)(int irq, void *arg);
> +
> + int (*create_i2c)(struct drm_device *ddev,
> + struct lsdc_display_pipe *dispipe,
> + unsigned int index);
> +
> + int (*output_init)(struct drm_device *ddev,
> + struct lsdc_display_pipe *dispipe,
> + struct i2c_adapter *ddc,
> + unsigned int index);
> +
> + int (*cursor_plane_init)(struct drm_device *ddev,
> + struct drm_plane *plane,
> + unsigned int index);
> +
> + int (*primary_plane_init)(struct drm_device *ddev,
> + struct drm_plane *plane,
> + unsigned int index);
> +
> + int (*crtc_init)(struct drm_device *ddev,
> + struct drm_crtc *crtc,
> + struct drm_plane *primary,
> + struct drm_plane *cursor,
> + unsigned int index);
> +};
> +
> +static inline struct lsdc_crtc *
> +to_lsdc_crtc(struct drm_crtc *crtc)
> +{
> + return container_of(crtc, struct lsdc_crtc, base);
> +}
> +
> +static inline struct lsdc_primary *
> +to_lsdc_primary(struct drm_plane *plane)
> +{
> + return container_of(plane, struct lsdc_primary, base);
> +}
> +
> +static inline struct lsdc_cursor *
> +to_lsdc_cursor(struct drm_plane *plane)
> +{
> + return container_of(plane, struct lsdc_cursor, base);
> +}
> +
> +static inline struct lsdc_display_pipe *
> +crtc_to_display_pipe(struct drm_crtc *crtc)
> +{
> + return container_of(crtc, struct lsdc_display_pipe, crtc.base);
> +}
> +
> +static inline struct lsdc_display_pipe *
> +primary_to_display_pipe(struct drm_plane *plane)
> +{
> + return container_of(plane, struct lsdc_display_pipe, primary.base);
> +}
> +
> +static inline struct lsdc_display_pipe *
> +cursor_to_display_pipe(struct drm_plane *plane)
> +{
> + return container_of(plane, struct lsdc_display_pipe, cursor.base);
> +}
> +
> +static inline struct lsdc_display_pipe *
> +connector_to_display_pipe(struct drm_connector *connector)
> +{
> + return container_of(connector, struct lsdc_display_pipe, connector);
> +}
> +
> +static inline struct lsdc_display_pipe *
> +encoder_to_display_pipe(struct drm_encoder *encoder)
> +{
> + return container_of(encoder, struct lsdc_display_pipe, encoder);
> +}
> +
> +struct lsdc_crtc_state {
> + struct drm_crtc_state base;
> + struct lsdc_pixpll_parms pparms;
> +};
> +
> +struct lsdc_gem {
> + /* @mutex: protect objects list */
> + struct mutex mutex;
> + struct list_head objects;
> +};
> +
> +struct lsdc_device {
> + struct drm_device base;
> + struct ttm_device bdev;
> +
> + /* @descp: features description of the DC variant */
> + const struct lsdc_desc *descp;
> + struct pci_dev *dc;
> + struct pci_dev *gpu;
> +
> + struct loongson_gfxpll *gfxpll;
> +
> + /* @reglock: protects concurrent access */
> + spinlock_t reglock;
> +
> + void __iomem *reg_base;
> + resource_size_t vram_base;
> + resource_size_t vram_size;
> +
> + resource_size_t gtt_base;
> + resource_size_t gtt_size;
> +
> + struct lsdc_display_pipe dispipe[LSDC_NUM_CRTC];
> +
> + struct lsdc_gem gem;
> +
> + u32 irq_status;
> +
> + /* tracking pinned memory */
> + size_t vram_pinned_size;
> + size_t gtt_pinned_size;
> +
> + /* @num_output: count the number of active display pipe */
> + unsigned int num_output;
> +};
> +
> +static inline struct lsdc_device *tdev_to_ldev(struct ttm_device *bdev)
> +{
> + return container_of(bdev, struct lsdc_device, bdev);
> +}
> +
> +static inline struct lsdc_device *to_lsdc(struct drm_device *ddev)
> +{
> + return container_of(ddev, struct lsdc_device, base);
> +}
> +
> +static inline struct lsdc_crtc_state *to_lsdc_crtc_state(struct drm_crtc_state *base)
> +{
> + return container_of(base, struct lsdc_crtc_state, base);
> +}
> +
> +int ls7a1000_crtc_init(struct drm_device *ddev,
> + struct drm_crtc *crtc,
> + struct drm_plane *primary,
> + struct drm_plane *cursor,
> + unsigned int index);
> +
> +int ls7a2000_crtc_init(struct drm_device *ddev,
> + struct drm_crtc *crtc,
> + struct drm_plane *primary,
> + struct drm_plane *cursor,
> + unsigned int index);
> +
> +void lsdc_debugfs_init(struct drm_minor *minor);
> +
> +int lsdc_primary_plane_init(struct drm_device *ddev,
> + struct drm_plane *plane,
> + unsigned int index);
> +
> +int ls7a1000_cursor_plane_init(struct drm_device *ddev,
> + struct drm_plane *plane,
> + unsigned int index);
> +
> +int ls7a2000_cursor_plane_init(struct drm_device *ddev,
> + struct drm_plane *plane,
> + unsigned int index);
> +
> +/* registers access helpers */
> +
> +static inline u32 lsdc_rreg32(struct lsdc_device *ldev, u32 offset)
> +{
> + return readl(ldev->reg_base + offset);
> +}
> +
> +static inline void lsdc_wreg32(struct lsdc_device *ldev, u32 offset, u32 val)
> +{
> + writel(val, ldev->reg_base + offset);
> +}
> +
> +static inline void lsdc_ureg32_set(struct lsdc_device *ldev,
> + u32 offset,
> + u32 mask)
> +{
> + void __iomem *addr = ldev->reg_base + offset;
> + u32 val = readl(addr);
> +
> + writel(val | mask, addr);
> +}
> +
> +static inline void lsdc_ureg32_clr(struct lsdc_device *ldev,
> + u32 offset,
> + u32 mask)
> +{
> + void __iomem *addr = ldev->reg_base + offset;
> + u32 val = readl(addr);
> +
> + writel(val & ~mask, addr);
> +}
> +
> +static inline u32 lsdc_pipe_rreg32(struct lsdc_device *ldev,
> + u32 offset,
> + u32 pipe)
> +{
> + return readl(ldev->reg_base + offset + pipe * CRTC_PIPE_OFFSET);
> +}
> +
> +#define lsdc_hdmi_rreg32 lsdc_pipe_rreg32
> +#define lsdc_crtc_rreg32 lsdc_pipe_rreg32
> +
> +static inline void lsdc_pipe_wreg32(struct lsdc_device *ldev,
> + u32 offset,
> + u32 pipe,
> + u32 val)
> +{
> + writel(val, ldev->reg_base + offset + pipe * CRTC_PIPE_OFFSET);
> +}
> +
> +#define lsdc_hdmi_wreg32 lsdc_pipe_wreg32
> +#define lsdc_crtc_wreg32 lsdc_pipe_wreg32
> +
> +static inline void lsdc_crtc_ureg32_set(struct lsdc_device *ldev,
> + u32 offset,
> + u32 pipe,
> + u32 bit)
> +{
> + void __iomem *addr;
> + u32 val;
> +
> + addr = ldev->reg_base + offset + pipe * CRTC_PIPE_OFFSET;
> + val = readl(addr);
> + writel(val | bit, addr);
> +}
> +
> +static inline void lsdc_crtc_ureg32_clr(struct lsdc_device *ldev,
> + u32 offset,
> + u32 pipe,
> + u32 bit)
> +{
> + void __iomem *addr;
> + u32 val;
> +
> + addr = ldev->reg_base + offset + pipe * CRTC_PIPE_OFFSET;
> + val = readl(addr);
> + writel(val & ~bit, addr);
> +}
> +
> +#endif
> diff --git a/drivers/gpu/drm/loongson/lsdc_gem.c b/drivers/gpu/drm/loongson/lsdc_gem.c
> new file mode 100644
> index 000000000000..37b7577dfc46
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_gem.c
> @@ -0,0 +1,319 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#include <linux/dma-buf.h>
> +
> +#include <drm/drm_debugfs.h>
> +#include <drm/drm_file.h>
> +#include <drm/drm_gem.h>
> +#include <drm/drm_prime.h>
> +
> +#include "lsdc_drv.h"
> +#include "lsdc_gem.h"
> +#include "lsdc_ttm.h"
> +
> +static int lsdc_gem_prime_pin(struct drm_gem_object *obj)
> +{
> + struct lsdc_bo *lbo = gem_to_lsdc_bo(obj);
> + int ret;
> +
> + ret = lsdc_bo_reserve(lbo);
> + if (unlikely(ret))
> + return ret;
> +
> + ret = lsdc_bo_pin(lbo, LSDC_GEM_DOMAIN_GTT, NULL);
> + if (likely(ret == 0))
> + lbo->sharing_count++;
> +
> + lsdc_bo_unreserve(lbo);
> +
> + return ret;
> +}
> +
> +static void lsdc_gem_prime_unpin(struct drm_gem_object *obj)
> +{
> + struct lsdc_bo *lbo = gem_to_lsdc_bo(obj);
> + int ret;
> +
> + ret = lsdc_bo_reserve(lbo);
> + if (unlikely(ret))
> + return;
> +
> + lsdc_bo_unpin(lbo);
> + if (lbo->sharing_count)
> + lbo->sharing_count--;
> +
> + lsdc_bo_unreserve(lbo);
> +}
> +
> +static struct sg_table *lsdc_gem_prime_get_sg_table(struct drm_gem_object *obj)
> +{
> + struct ttm_buffer_object *tbo = to_ttm_bo(obj);
> + struct ttm_tt *tt = tbo->ttm;
> +
> + if (!tt) {
> + drm_err(obj->dev, "sharing a buffer without backing memory\n");
> + return ERR_PTR(-ENOMEM);
> + }
> +
> + return drm_prime_pages_to_sg(obj->dev, tt->pages, tt->num_pages);
> +}
> +
> +static void lsdc_gem_object_free(struct drm_gem_object *obj)
> +{
> + struct ttm_buffer_object *tbo = to_ttm_bo(obj);
> +
> + if (tbo)
> + ttm_bo_put(tbo);
> +}
> +
> +static int lsdc_gem_object_vmap(struct drm_gem_object *obj,
> + struct iosys_map *map)
> +{
> + struct ttm_buffer_object *tbo = to_ttm_bo(obj);
> + struct lsdc_bo *lbo = to_lsdc_bo(tbo);
> + int ret;
> +
> + if (lbo->vmap_count > 0) {
> + ++lbo->vmap_count;
> + goto out;
> + }
> +
> + ret = lsdc_bo_pin(lbo, 0, NULL);
> + if (unlikely(ret)) {
> + drm_err(obj->dev, "pin %p for vmap failed\n", lbo);
> + return ret;
> + }
> +
> + ret = ttm_bo_vmap(tbo, &lbo->map);
> + if (ret) {
> + drm_err(obj->dev, "ttm bo vmap failed\n");
> + lsdc_bo_unpin(lbo);
> + return ret;
> + }
> +
> + lbo->vmap_count = 1;
> +
> +out:
> + *map = lbo->map;
> +
> + return 0;
> +}
> +
> +static void lsdc_gem_object_vunmap(struct drm_gem_object *obj,
> + struct iosys_map *map)
> +{
> + struct ttm_buffer_object *tbo = to_ttm_bo(obj);
> + struct lsdc_bo *lbo = to_lsdc_bo(tbo);
> +
> + if (unlikely(!lbo->vmap_count)) {
> + drm_warn(obj->dev, "%p is not mapped\n", lbo);
> + return;
> + }
> +
> + --lbo->vmap_count;
> + if (lbo->vmap_count == 0) {
> + ttm_bo_vunmap(tbo, &lbo->map);
> +
> + lsdc_bo_unpin(lbo);
> + }
> +}
> +
> +static int lsdc_gem_object_mmap(struct drm_gem_object *obj,
> + struct vm_area_struct *vma)
> +{
> + struct ttm_buffer_object *tbo = to_ttm_bo(obj);
> + int ret;
> +
> + ret = ttm_bo_mmap_obj(vma, tbo);
> + if (unlikely(ret)) {
> + drm_warn(obj->dev, "mmap %p failed\n", tbo);
> + return ret;
> + }
> +
> + drm_gem_object_put(obj);
> +
> + return 0;
> +}
> +
> +static const struct drm_gem_object_funcs lsdc_gem_object_funcs = {
> + .free = lsdc_gem_object_free,
> + .export = drm_gem_prime_export,
> + .pin = lsdc_gem_prime_pin,
> + .unpin = lsdc_gem_prime_unpin,
> + .get_sg_table = lsdc_gem_prime_get_sg_table,
> + .vmap = lsdc_gem_object_vmap,
> + .vunmap = lsdc_gem_object_vunmap,
> + .mmap = lsdc_gem_object_mmap,
> +};
> +
> +struct drm_gem_object *
> +lsdc_gem_object_create(struct drm_device *ddev,
> + u32 domain,
> + size_t size,
> + bool kerenl,
> + struct sg_table *sg,
> + struct dma_resv *resv)
> +{
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + struct drm_gem_object *gobj;
> + struct lsdc_bo *lbo;
> + int ret;
> +
> + lbo = lsdc_bo_create(ddev, domain, size, kerenl, sg, resv);
> + if (IS_ERR(lbo)) {
> + ret = PTR_ERR(lbo);
> + return ERR_PTR(ret);
> + }
> +
> + gobj = &lbo->tbo.base;
> + gobj->funcs = &lsdc_gem_object_funcs;
> +
> + /* tracking the BOs we created */
> + mutex_lock(&ldev->gem.mutex);
> + list_add_tail(&lbo->list, &ldev->gem.objects);
> + mutex_unlock(&ldev->gem.mutex);
> +
> + return gobj;
> +}
> +
> +struct drm_gem_object *
> +lsdc_prime_import_sg_table(struct drm_device *ddev,
> + struct dma_buf_attachment *attach,
> + struct sg_table *sg)
> +{
> + struct dma_resv *resv = attach->dmabuf->resv;
> + u64 size = attach->dmabuf->size;
> + struct drm_gem_object *gobj;
> + struct lsdc_bo *lbo;
> +
> + dma_resv_lock(resv, NULL);
> + gobj = lsdc_gem_object_create(ddev, LSDC_GEM_DOMAIN_GTT, size,
> + false, sg, resv);
> + dma_resv_unlock(resv);
> +
> + if (IS_ERR(gobj)) {
> + drm_err(ddev, "Failed to import sg table\n");
> + return gobj;
> + }
> +
> + lbo = gem_to_lsdc_bo(gobj);
> + lbo->sharing_count = 1;
> +
> + return gobj;
> +}
> +
> +int lsdc_dumb_create(struct drm_file *file,
> + struct drm_device *ddev,
> + struct drm_mode_create_dumb *args)
> +{
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + const struct lsdc_desc *descp = ldev->descp;
> + u32 domain = LSDC_GEM_DOMAIN_VRAM;
> + struct drm_gem_object *gobj;
> + size_t size;
> + u32 pitch;
> + u32 handle;
> + int ret;
> +
> + if (!args->width || !args->height)
> + return -EINVAL;
> +
> + /* Loongson diaplay controller only support 32-bit and 16-bit FB */
> + if (args->bpp != 32 && args->bpp != 16)
> + return -EINVAL;
> +
> + pitch = args->width * args->bpp / 8;
> + pitch = ALIGN(pitch, descp->pitch_align);
> + size = pitch * args->height;
> + size = ALIGN(size, PAGE_SIZE);
> +
> + /* Maximum bo size allowed is the half vram size available */
> + if (size > ldev->vram_size) {
> + drm_err(ddev, "Requesting(%zuMB) more than owned(%uMB)\n",
> + size >> 20, (u32)(ldev->vram_size >> 20));
> + return -ENOMEM;
> + }
> +
> + gobj = lsdc_gem_object_create(ddev,
> + domain,
> + size,
> + false,
> + NULL,
> + NULL);
> + if (IS_ERR(gobj)) {
> + drm_err(ddev, "Failed to create gem object\n");
> + return PTR_ERR(gobj);
> + }
> +
> + ret = drm_gem_handle_create(file, gobj, &handle);
> +
> + /* drop reference from allocate, handle holds it now */
> + drm_gem_object_put(gobj);
> + if (ret)
> + return ret;
> +
> + args->pitch = pitch;
> + args->size = size;
> + args->handle = handle;
> +
> + return 0;
> +}
> +
> +int lsdc_dumb_map_offset(struct drm_file *filp,
> + struct drm_device *ddev,
> + u32 handle,
> + uint64_t *offset)
> +{
> + struct drm_gem_object *gobj;
> +
> + gobj = drm_gem_object_lookup(filp, handle);
> + if (!gobj)
> + return -ENOENT;
> +
> + *offset = drm_vma_node_offset_addr(&gobj->vma_node);
> +
> + drm_gem_object_put(gobj);
> +
> + return 0;
> +}
> +
> +void lsdc_gem_init(struct drm_device *ddev)
> +{
> + struct lsdc_device *ldev = to_lsdc(ddev);
> +
> + mutex_init(&ldev->gem.mutex);
> + INIT_LIST_HEAD(&ldev->gem.objects);
> +}
> +
> +int lsdc_show_buffer_object(struct seq_file *m, void *arg)
> +{
> + struct drm_info_node *node = (struct drm_info_node *)m->private;
> + struct drm_device *ddev = node->minor->dev;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + struct lsdc_bo *lbo;
> + unsigned int i = 0;
> +
> + mutex_lock(&ldev->gem.mutex);
> +
> + list_for_each_entry(lbo, &ldev->gem.objects, list) {
> + struct ttm_buffer_object *tbo = &lbo->tbo;
> + struct ttm_resource *resource = tbo->resource;
> +
> + seq_printf(m, "bo[%04u][%p]: size: %8zu KB %s offset: %8llx\n",
> + i, lbo,
> + lsdc_bo_size(lbo) >> 10,
> + lsdc_mem_type_to_str(resource->mem_type),
> + lsdc_bo_gpu_offset(lbo));
> + i++;
> + }
> +
> + mutex_unlock(&ldev->gem.mutex);
> +
> + seq_printf(m, "Pinned BO size: VRAM: %zu KB, GTT: %zu KB\n",
> + ldev->vram_pinned_size >> 10, ldev->gtt_pinned_size >> 10);
> +
> + return 0;
> +}
> diff --git a/drivers/gpu/drm/loongson/lsdc_gem.h b/drivers/gpu/drm/loongson/lsdc_gem.h
> new file mode 100644
> index 000000000000..d6c0d0499e92
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_gem.h
> @@ -0,0 +1,37 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#ifndef __LSDC_GEM_H__
> +#define __LSDC_GEM_H__
> +
> +#include <drm/drm_device.h>
> +#include <drm/drm_gem.h>
> +
> +struct drm_gem_object *
> +lsdc_prime_import_sg_table(struct drm_device *ddev,
> + struct dma_buf_attachment *attach,
> + struct sg_table *sg);
> +
> +int lsdc_dumb_map_offset(struct drm_file *file,
> + struct drm_device *dev,
> + u32 handle,
> + uint64_t *offset);
> +
> +int lsdc_dumb_create(struct drm_file *file,
> + struct drm_device *ddev,
> + struct drm_mode_create_dumb *args);
> +
> +void lsdc_gem_init(struct drm_device *ddev);
> +int lsdc_show_buffer_object(struct seq_file *m, void *arg);
> +
> +struct drm_gem_object *
> +lsdc_gem_object_create(struct drm_device *ddev,
> + u32 domain,
> + size_t size,
> + bool kerenl,
> + struct sg_table *sg,
> + struct dma_resv *resv);
> +
> +#endif
> diff --git a/drivers/gpu/drm/loongson/lsdc_gfxpll.c b/drivers/gpu/drm/loongson/lsdc_gfxpll.c
> new file mode 100644
> index 000000000000..d45a03038841
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_gfxpll.c
> @@ -0,0 +1,199 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#include <linux/delay.h>
> +
> +#include <drm/drm_file.h>
> +#include <drm/drm_managed.h>
> +#include <drm/drm_print.h>
> +
> +#include "lsdc_drv.h"
> +
> +/*
> + * GFX PLL is the PLL used by DC, GMC and GPU, the structure of the GFX PLL
> + * may suffer from change across chip variants.
> + *
> + *
> + * +-------------+ sel_out_dc
> + * +----| / div_out_0 | _____/ _____ DC
> + * | +-------------+
> + * refclk +---------+ +-------+ | +-------------+ sel_out_gmc
> + * ---+---> | div_ref | ---> | loopc | --+--> | / div_out_1 | _____/ _____ GMC
> + * | +---------+ +-------+ | +-------------+
> + * | / * | +-------------+ sel_out_gpu
> + * | +----| / div_out_2 | _____/ _____ GPU
> + * | +-------------+
> + * | ^
> + * | |
> + * +--------------------------- bypass ----------------------+
> + */
> +
> +struct loongson_gfxpll_bitmap {
> + /* Byte 0 ~ Byte 3 */
> + unsigned div_out_dc : 7; /* 6 : 0 DC output clock divider */
> + unsigned div_out_gmc : 7; /* 13 : 7 GMC output clock divider */
> + unsigned div_out_gpu : 7; /* 20 : 14 GPU output clock divider */
> + unsigned loopc : 9; /* 29 : 21 clock multiplier */
> + unsigned _reserved_1_ : 2; /* 31 : 30 */
> +
> + /* Byte 4 ~ Byte 7 */
> + unsigned div_ref : 7; /* 38 : 32 Input clock divider */
> + unsigned locked : 1; /* 39 PLL locked indicator */
> + unsigned sel_out_dc : 1; /* 40 dc output clk enable */
> + unsigned sel_out_gmc : 1; /* 41 gmc output clk enable */
> + unsigned sel_out_gpu : 1; /* 42 gpu output clk enable */
> + unsigned set_param : 1; /* 43 Trigger the update */
> + unsigned bypass : 1; /* 44 */
> + unsigned powerdown : 1; /* 45 */
> + unsigned _reserved_2_ : 18; /* 46 : 63 no use */
> +};
> +
> +union loongson_gfxpll_reg_bitmap {
> + struct loongson_gfxpll_bitmap bitmap;
> + u32 w[2];
> + u64 d;
> +};
> +
> +static void __gfxpll_rreg(struct loongson_gfxpll *this,
> + union loongson_gfxpll_reg_bitmap *reg)
> +{
> +#if defined(CONFIG_64BIT)
> + reg->d = readq(this->mmio);
> +#else
> + reg->w[0] = readl(this->mmio);
> + reg->w[1] = readl(this->mmio + 4);
> +#endif
> +}
> +
> +/* Update new parameters to the hardware */
> +
> +static int loongson_gfxpll_update(struct loongson_gfxpll * const this,
> + struct loongson_gfxpll_parms const *pin)
> +{
> + /* None, TODO */
> +
> + return 0;
> +}
> +
> +static void loongson_gfxpll_get_rates(struct loongson_gfxpll * const this,
> + unsigned int *dc,
> + unsigned int *gmc,
> + unsigned int *gpu)
> +{
> + struct loongson_gfxpll_parms *pparms = &this->parms;
> + union loongson_gfxpll_reg_bitmap gfxpll_reg;
> + unsigned int pre_output;
> + unsigned int dc_mhz;
> + unsigned int gmc_mhz;
> + unsigned int gpu_mhz;
> +
> + __gfxpll_rreg(this, &gfxpll_reg);
> +
> + pparms->div_ref = gfxpll_reg.bitmap.div_ref;
> + pparms->loopc = gfxpll_reg.bitmap.loopc;
> +
> + pparms->div_out_dc = gfxpll_reg.bitmap.div_out_dc;
> + pparms->div_out_gmc = gfxpll_reg.bitmap.div_out_gmc;
> + pparms->div_out_gpu = gfxpll_reg.bitmap.div_out_gpu;
> +
> + pre_output = pparms->ref_clock / pparms->div_ref * pparms->loopc;
> +
> + dc_mhz = pre_output / pparms->div_out_dc / 1000;
> + gmc_mhz = pre_output / pparms->div_out_gmc / 1000;
> + gpu_mhz = pre_output / pparms->div_out_gpu / 1000;
> +
> + if (dc)
> + *dc = dc_mhz;
> +
> + if (gmc)
> + *gmc = gmc_mhz;
> +
> + if (gpu)
> + *gpu = gpu_mhz;
> +}
> +
> +static void loongson_gfxpll_print(struct loongson_gfxpll * const this,
> + struct drm_printer *p,
> + bool verbose)
> +{
> + struct loongson_gfxpll_parms *parms = &this->parms;
> + unsigned int dc, gmc, gpu;
> +
> + if (verbose) {
> + drm_printf(p, "reference clock: %u\n", parms->ref_clock);
> + drm_printf(p, "div_ref = %u\n", parms->div_ref);
> + drm_printf(p, "loopc = %u\n", parms->loopc);
> +
> + drm_printf(p, "div_out_dc = %u\n", parms->div_out_dc);
> + drm_printf(p, "div_out_gmc = %u\n", parms->div_out_gmc);
> + drm_printf(p, "div_out_gpu = %u\n", parms->div_out_gpu);
> + }
> +
> + this->funcs->get_rates(this, &dc, &gmc, &gpu);
> +
> + drm_printf(p, "dc: %uMHz, gmc: %uMHz, gpu: %uMHz\n", dc, gmc, gpu);
> +}
> +
> +/* GFX (DC, GPU, GMC) PLL initialization and destroy function */
> +
> +static void loongson_gfxpll_fini(struct drm_device *ddev, void *data)
> +{
> + struct loongson_gfxpll *this = (struct loongson_gfxpll *)data;
> +
> + iounmap(this->mmio);
> +
> + kfree(this);
> +}
> +
> +static int loongson_gfxpll_init(struct loongson_gfxpll * const this)
> +{
> + struct loongson_gfxpll_parms *pparms = &this->parms;
> + struct drm_printer printer = drm_debug_printer("gfxpll:");
> +
> + pparms->ref_clock = LSDC_PLL_REF_CLK;
> +
> + this->mmio = ioremap(this->reg_base, this->reg_size);
> + if (IS_ERR_OR_NULL(this->mmio))
> + return -ENOMEM;
> +
> + this->funcs->print(this, &printer, false);
> +
> + return 0;
> +}
> +
> +static const struct loongson_gfxpll_funcs lsdc_gmc_gpu_funcs = {
> + .init = loongson_gfxpll_init,
> + .update = loongson_gfxpll_update,
> + .get_rates = loongson_gfxpll_get_rates,
> + .print = loongson_gfxpll_print,
> +};
> +
> +int loongson_gfxpll_create(struct drm_device *ddev,
> + struct loongson_gfxpll **ppout)
> +{
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + const struct loongson_gfx_desc *gfx = to_loongson_gfx(ldev->descp);
> + struct loongson_gfxpll *this;
> + int ret;
> +
> + this = kzalloc(sizeof(*this), GFP_KERNEL);
> + if (IS_ERR_OR_NULL(this))
> + return -ENOMEM;
> +
> + this->ddev = ddev;
> + this->reg_size = gfx->gfxpll.reg_size;
> + this->reg_base = gfx->conf_reg_base + gfx->gfxpll.reg_offset;
> + this->funcs = &lsdc_gmc_gpu_funcs;
> +
> + ret = this->funcs->init(this);
> + if (unlikely(ret)) {
> + kfree(this);
> + return ret;
> + }
> +
> + *ppout = this;
> +
> + return drmm_add_action_or_reset(ddev, loongson_gfxpll_fini, this);
> +}
> diff --git a/drivers/gpu/drm/loongson/lsdc_gfxpll.h b/drivers/gpu/drm/loongson/lsdc_gfxpll.h
> new file mode 100644
> index 000000000000..b4749c2d0ef9
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_gfxpll.h
> @@ -0,0 +1,52 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#ifndef __LSDC_GFXPLL_H__
> +#define __LSDC_GFXPLL_H__
> +
> +#include <drm/drm_device.h>
> +
> +struct loongson_gfxpll;
> +
> +struct loongson_gfxpll_parms {
> + unsigned int ref_clock;
> + unsigned int div_ref;
> + unsigned int loopc;
> + unsigned int div_out_dc;
> + unsigned int div_out_gmc;
> + unsigned int div_out_gpu;
> +};
> +
> +struct loongson_gfxpll_funcs {
> + int (*init)(struct loongson_gfxpll * const this);
> +
> + int (*update)(struct loongson_gfxpll * const this,
> + struct loongson_gfxpll_parms const *pin);
> +
> + void (*get_rates)(struct loongson_gfxpll * const this,
> + unsigned int *dc, unsigned int *gmc, unsigned int *gpu);
> +
> + void (*print)(struct loongson_gfxpll * const this,
> + struct drm_printer *printer, bool verbose);
> +};
> +
> +struct loongson_gfxpll {
> + struct drm_device *ddev;
> + void __iomem *mmio;
> +
> + /* PLL register offset */
> + u32 reg_base;
> + /* PLL register size in bytes */
> + u32 reg_size;
> +
> + const struct loongson_gfxpll_funcs *funcs;
> +
> + struct loongson_gfxpll_parms parms;
> +};
> +
> +int loongson_gfxpll_create(struct drm_device *ddev,
> + struct loongson_gfxpll **ppout);
> +
> +#endif
> diff --git a/drivers/gpu/drm/loongson/lsdc_i2c.c b/drivers/gpu/drm/loongson/lsdc_i2c.c
> new file mode 100644
> index 000000000000..e8d07b30a508
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_i2c.c
> @@ -0,0 +1,179 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#include <drm/drm_managed.h>
> +
> +#include "lsdc_drv.h"
> +#include "lsdc_output.h"
> +
> +/*
> + * __lsdc_gpio_i2c_set - set the state of a gpio pin indicated by mask
> + * @mask: gpio pin mask
> + * @state: "0" for low, "1" for high
> + */
> +static void __lsdc_gpio_i2c_set(struct lsdc_i2c * const li2c, int mask, int state)
> +{
> + struct lsdc_device *ldev = to_lsdc(li2c->ddev);
> + unsigned long flags;
> + u8 val;
> +
> + spin_lock_irqsave(&ldev->reglock, flags);
> +
> + if (state) {
> + /*
> + * Setting this pin as input directly, write 1 for input.
> + * The external pull-up resistor will pull the level up
> + */
> + val = readb(li2c->dir_reg);
> + val |= mask;
> + writeb(val, li2c->dir_reg);
> + } else {
> + /* First set this pin as output, write 0 for output */
> + val = readb(li2c->dir_reg);
> + val &= ~mask;
> + writeb(val, li2c->dir_reg);
> +
> + /* Then, make this pin output 0 */
> + val = readb(li2c->dat_reg);
> + val &= ~mask;
> + writeb(val, li2c->dat_reg);
> + }
> +
> + spin_unlock_irqrestore(&ldev->reglock, flags);
> +}
> +
> +/*
> + * __lsdc_gpio_i2c_get - read value back from the gpio pin indicated by mask
> + * @mask: gpio pin mask
> + * return "0" for low, "1" for high
> + */
> +static int __lsdc_gpio_i2c_get(struct lsdc_i2c * const li2c, int mask)
> +{
> + struct lsdc_device *ldev = to_lsdc(li2c->ddev);
> + unsigned long flags;
> + u8 val;
> +
> + spin_lock_irqsave(&ldev->reglock, flags);
> +
> + /* First set this pin as input */
> + val = readb(li2c->dir_reg);
> + val |= mask;
> + writeb(val, li2c->dir_reg);
> +
> + /* Then get level state from this pin */
> + val = readb(li2c->dat_reg);
> +
> + spin_unlock_irqrestore(&ldev->reglock, flags);
> +
> + return (val & mask) ? 1 : 0;
> +}
> +
> +static void lsdc_gpio_i2c_set_sda(void *i2c, int state)
> +{
> + struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c;
> + /* set state on the li2c->sda pin */
> + return __lsdc_gpio_i2c_set(li2c, li2c->sda, state);
> +}
> +
> +static void lsdc_gpio_i2c_set_scl(void *i2c, int state)
> +{
> + struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c;
> + /* set state on the li2c->scl pin */
> + return __lsdc_gpio_i2c_set(li2c, li2c->scl, state);
> +}
> +
> +static int lsdc_gpio_i2c_get_sda(void *i2c)
> +{
> + struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c;
> + /* read value from the li2c->sda pin */
> + return __lsdc_gpio_i2c_get(li2c, li2c->sda);
> +}
> +
> +static int lsdc_gpio_i2c_get_scl(void *i2c)
> +{
> + struct lsdc_i2c * const li2c = (struct lsdc_i2c *)i2c;
> + /* read the value from the li2c->scl pin */
> + return __lsdc_gpio_i2c_get(li2c, li2c->scl);
> +}
> +
> +static void lsdc_destroy_i2c(struct drm_device *ddev, void *data)
> +{
> + struct lsdc_i2c *li2c = (struct lsdc_i2c *)data;
> +
> + if (li2c) {
> + i2c_del_adapter(&li2c->adapter);
> + kfree(li2c);
> + }
> +}
> +
> +/*
> + * The DC in ls7a1000/ls7a2000/ls2k2000 has builtin gpio hardware
> + *
> + * @reg_base: gpio reg base
> + * @index: output channel index, 0 for PIPE0, 1 for PIPE1
> + */
> +int lsdc_create_i2c_chan(struct drm_device *ddev,
> + struct lsdc_display_pipe *dispipe,
> + unsigned int index)
> +{
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + struct i2c_adapter *adapter;
> + struct lsdc_i2c *li2c;
> + int ret;
> +
> + li2c = kzalloc(sizeof(*li2c), GFP_KERNEL);
> + if (!li2c)
> + return -ENOMEM;
> +
> + dispipe->li2c = li2c;
> +
> + if (index == 0) {
> + li2c->sda = 0x01; /* pin 0 */
> + li2c->scl = 0x02; /* pin 1 */
> + } else if (index == 1) {
> + li2c->sda = 0x04; /* pin 2 */
> + li2c->scl = 0x08; /* pin 3 */
> + } else {
> + return -ENOENT;
> + }
> +
> + li2c->ddev = ddev;
> + li2c->dir_reg = ldev->reg_base + LS7A_DC_GPIO_DIR_REG;
> + li2c->dat_reg = ldev->reg_base + LS7A_DC_GPIO_DAT_REG;
> +
> + li2c->bit.setsda = lsdc_gpio_i2c_set_sda;
> + li2c->bit.setscl = lsdc_gpio_i2c_set_scl;
> + li2c->bit.getsda = lsdc_gpio_i2c_get_sda;
> + li2c->bit.getscl = lsdc_gpio_i2c_get_scl;
> + li2c->bit.udelay = 5;
> + li2c->bit.timeout = usecs_to_jiffies(2200);
> + li2c->bit.data = li2c;
> +
> + adapter = &li2c->adapter;
> + adapter->algo_data = &li2c->bit;
> + adapter->owner = THIS_MODULE;
> + adapter->class = I2C_CLASS_DDC;
> + adapter->dev.parent = ddev->dev;
> + adapter->nr = -1;
> +
> + snprintf(adapter->name, sizeof(adapter->name), "lsdc-i2c%u", dispipe->index);
> +
> + i2c_set_adapdata(adapter, li2c);
> +
> + ret = i2c_bit_add_bus(adapter);
> + if (ret) {
> + kfree(li2c);
> + return ret;
> + }
> +
> + ret = drmm_add_action_or_reset(ddev, lsdc_destroy_i2c, li2c);
> + if (ret)
> + return ret;
> +
> + drm_info(ddev, "%s(sda pin mask=%u, scl pin mask=%u) created\n",
> + adapter->name, li2c->sda, li2c->scl);
> +
> + return 0;
> +}
> diff --git a/drivers/gpu/drm/loongson/lsdc_i2c.h b/drivers/gpu/drm/loongson/lsdc_i2c.h
> new file mode 100644
> index 000000000000..180b92fab031
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_i2c.h
> @@ -0,0 +1,29 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#ifndef __LSDC_I2C_H__
> +#define __LSDC_I2C_H__
> +
> +#include <linux/i2c.h>
> +#include <linux/i2c-algo-bit.h>
> +
> +struct lsdc_i2c {
> + struct i2c_adapter adapter;
> + struct i2c_algo_bit_data bit;
> + struct drm_device *ddev;
> + void __iomem *dir_reg;
> + void __iomem *dat_reg;
> + /* pin bit mask */
> + u8 sda;
> + u8 scl;
> +};
> +
> +struct lsdc_display_pipe;
> +
> +int lsdc_create_i2c_chan(struct drm_device *ddev,
> + struct lsdc_display_pipe *dispipe,
> + unsigned int index);
> +
> +#endif
> diff --git a/drivers/gpu/drm/loongson/lsdc_irq.c b/drivers/gpu/drm/loongson/lsdc_irq.c
> new file mode 100644
> index 000000000000..3f151beeb7d6
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_irq.c
> @@ -0,0 +1,81 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#include <drm/drm_vblank.h>
> +
> +#include "lsdc_irq.h"
> +
> +/*
> + * For the DC in ls7a2000, clearing interrupt status is achieved by
> + * write "1" to LSDC_INT_REG, For the DC in ls7a1000, clear interrupt
> + * status is achieved by write "0" to LSDC_INT_REG. Two different hardware
> + * engineer of Loongson modify it as their will.
The same, from ls7a1000 to ls7a2000.
> + */
> +
> +irqreturn_t ls7a2000_dc_irq_handler(int irq, void *arg)
> +{
> + struct drm_device *ddev = arg;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + struct drm_crtc *crtc;
> + u32 val;
> +
> + /* Read the interrupt status */
> + val = lsdc_rreg32(ldev, LSDC_INT_REG);
> + if ((val & INT_STATUS_MASK) == 0) {
> + drm_warn(ddev, "no interrupt occurs\n");
> + return IRQ_NONE;
> + }
> +
> + ldev->irq_status = val;
> +
> + /* write "1" to clear the interrupt status */
> + lsdc_wreg32(ldev, LSDC_INT_REG, val);
> +
> + if (ldev->irq_status & INT_CRTC0_VSYNC) {
> + crtc = drm_crtc_from_index(ddev, 0);
> + drm_crtc_handle_vblank(crtc);
> + }
> +
> + if (ldev->irq_status & INT_CRTC1_VSYNC) {
> + crtc = drm_crtc_from_index(ddev, 1);
> + drm_crtc_handle_vblank(crtc);
> + }
> +
> + return IRQ_HANDLED;
> +}
> +
> +/* For the DC in LS7A1000 and LS2K1000 */
> +irqreturn_t ls7a1000_dc_irq_handler(int irq, void *arg)
> +{
> + struct drm_device *ddev = arg;
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + struct drm_crtc *crtc;
> + u32 val;
> +
> + /* Read the interrupt status */
> + val = lsdc_rreg32(ldev, LSDC_INT_REG);
> + if ((val & INT_STATUS_MASK) == 0) {
> + drm_warn(ddev, "no interrupt occurs\n");
> + return IRQ_NONE;
> + }
> +
> + ldev->irq_status = val;
> +
> + /* write "0" to clear the interrupt status */
> + val &= ~(INT_CRTC0_VSYNC | INT_CRTC1_VSYNC);
> + lsdc_wreg32(ldev, LSDC_INT_REG, val);
> +
> + if (ldev->irq_status & INT_CRTC0_VSYNC) {
> + crtc = drm_crtc_from_index(ddev, 0);
> + drm_crtc_handle_vblank(crtc);
> + }
> +
> + if (ldev->irq_status & INT_CRTC1_VSYNC) {
> + crtc = drm_crtc_from_index(ddev, 1);
> + drm_crtc_handle_vblank(crtc);
> + }
> +
> + return IRQ_HANDLED;
> +}
> diff --git a/drivers/gpu/drm/loongson/lsdc_irq.h b/drivers/gpu/drm/loongson/lsdc_irq.h
> new file mode 100644
> index 000000000000..cd1320252d1d
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_irq.h
> @@ -0,0 +1,16 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#ifndef __LSDC_IRQ_H__
> +#define __LSDC_IRQ_H__
> +
> +#include <linux/irqreturn.h>
> +
> +#include "lsdc_drv.h"
> +
> +irqreturn_t ls7a1000_dc_irq_handler(int irq, void *arg);
> +irqreturn_t ls7a2000_dc_irq_handler(int irq, void *arg);
> +
> +#endif
> diff --git a/drivers/gpu/drm/loongson/lsdc_output.h b/drivers/gpu/drm/loongson/lsdc_output.h
> new file mode 100644
> index 000000000000..a862d57957e3
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_output.h
> @@ -0,0 +1,21 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#ifndef __LSDC_OUTPUT_H__
> +#define __LSDC_OUTPUT_H__
> +
> +#include "lsdc_drv.h"
> +
> +int ls7a1000_output_init(struct drm_device *ddev,
> + struct lsdc_display_pipe *dispipe,
> + struct i2c_adapter *ddc,
> + unsigned int index);
> +
> +int ls7a2000_output_init(struct drm_device *ldev,
> + struct lsdc_display_pipe *dispipe,
> + struct i2c_adapter *ddc,
> + unsigned int index);
> +
> +#endif
> diff --git a/drivers/gpu/drm/loongson/lsdc_pixpll.c b/drivers/gpu/drm/loongson/lsdc_pixpll.c
> new file mode 100644
> index 000000000000..61271061d32e
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_pixpll.c
> @@ -0,0 +1,485 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#include <linux/delay.h>
> +
> +#include <drm/drm_managed.h>
> +
> +#include "lsdc_drv.h"
> +
> +/*
> + * The structure of the pixel PLL register is evolved with times,
> + * it can alse be different across different chip.
> + */
> +
> +/* size is u64, note that all loongson's cpu is little endian.
> + * This structure is same for ls7a2000, ls7a1000 and ls2k2000
> + */
> +struct lsdc_pixpll_reg {
> + /* Byte 0 ~ Byte 3 */
> + unsigned div_out : 7; /* 6 : 0 Output clock divider */
> + unsigned _reserved_1_ : 14; /* 20 : 7 */
> + unsigned loopc : 9; /* 29 : 21 Clock multiplier */
> + unsigned _reserved_2_ : 2; /* 31 : 30 */
> +
> + /* Byte 4 ~ Byte 7 */
> + unsigned div_ref : 7; /* 38 : 32 Input clock divider */
> + unsigned locked : 1; /* 39 PLL locked indicator */
> + unsigned sel_out : 1; /* 40 output clk selector */
> + unsigned _reserved_3_ : 2; /* 42 : 41 */
> + unsigned set_param : 1; /* 43 Trigger the update */
> + unsigned bypass : 1; /* 44 */
> + unsigned powerdown : 1; /* 45 */
> + unsigned _reserved_4_ : 18; /* 46 : 63 no use */
> +};
> +
> +union lsdc_pixpll_reg_bitmap {
> + struct lsdc_pixpll_reg ls7a1000;
> + struct lsdc_pixpll_reg ls7a2000;
> + struct lsdc_pixpll_reg ls2k1000;
> + struct lsdc_pixpll_reg bitmap;
> + u32 w[2];
> + u64 d;
> +};
> +
> +struct clk_to_pixpll_parms_lookup_t {
> + /* kHz */
> + unsigned int clock;
> +
> + unsigned short width;
> + unsigned short height;
> + unsigned short vrefresh;
> +
> + /* Stores parameters for programming the Hardware PLLs */
> + unsigned short div_out;
> + unsigned short loopc;
> + unsigned short div_ref;
> +};
> +
> +static const struct clk_to_pixpll_parms_lookup_t pixpll_parms_table[] = {
> + {148500, 1920, 1080, 60, 11, 49, 3}, /* 1920x1080@...z */
> + {141750, 1920, 1080, 60, 11, 78, 5}, /* 1920x1080@...z */
> + /* 1920x1080@...z */
> + {174500, 1920, 1080, 75, 17, 89, 3}, /* 1920x1080@...z */
> + {181250, 2560, 1080, 75, 8, 58, 4}, /* 2560x1080@...z */
> + {297000, 2560, 1080, 30, 8, 95, 4}, /* 3840x2160@...z */
> + {301992, 1920, 1080, 100, 10, 151, 5}, /* 1920x1080@...Hz */
> + {146250, 1680, 1050, 60, 16, 117, 5}, /* 1680x1050@...z */
> + {135000, 1280, 1024, 75, 10, 54, 4}, /* 1280x1024@...z */
> + {119000, 1680, 1050, 60, 20, 119, 5}, /* 1680x1050@...z */
> + {108000, 1600, 900, 60, 15, 81, 5}, /* 1600x900@...z */
> + /* 1280x1024@...z */
> + /* 1280x960@...z */
> + /* 1152x864@...z */
> +
> + {106500, 1440, 900, 60, 19, 81, 4}, /* 1440x900@...z */
> + {88750, 1440, 900, 60, 16, 71, 5}, /* 1440x900@...z */
> + {83500, 1280, 800, 60, 17, 71, 5}, /* 1280x800@...z */
> + {71000, 1280, 800, 60, 20, 71, 5}, /* 1280x800@...z */
> +
> + {74250, 1280, 720, 60, 22, 49, 3}, /* 1280x720@...z */
> + /* 1280x720@...z */
> +
> + {78750, 1024, 768, 75, 16, 63, 5}, /* 1024x768@...z */
> + {75000, 1024, 768, 70, 29, 87, 4}, /* 1024x768@...z */
> + {65000, 1024, 768, 60, 20, 39, 3}, /* 1024x768@...z */
> +
> + {51200, 1024, 600, 60, 25, 64, 5}, /* 1024x600@...z */
> +
> + {57284, 832, 624, 75, 24, 55, 4}, /* 832x624@...z */
> + {49500, 800, 600, 75, 40, 99, 5}, /* 800x600@...z */
> + {50000, 800, 600, 72, 44, 88, 4}, /* 800x600@...z */
> + {40000, 800, 600, 60, 30, 36, 3}, /* 800x600@...z */
> + {36000, 800, 600, 56, 50, 72, 4}, /* 800x600@...z */
> + {31500, 640, 480, 75, 40, 63, 5}, /* 640x480@...z */
> + /* 640x480@...z */
> +
> + {30240, 640, 480, 67, 62, 75, 4}, /* 640x480@...z */
> + {27000, 720, 576, 50, 50, 54, 4}, /* 720x576@...z */
> + {25175, 640, 480, 60, 85, 107, 5}, /* 640x480@...z */
> + {25200, 640, 480, 60, 50, 63, 5}, /* 640x480@...z */
> + /* 720x480@...z */
> +};
> +
> +static void lsdc_pixel_pll_free(struct drm_device *ddev, void *data)
> +{
> + struct lsdc_pixpll *this = (struct lsdc_pixpll *)data;
> +
> + iounmap(this->mmio);
> +
> + kfree(this->priv);
> +
> + drm_dbg(ddev, "pixpll private data freed\n");
> +}
> +
> +/*
> + * ioremap the device dependent PLL registers
> + *
> + * @this: point to the object where this function is called from
> + */
> +static int lsdc_pixel_pll_setup(struct lsdc_pixpll * const this)
> +{
> + struct lsdc_pixpll_parms *pparms;
> +
> + this->mmio = ioremap(this->reg_base, this->reg_size);
> + if (IS_ERR_OR_NULL(this->mmio))
> + return -ENOMEM;
> +
> + pparms = kzalloc(sizeof(*pparms), GFP_KERNEL);
> + if (IS_ERR_OR_NULL(pparms))
> + return -ENOMEM;
> +
> + pparms->ref_clock = LSDC_PLL_REF_CLK;
> +
> + this->priv = pparms;
> +
> + return drmm_add_action_or_reset(this->ddev, lsdc_pixel_pll_free, this);
> +}
> +
> +/*
> + * Find a set of pll parameters from a static local table which avoid
> + * computing the pll parameter eachtime a modeset is triggered.
> + *
> + * @this: point to the object where this function is called from
> + * @clock: the desired output pixel clock, the unit is kHz
> + * @pout: point to where the parameters to store if found
> + *
> + * Return 0 if success, return -1 if not found.
> + */
> +static int lsdc_pixpll_find(struct lsdc_pixpll * const this,
> + unsigned int clock,
> + struct lsdc_pixpll_parms *pout)
> +{
> + unsigned int num = ARRAY_SIZE(pixpll_parms_table);
> + const struct clk_to_pixpll_parms_lookup_t *pt;
> + unsigned int i;
> +
> + for (i = 0; i < num; ++i) {
> + pt = &pixpll_parms_table[i];
> +
> + if (clock == pt->clock) {
> + pout->div_ref = pt->div_ref;
> + pout->loopc = pt->loopc;
> + pout->div_out = pt->div_out;
> +
> + return 0;
> + }
> + }
> +
> + drm_dbg_kms(this->ddev, "pixel clock %u: miss\n", clock);
> +
> + return -1;
> +}
> +
> +/*
> + * Find a set of pll parameters which have minimal difference with the
> + * desired pixel clock frequency. It does that by computing all of the
> + * possible combination. Compute the diff and find the combination with
> + * minimal diff.
> + *
> + * clock_out = refclk / div_ref * loopc / div_out
> + *
> + * refclk is determined by the oscillator mounted on motherboard(100MHz
> + * in almost all board)
> + *
> + * @this: point to the object from where this function is called
> + * @clock: the desired output pixel clock, the unit is kHz
> + * @pout: point to the out struct of lsdc_pixpll_parms
> + *
> + * Return 0 if a set of parameter is found, otherwise return the error
> + * between clock_kHz we wanted and the most closest candidate with it.
> + */
> +static int lsdc_pixel_pll_compute(struct lsdc_pixpll * const this,
> + unsigned int clock,
> + struct lsdc_pixpll_parms *pout)
> +{
> + struct lsdc_pixpll_parms *pparms = this->priv;
> + unsigned int refclk = pparms->ref_clock;
> + const unsigned int tolerance = 1000;
> + unsigned int min = tolerance;
> + unsigned int div_out, loopc, div_ref;
> + unsigned int computed;
> +
> + if (!lsdc_pixpll_find(this, clock, pout))
> + return 0;
> +
> + for (div_out = 6; div_out < 64; div_out++) {
> + for (div_ref = 3; div_ref < 6; div_ref++) {
> + for (loopc = 6; loopc < 161; loopc++) {
> + unsigned int diff = 0;
> +
> + if (loopc < 12 * div_ref)
> + continue;
> + if (loopc > 32 * div_ref)
> + continue;
> +
> + computed = refclk / div_ref * loopc / div_out;
> +
> + if (clock >= computed)
> + diff = clock - computed;
> + else
> + diff = computed - clock;
> +
> + if (diff < min) {
> + min = diff;
> + pparms->div_ref = div_ref;
> + pparms->div_out = div_out;
> + pparms->loopc = loopc;
> +
> + if (diff == 0) {
> + *pout = *pparms;
> + return 0;
> + }
> + }
> + }
> + }
> + }
> +
> + /* still acceptable */
> + if (min < tolerance) {
> + *pout = *pparms;
> + return 0;
> + }
> +
> + drm_dbg(this->ddev, "can't find suitable params for %u khz\n", clock);
> +
> + return min;
> +}
> +
> +/* Pixel pll hardware related ops, per display pipe */
> +
> +static void __pixpll_rreg(struct lsdc_pixpll *this,
> + union lsdc_pixpll_reg_bitmap *dst)
> +{
> +#if defined(CONFIG_64BIT)
> + dst->d = readq(this->mmio);
> +#else
> + dst->w[0] = readl(this->mmio);
> + dst->w[1] = readl(this->mmio + 4);
> +#endif
> +}
> +
> +static void __pixpll_wreg(struct lsdc_pixpll *this,
> + union lsdc_pixpll_reg_bitmap *src)
> +{
> +#if defined(CONFIG_64BIT)
> + writeq(src->d, this->mmio);
> +#else
> + writel(src->w[0], this->mmio);
> + writel(src->w[1], this->mmio + 4);
> +#endif
> +}
> +
> +static void __pixpll_ops_powerup(struct lsdc_pixpll * const this)
> +{
> + union lsdc_pixpll_reg_bitmap pixpll_reg;
> +
> + __pixpll_rreg(this, &pixpll_reg);
> +
> + pixpll_reg.bitmap.powerdown = 0;
> +
> + __pixpll_wreg(this, &pixpll_reg);
> +}
> +
> +static void __pixpll_ops_powerdown(struct lsdc_pixpll * const this)
> +{
> + union lsdc_pixpll_reg_bitmap pixpll_reg;
> +
> + __pixpll_rreg(this, &pixpll_reg);
> +
> + pixpll_reg.bitmap.powerdown = 1;
> +
> + __pixpll_wreg(this, &pixpll_reg);
> +}
> +
> +static void __pixpll_ops_on(struct lsdc_pixpll * const this)
> +{
> + union lsdc_pixpll_reg_bitmap pixpll_reg;
> +
> + __pixpll_rreg(this, &pixpll_reg);
> +
> + pixpll_reg.bitmap.sel_out = 1;
> +
> + __pixpll_wreg(this, &pixpll_reg);
> +}
> +
> +static void __pixpll_ops_off(struct lsdc_pixpll * const this)
> +{
> + union lsdc_pixpll_reg_bitmap pixpll_reg;
> +
> + __pixpll_rreg(this, &pixpll_reg);
> +
> + pixpll_reg.bitmap.sel_out = 0;
> +
> + __pixpll_wreg(this, &pixpll_reg);
> +}
> +
> +static void __pixpll_ops_bypass(struct lsdc_pixpll * const this)
> +{
> + union lsdc_pixpll_reg_bitmap pixpll_reg;
> +
> + __pixpll_rreg(this, &pixpll_reg);
> +
> + pixpll_reg.bitmap.bypass = 1;
> +
> + __pixpll_wreg(this, &pixpll_reg);
> +}
> +
> +static void __pixpll_ops_unbypass(struct lsdc_pixpll * const this)
> +{
> + union lsdc_pixpll_reg_bitmap pixpll_reg;
> +
> + __pixpll_rreg(this, &pixpll_reg);
> +
> + pixpll_reg.bitmap.bypass = 0;
> +
> + __pixpll_wreg(this, &pixpll_reg);
> +}
> +
> +static void __pixpll_ops_untoggle_param(struct lsdc_pixpll * const this)
> +{
> + union lsdc_pixpll_reg_bitmap pixpll_reg;
> +
> + __pixpll_rreg(this, &pixpll_reg);
> +
> + pixpll_reg.bitmap.set_param = 0;
> +
> + __pixpll_wreg(this, &pixpll_reg);
> +}
> +
> +static void __pixpll_ops_set_param(struct lsdc_pixpll * const this,
> + struct lsdc_pixpll_parms const *p)
> +{
> + union lsdc_pixpll_reg_bitmap pixpll_reg;
> +
> + __pixpll_rreg(this, &pixpll_reg);
> +
> + pixpll_reg.bitmap.div_ref = p->div_ref;
> + pixpll_reg.bitmap.loopc = p->loopc;
> + pixpll_reg.bitmap.div_out = p->div_out;
> +
> + __pixpll_wreg(this, &pixpll_reg);
> +}
> +
> +static void __pixpll_ops_toggle_param(struct lsdc_pixpll * const this)
> +{
> + union lsdc_pixpll_reg_bitmap pixpll_reg;
> +
> + __pixpll_rreg(this, &pixpll_reg);
> +
> + pixpll_reg.bitmap.set_param = 1;
> +
> + __pixpll_wreg(this, &pixpll_reg);
> +}
> +
> +static void __pixpll_ops_wait_locked(struct lsdc_pixpll * const this)
> +{
> + union lsdc_pixpll_reg_bitmap pixpll_reg;
> + unsigned int counter = 0;
> +
> + do {
> + __pixpll_rreg(this, &pixpll_reg);
> +
> + if (pixpll_reg.bitmap.locked)
> + break;
> +
> + ++counter;
> + } while (counter < 2000);
> +
> + drm_dbg(this->ddev, "%u loop waited\n", counter);
> +}
> +
> +/*
> + * Update the pll parameters to hardware, target to the pixpll in ls7a1000
> + *
> + * @this: point to the object from which this function is called
> + * @pin: point to the struct of lsdc_pixpll_parms passed in
> + *
> + * return 0 if successful.
> + */
> +static int lsdc_pixpll_update(struct lsdc_pixpll * const this,
> + struct lsdc_pixpll_parms const *pin)
> +{
> + __pixpll_ops_bypass(this);
> +
> + __pixpll_ops_off(this);
> +
> + __pixpll_ops_powerdown(this);
> +
> + __pixpll_ops_toggle_param(this);
> +
> + __pixpll_ops_set_param(this, pin);
> +
> + __pixpll_ops_untoggle_param(this);
> +
> + __pixpll_ops_powerup(this);
> +
> + udelay(2);
> +
> + __pixpll_ops_wait_locked(this);
> +
> + __pixpll_ops_on(this);
> +
> + __pixpll_ops_unbypass(this);
> +
> + return 0;
> +}
> +
> +static unsigned int lsdc_pixpll_get_freq(struct lsdc_pixpll * const this)
> +{
> + struct lsdc_pixpll_parms *ppar = this->priv;
> + union lsdc_pixpll_reg_bitmap pix_pll_reg;
> + unsigned int freq;
> +
> + __pixpll_rreg(this, &pix_pll_reg);
> +
> + ppar->div_ref = pix_pll_reg.bitmap.div_ref;
> + ppar->loopc = pix_pll_reg.bitmap.loopc;
> + ppar->div_out = pix_pll_reg.bitmap.div_out;
> +
> + freq = ppar->ref_clock / ppar->div_ref * ppar->loopc / ppar->div_out;
> +
> + return freq;
> +}
> +
> +static void lsdc_pixpll_print(struct lsdc_pixpll * const this,
> + struct drm_printer *p)
> +{
> + struct lsdc_pixpll_parms *parms = this->priv;
> +
> + drm_printf(p, "div_ref: %u, loopc: %u, div_out: %u\n",
> + parms->div_ref, parms->loopc, parms->div_out);
> +}
> +
> +/*
> + * LS7A1000, LS7A2000 and ls2k2000's pixel pll setting register is same,
> + * we take this as default, create a new instance if a different model is
> + * introduced.
> + */
> +static const struct lsdc_pixpll_funcs default_pixpll_funcs = {
> + .setup = lsdc_pixel_pll_setup,
> + .compute = lsdc_pixel_pll_compute,
> + .update = lsdc_pixpll_update,
> + .get_rate = lsdc_pixpll_get_freq,
> + .print = lsdc_pixpll_print,
> +};
> +
> +/* pixel pll initialization */
> +
> +int lsdc_pixpll_init(struct lsdc_pixpll * const this,
> + struct drm_device *ddev,
> + unsigned int index)
> +{
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + const struct lsdc_desc *descp = ldev->descp;
> + const struct loongson_gfx_desc *gfx = to_loongson_gfx(descp);
> +
> + this->ddev = ddev;
> + this->reg_size = 8;
> + this->reg_base = gfx->conf_reg_base + gfx->pixpll[index].reg_offset;
> + this->funcs = &default_pixpll_funcs;
> +
> + return this->funcs->setup(this);
> +}
> diff --git a/drivers/gpu/drm/loongson/lsdc_pixpll.h b/drivers/gpu/drm/loongson/lsdc_pixpll.h
> new file mode 100644
> index 000000000000..2f83e21d977d
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_pixpll.h
> @@ -0,0 +1,86 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#ifndef __LSDC_PIXPLL_H__
> +#define __LSDC_PIXPLL_H__
> +
> +#include <drm/drm_device.h>
> +
> +/*
> + * Loongson Pixel PLL hardware structure
> + *
> + * refclk: reference frequency, 100 MHz from external oscillator
> + * outclk: output frequency desired.
> + *
> + *
> + * L1 Fref Fvco L2
> + * refclk +-----------+ +------------------+ +---------+ outclk
> + * ---+---> | Prescaler | ---> | Clock Multiplier | ---> | divider | -------->
> + * | +-----------+ +------------------+ +---------+ ^
> + * | ^ ^ ^ |
> + * | | | | |
> + * | | | | |
> + * | div_ref loopc div_out |
> + * | |
> + * +---- bypass (bypass above software configurable clock if set) ----+
> + *
> + * outclk = refclk / div_ref * loopc / div_out;
> + *
> + * sel_out: PLL clock output selector(enable).
> + *
> + * If sel_out == 1, then enable output clock (turn On);
> + * If sel_out == 0, then disable output clock (turn Off);
> + *
> + * PLL working requirements:
> + *
> + * 1) 20 MHz <= refclk / div_ref <= 40Mhz
> + * 2) 1.2 GHz <= refclk /div_out * loopc <= 3.2 Ghz
> + */
> +
> +struct lsdc_pixpll_parms {
> + unsigned int ref_clock;
> + unsigned int div_ref;
> + unsigned int loopc;
> + unsigned int div_out;
> +};
> +
> +struct lsdc_pixpll;
> +
> +struct lsdc_pixpll_funcs {
> + int (*setup)(struct lsdc_pixpll * const this);
> +
> + int (*compute)(struct lsdc_pixpll * const this,
> + unsigned int clock,
> + struct lsdc_pixpll_parms *pout);
> +
> + int (*update)(struct lsdc_pixpll * const this,
> + struct lsdc_pixpll_parms const *pin);
> +
> + unsigned int (*get_rate)(struct lsdc_pixpll * const this);
> +
> + void (*print)(struct lsdc_pixpll * const this,
> + struct drm_printer *printer);
> +};
> +
> +struct lsdc_pixpll {
> + const struct lsdc_pixpll_funcs *funcs;
> +
> + struct drm_device *ddev;
> +
> + /* PLL register offset */
> + u32 reg_base;
> + /* PLL register size in bytes */
> + u32 reg_size;
> +
> + void __iomem *mmio;
> +
> + struct lsdc_pixpll_parms *priv;
> +};
> +
> +int lsdc_pixpll_init(struct lsdc_pixpll * const this,
> + struct drm_device *ddev,
> + unsigned int index);
> +
> +#endif
> diff --git a/drivers/gpu/drm/loongson/lsdc_plane.c b/drivers/gpu/drm/loongson/lsdc_plane.c
> new file mode 100644
> index 000000000000..4a18babe3736
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_plane.c
> @@ -0,0 +1,639 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#include <linux/delay.h>
> +
> +#include <drm/drm_atomic.h>
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_framebuffer.h>
> +#include <drm/drm_gem_atomic_helper.h>
> +#include <drm/drm_plane_helper.h>
> +
> +#include "lsdc_drv.h"
> +#include "lsdc_regs.h"
> +#include "lsdc_ttm.h"
> +
> +static const u32 lsdc_primary_formats[] = {
> + DRM_FORMAT_XRGB8888,
> +};
> +
> +static const u32 lsdc_cursor_formats[] = {
> + DRM_FORMAT_ARGB8888,
> +};
> +
> +static const u64 lsdc_fb_format_modifiers[] = {
> + DRM_FORMAT_MOD_LINEAR,
> + DRM_FORMAT_MOD_INVALID
> +};
> +
> +static unsigned int lsdc_get_fb_offset(struct drm_framebuffer *fb,
> + struct drm_plane_state *state)
> +{
> + unsigned int offset = fb->offsets[0];
> +
> + offset += fb->format->cpp[0] * (state->src_x >> 16);
> + offset += fb->pitches[0] * (state->src_y >> 16);
> +
> + return offset;
> +}
> +
> +static u64 lsdc_fb_dma_base_addr(struct drm_framebuffer *fb)
> +{
> + struct lsdc_bo *lbo = gem_to_lsdc_bo(fb->obj[0]);
> + struct lsdc_device *ldev = to_lsdc(fb->dev);
> +
> + return lsdc_bo_gpu_offset(lbo) + ldev->vram_base;
> +}
> +
> +static int lsdc_primary_atomic_check(struct drm_plane *plane,
> + struct drm_atomic_state *state)
> +{
> + struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane);
> + struct drm_crtc *crtc = new_plane_state->crtc;
> + struct drm_crtc_state *new_crtc_state;
> +
> + if (!crtc)
> + return 0;
> +
> + new_crtc_state = drm_atomic_get_new_crtc_state(state, crtc);
> +
> + return drm_atomic_helper_check_plane_state(new_plane_state,
> + new_crtc_state,
> + DRM_PLANE_NO_SCALING,
> + DRM_PLANE_NO_SCALING,
> + false,
> + true);
> +}
> +
> +static void lsdc_primary_atomic_update(struct drm_plane *plane,
> + struct drm_atomic_state *state)
> +{
> + struct lsdc_primary *primary = to_lsdc_primary(plane);
> + struct drm_plane_state *old_plane_state = drm_atomic_get_old_plane_state(state, plane);
> + struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane);
> + struct drm_framebuffer *new_fb = new_plane_state->fb;
> + struct drm_framebuffer *old_fb = old_plane_state->fb;
> + const struct lsdc_primary_plane_ops *hw_ops = primary->ops;
> + u64 fb_addr;
> +
> + fb_addr = lsdc_fb_dma_base_addr(new_fb);
> + fb_addr += lsdc_get_fb_offset(new_fb, new_plane_state);
> +
> + drm_dbg(plane->dev, "fb dma addr: %llx\n", fb_addr);
> +
> + hw_ops->update_fb_addr(primary, fb_addr);
> + hw_ops->update_fb_stride(primary, new_fb->pitches[0]);
> +
> + if (!old_fb || old_fb->format != new_fb->format)
> + hw_ops->update_fb_format(primary, new_fb->format);
> +}
> +
> +static void lsdc_primary_atomic_disable(struct drm_plane *plane,
> + struct drm_atomic_state *state)
> +{
> + /* Do nothing, just prevent call into atomic_update().
> + * Writing the format as LSDC_PF_NONE can disable the primary,
> + * But it seems not necessary...
> + */
> + drm_dbg(plane->dev, "%s disabled\n", plane->name);
> +}
> +
> +static int lsdc_plane_prepare_fb(struct drm_plane *plane,
> + struct drm_plane_state *new_state)
> +{
> + struct drm_framebuffer *fb = new_state->fb;
> + struct lsdc_bo *lbo;
> + u64 gpu_vaddr;
> + int ret;
> +
> + if (!fb)
> + return 0;
> +
> + lbo = gem_to_lsdc_bo(fb->obj[0]);
> +
> + ret = lsdc_bo_reserve(lbo);
> + if (unlikely(ret)) {
> + drm_err(plane->dev, "bo %p reserve failed\n", lbo);
> + return ret;
> + }
> +
> + ret = lsdc_bo_pin(lbo, LSDC_GEM_DOMAIN_VRAM, &gpu_vaddr);
> +
> + lsdc_bo_unreserve(lbo);
> +
> + if (unlikely(ret)) {
> + drm_err(plane->dev, "bo %p pin failed\n", lbo);
> + return ret;
> + }
> +
> + lsdc_bo_ref(lbo);
> +
> + if (plane->type != DRM_PLANE_TYPE_CURSOR)
> + drm_dbg(plane->dev, "%s[%p] pin at 0x%llx, bo size: %zu\n",
> + plane->name, lbo, gpu_vaddr, lsdc_bo_size(lbo));
> +
> + return drm_gem_plane_helper_prepare_fb(plane, new_state);
> +}
> +
> +static void lsdc_plane_cleanup_fb(struct drm_plane *plane,
> + struct drm_plane_state *old_state)
> +{
> + struct drm_framebuffer *fb = old_state->fb;
> + struct lsdc_bo *lbo;
> + int ret;
> +
> + if (!fb)
> + return;
> +
> + lbo = gem_to_lsdc_bo(fb->obj[0]);
> +
> + ret = lsdc_bo_reserve(lbo);
> + if (unlikely(ret)) {
> + drm_err(plane->dev, "%p reserve failed\n", lbo);
> + return;
> + }
> +
> + lsdc_bo_unpin(lbo);
> +
> + lsdc_bo_unreserve(lbo);
> +
> + lsdc_bo_unref(lbo);
> +
> + if (plane->type != DRM_PLANE_TYPE_CURSOR)
> + drm_dbg(plane->dev, "%s unpin\n", plane->name);
> +}
> +
> +static const struct drm_plane_helper_funcs lsdc_primary_helper_funcs = {
> + .prepare_fb = lsdc_plane_prepare_fb,
> + .cleanup_fb = lsdc_plane_cleanup_fb,
> + .atomic_check = lsdc_primary_atomic_check,
> + .atomic_update = lsdc_primary_atomic_update,
> + .atomic_disable = lsdc_primary_atomic_disable,
> +};
> +
> +static int lsdc_cursor_atomic_check(struct drm_plane *plane,
> + struct drm_atomic_state *state)
> +{
> + struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane);
> + struct drm_crtc *crtc = new_plane_state->crtc;
> + struct drm_crtc_state *new_crtc_state;
> +
> + if (!crtc)
> + return 0;
> +
> + new_crtc_state = drm_atomic_get_new_crtc_state(state, crtc);
> +
> + return drm_atomic_helper_check_plane_state(new_plane_state,
> + new_crtc_state,
> + DRM_PLANE_NO_SCALING,
> + DRM_PLANE_NO_SCALING,
> + true,
> + true);
> +}
> +
> +static void ls7a1000_cursor_atomic_update(struct drm_plane *plane,
> + struct drm_atomic_state *state)
> +{
> + struct lsdc_cursor *cursor = to_lsdc_cursor(plane);
> + struct drm_plane_state *old_plane_state = drm_atomic_get_old_plane_state(state, plane);
> + struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane);
> + struct drm_framebuffer *new_fb = new_plane_state->fb;
> + struct drm_framebuffer *old_fb = old_plane_state->fb;
> + const struct lsdc_cursor_plane_ops *hw_ops = cursor->ops;
> + u64 addr = lsdc_fb_dma_base_addr(new_fb);
> +
> + hw_ops->update_position(cursor, new_plane_state->crtc_x, new_plane_state->crtc_y);
> +
> + if (!old_fb || new_fb != old_fb)
> + hw_ops->update_bo_addr(cursor, addr);
> +
> + hw_ops->update_cfg(cursor, CURSOR_SIZE_32X32, CURSOR_FORMAT_ARGB8888);
> +}
> +
> +static void ls7a1000_cursor_atomic_disable(struct drm_plane *plane,
> + struct drm_atomic_state *state)
> +{
> + struct lsdc_cursor *cursor = to_lsdc_cursor(plane);
> + const struct lsdc_cursor_plane_ops *hw_ops = cursor->ops;
> +
> + hw_ops->update_cfg(cursor, CURSOR_SIZE_32X32, CURSOR_FORMAT_DISABLE);
> +}
> +
> +static const struct drm_plane_helper_funcs ls7a1000_cursor_helper_funcs = {
> + .prepare_fb = lsdc_plane_prepare_fb,
> + .cleanup_fb = lsdc_plane_cleanup_fb,
> + .atomic_check = lsdc_cursor_atomic_check,
> + .atomic_update = ls7a1000_cursor_atomic_update,
> + .atomic_disable = ls7a1000_cursor_atomic_disable,
> +};
> +
> +/* update the format, size and location of the cursor */
> +static void ls7a2000_cursor_atomic_update(struct drm_plane *plane,
> + struct drm_atomic_state *state)
> +{
> + struct lsdc_cursor *cursor = to_lsdc_cursor(plane);
> + struct drm_plane_state *old_plane_state = drm_atomic_get_old_plane_state(state, plane);
> + struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane);
> + struct drm_framebuffer *new_fb = new_plane_state->fb;
> + struct drm_framebuffer *old_fb = old_plane_state->fb;
> + const struct lsdc_cursor_plane_ops *hw_ops = cursor->ops;
> + u64 addr = lsdc_fb_dma_base_addr(new_fb);
> +
> + hw_ops->update_position(cursor, new_plane_state->crtc_x, new_plane_state->crtc_y);
> +
> + if (!old_fb || new_fb != old_fb)
> + hw_ops->update_bo_addr(cursor, addr);
> +
> + hw_ops->update_cfg(cursor, CURSOR_SIZE_64X64, CURSOR_FORMAT_ARGB8888);
> +}
> +
> +static void ls7a2000_cursor_atomic_disable(struct drm_plane *plane,
> + struct drm_atomic_state *state)
> +{
> + struct lsdc_cursor *cursor = to_lsdc_cursor(plane);
> + const struct lsdc_cursor_plane_ops *hw_ops = cursor->ops;
> +
> + hw_ops->update_cfg(cursor, CURSOR_SIZE_64X64, CURSOR_FORMAT_DISABLE);
> +}
> +
> +static const struct drm_plane_helper_funcs ls7a2000_cursor_helper_funcs = {
> + .prepare_fb = lsdc_plane_prepare_fb,
> + .cleanup_fb = lsdc_plane_cleanup_fb,
> + .atomic_check = lsdc_cursor_atomic_check,
> + .atomic_update = ls7a2000_cursor_atomic_update,
> + .atomic_disable = ls7a2000_cursor_atomic_disable,
> +};
> +
> +static void lsdc_plane_atomic_print_state(struct drm_printer *p,
> + const struct drm_plane_state *state)
> +{
> + struct drm_framebuffer *fb = state->fb;
> + u64 addr;
> +
> + if (!fb)
> + return;
> +
> + addr = lsdc_fb_dma_base_addr(fb);
> +
> + drm_printf(p, "\tdma addr=%llx\n", addr);
> +}
> +
> +static const struct drm_plane_funcs lsdc_plane_funcs = {
> + .update_plane = drm_atomic_helper_update_plane,
> + .disable_plane = drm_atomic_helper_disable_plane,
> + .destroy = drm_plane_cleanup,
> + .reset = drm_atomic_helper_plane_reset,
> + .atomic_duplicate_state = drm_atomic_helper_plane_duplicate_state,
> + .atomic_destroy_state = drm_atomic_helper_plane_destroy_state,
> + .atomic_print_state = lsdc_plane_atomic_print_state,
> +};
> +
> +/* primary plane hardware related ops, for primary plane 0 */
> +
> +static void lsdc_primary0_update_fb_addr(struct lsdc_primary *primary, u64 fb_addr)
> +{
> + struct lsdc_device *ldev = primary->ldev;
> + u32 status;
> + u32 lo, hi;
> +
> + /* 40-bit width physical address bus */
> + lo = fb_addr & 0xFFFFFFFF;
> + hi = (fb_addr >> 32) & 0xFF;
> +
> + status = lsdc_rreg32(ldev, LSDC_CRTC0_CFG_REG);
> + if (status & FB_REG_IN_USING) {
> + lsdc_wreg32(ldev, LSDC_CRTC0_FB1_ADDR_LO_REG, lo);
> + lsdc_wreg32(ldev, LSDC_CRTC0_FB1_ADDR_HI_REG, hi);
> + } else {
> + lsdc_wreg32(ldev, LSDC_CRTC0_FB0_ADDR_LO_REG, lo);
> + lsdc_wreg32(ldev, LSDC_CRTC0_FB0_ADDR_HI_REG, hi);
> + }
> +}
> +
> +static void lsdc_primary0_update_fb_stride(struct lsdc_primary *primary, u32 stride)
> +{
> + struct lsdc_device *ldev = primary->ldev;
> +
> + lsdc_wreg32(ldev, LSDC_CRTC0_STRIDE_REG, stride);
> +}
> +
> +static void lsdc_primary0_update_fb_format(struct lsdc_primary *primary,
> + const struct drm_format_info *format)
> +{
> + struct lsdc_device *ldev = primary->ldev;
> + u32 status;
> +
> + status = lsdc_rreg32(ldev, LSDC_CRTC0_CFG_REG);
> +
> + /*
> + * TODO: add RGB565 support, only support XRBG8888 currently
> + */
> + status &= ~CFG_PIX_FMT_MASK;
> + status |= LSDC_PF_XRGB8888;
> +
> + lsdc_wreg32(ldev, LSDC_CRTC0_CFG_REG, status);
> +
> + udelay(9);
> +}
> +
> +/* primary plane hardware related ops, for primary plane 1 */
> +
> +static void lsdc_primary1_update_fb_addr(struct lsdc_primary *primary, u64 fb_addr)
> +{
> + struct lsdc_device *ldev = primary->ldev;
> + u32 status;
> + u32 lo, hi;
> +
> + /* 40-bit width physical address bus */
> + lo = fb_addr & 0xFFFFFFFF;
> + hi = (fb_addr >> 32) & 0xFF;
> +
> + status = lsdc_rreg32(ldev, LSDC_CRTC1_CFG_REG);
> + if (status & FB_REG_IN_USING) {
> + lsdc_wreg32(ldev, LSDC_CRTC1_FB1_ADDR_LO_REG, lo);
> + lsdc_wreg32(ldev, LSDC_CRTC1_FB1_ADDR_HI_REG, hi);
> + } else {
> + lsdc_wreg32(ldev, LSDC_CRTC1_FB0_ADDR_LO_REG, lo);
> + lsdc_wreg32(ldev, LSDC_CRTC1_FB0_ADDR_HI_REG, hi);
> + }
> +}
> +
> +static void lsdc_primary1_update_fb_stride(struct lsdc_primary *primary, u32 stride)
> +{
> + struct lsdc_device *ldev = primary->ldev;
> +
> + lsdc_wreg32(ldev, LSDC_CRTC1_STRIDE_REG, stride);
> +}
> +
> +static void lsdc_primary1_update_fb_format(struct lsdc_primary *primary,
> + const struct drm_format_info *format)
> +{
> + struct lsdc_device *ldev = primary->ldev;
> + u32 status;
> +
> + status = lsdc_rreg32(ldev, LSDC_CRTC1_CFG_REG);
> +
> + /*
> + * Only support XRBG8888 currently,
> + * TODO: add RGB565 support
> + */
> + status &= ~CFG_PIX_FMT_MASK;
> + status |= LSDC_PF_XRGB8888;
> +
> + lsdc_wreg32(ldev, LSDC_CRTC1_CFG_REG, status);
> +
> + udelay(9);
> +}
> +
> +static const struct lsdc_primary_plane_ops primary_hw_ops[2] = {
> + {
> + .update_fb_addr = lsdc_primary0_update_fb_addr,
> + .update_fb_stride = lsdc_primary0_update_fb_stride,
> + .update_fb_format = lsdc_primary0_update_fb_format,
> + },
> + {
> + .update_fb_addr = lsdc_primary1_update_fb_addr,
> + .update_fb_stride = lsdc_primary1_update_fb_stride,
> + .update_fb_format = lsdc_primary1_update_fb_format,
> + },
> +};
> +
> +/*
> + * Update location, format, enable and disable state of the cursor,
> + * For those who have two hardware cursor, cursor 0 is attach it to CRTC-0,
> + * cursor 1 is attached to CRTC-1. Compositing the primary and cursor plane
> + * is automatically done by hardware, the cursor is alway on the top of the
> + * primary. In other word, z-order is fixed in hardware and cannot be changed.
> + * For those old DC who has only one hardware cursor, we made it shared by
> + * the two screen, this works on extend screen mode.
> + */
> +
> +/* cursor plane related hardware ops, for cursor plane 0 */
> +
> +static void lsdc_cursor0_update_bo_addr(struct lsdc_cursor *cursor, u64 addr)
> +{
> + struct lsdc_device *ldev = cursor->ldev;
> +
> + /* 40-bit width physical address bus */
> + lsdc_wreg32(ldev, LSDC_CURSOR0_ADDR_HI_REG, (addr >> 32) & 0xFF);
> + lsdc_wreg32(ldev, LSDC_CURSOR0_ADDR_LO_REG, addr);
> +}
> +
> +static void lsdc_cursor0_update_position(struct lsdc_cursor *cursor, int x, int y)
> +{
> + struct lsdc_device *ldev = cursor->ldev;
> +
> + if (x < 0)
> + x = 0;
> +
> + if (y < 0)
> + y = 0;
> +
> + lsdc_wreg32(ldev, LSDC_CURSOR0_POSITION_REG, (y << 16) | x);
> +}
> +
> +static void lsdc_cursor0_update_cfg(struct lsdc_cursor *cursor,
> + enum lsdc_cursor_size cursor_size,
> + enum lsdc_cursor_format fmt)
> +{
> + struct lsdc_device *ldev = cursor->ldev;
> + u32 cfg;
> +
> + cfg = CURSOR_ON_CRTC0 << CURSOR_LOCATION_SHIFT |
> + cursor_size << CURSOR_SIZE_SHIFT |
> + fmt << CURSOR_FORMAT_SHIFT;
> +
> + lsdc_wreg32(ldev, LSDC_CURSOR0_CFG_REG, cfg);
> +}
> +
> +/* cursor plane related hardware ops, for cursor plane 1 */
> +
> +static void lsdc_cursor1_update_bo_addr(struct lsdc_cursor *cursor, u64 addr)
> +{
> + struct lsdc_device *ldev = cursor->ldev;
> +
> + /* 40-bit width physical address bus */
> + lsdc_wreg32(ldev, LSDC_CURSOR1_ADDR_HI_REG, (addr >> 32) & 0xFF);
> + lsdc_wreg32(ldev, LSDC_CURSOR1_ADDR_LO_REG, addr);
> +}
> +
> +static void lsdc_cursor1_update_position(struct lsdc_cursor *cursor, int x, int y)
> +{
> + struct lsdc_device *ldev = cursor->ldev;
> +
> + if (x < 0)
> + x = 0;
> +
> + if (y < 0)
> + y = 0;
> +
> + lsdc_wreg32(ldev, LSDC_CURSOR1_POSITION_REG, (y << 16) | x);
> +}
> +
> +static void lsdc_cursor1_update_cfg(struct lsdc_cursor *cursor,
> + enum lsdc_cursor_size cursor_size,
> + enum lsdc_cursor_format fmt)
> +{
> + struct lsdc_device *ldev = cursor->ldev;
> + u32 cfg;
> +
> + cfg = CURSOR_ON_CRTC1 << CURSOR_LOCATION_SHIFT |
> + cursor_size << CURSOR_SIZE_SHIFT |
> + fmt << CURSOR_FORMAT_SHIFT;
> +
> + lsdc_wreg32(ldev, LSDC_CURSOR1_CFG_REG, cfg);
> +}
> +
> +static const struct lsdc_cursor_plane_ops ls7a2000_cursor_hw_ops[2] = {
> + {
> + .update_bo_addr = lsdc_cursor0_update_bo_addr,
> + .update_cfg = lsdc_cursor0_update_cfg,
> + .update_position = lsdc_cursor0_update_position,
> + },
> + {
> + .update_bo_addr = lsdc_cursor1_update_bo_addr,
> + .update_cfg = lsdc_cursor1_update_cfg,
> + .update_position = lsdc_cursor1_update_position,
> + },
> +};
> +
> +/* quirks for cursor 1, only for old loongson display controller device */
> +
> +static void lsdc_cursor1_update_bo_addr_quirk(struct lsdc_cursor *cursor, u64 addr)
> +{
> + struct lsdc_device *ldev = cursor->ldev;
> +
> + /* 40-bit width physical address bus */
> + lsdc_wreg32(ldev, LSDC_CURSOR0_ADDR_HI_REG, (addr >> 32) & 0xFF);
> + lsdc_wreg32(ldev, LSDC_CURSOR0_ADDR_LO_REG, addr);
> +}
> +
> +static void lsdc_cursor1_update_position_quirk(struct lsdc_cursor *cursor, int x, int y)
> +{
> + struct lsdc_device *ldev = cursor->ldev;
> +
> + if (x < 0)
> + x = 0;
> +
> + if (y < 0)
> + y = 0;
> +
> + lsdc_wreg32(ldev, LSDC_CURSOR0_POSITION_REG, (y << 16) | x);
> +}
> +
> +static void lsdc_cursor1_update_cfg_quirk(struct lsdc_cursor *cursor,
> + enum lsdc_cursor_size cursor_size,
> + enum lsdc_cursor_format fmt)
> +{
> + struct lsdc_device *ldev = cursor->ldev;
> + u32 cfg;
> +
> + cfg = CURSOR_ON_CRTC1 << CURSOR_LOCATION_SHIFT |
> + cursor_size << CURSOR_SIZE_SHIFT |
> + fmt << CURSOR_FORMAT_SHIFT;
> +
> + lsdc_wreg32(ldev, LSDC_CURSOR0_CFG_REG, cfg);
> +}
> +
> +static const struct lsdc_cursor_plane_ops ls7a1000_cursor_hw_ops[2] = {
> + {
> + .update_bo_addr = lsdc_cursor0_update_bo_addr,
> + .update_cfg = lsdc_cursor0_update_cfg,
> + .update_position = lsdc_cursor0_update_position,
> + },
> + {
> + .update_bo_addr = lsdc_cursor1_update_bo_addr_quirk,
> + .update_cfg = lsdc_cursor1_update_cfg_quirk,
> + .update_position = lsdc_cursor1_update_position_quirk,
> + },
> +};
> +
> +int lsdc_primary_plane_init(struct drm_device *ddev,
> + struct drm_plane *plane,
> + unsigned int index)
> +{
> + struct lsdc_primary *primary = to_lsdc_primary(plane);
> + int ret;
> +
> + ret = drm_universal_plane_init(ddev,
> + plane,
> + 1 << index,
> + &lsdc_plane_funcs,
> + lsdc_primary_formats,
> + ARRAY_SIZE(lsdc_primary_formats),
> + lsdc_fb_format_modifiers,
> + DRM_PLANE_TYPE_PRIMARY,
> + "primary-%u",
> + index);
> + if (ret)
> + return ret;
> +
> + drm_plane_helper_add(plane, &lsdc_primary_helper_funcs);
> +
> + primary->ldev = to_lsdc(ddev);
> + primary->ops = &primary_hw_ops[index];
> +
> + return 0;
> +}
> +
> +int ls7a1000_cursor_plane_init(struct drm_device *ddev,
> + struct drm_plane *plane,
> + unsigned int index)
> +{
> + struct lsdc_cursor *cursor = to_lsdc_cursor(plane);
> +
> + int ret;
> +
> + ret = drm_universal_plane_init(ddev,
> + plane,
> + 1 << index,
> + &lsdc_plane_funcs,
> + lsdc_cursor_formats,
> + ARRAY_SIZE(lsdc_cursor_formats),
> + lsdc_fb_format_modifiers,
> + DRM_PLANE_TYPE_CURSOR,
> + "cursor-%u",
> + index);
> + if (ret)
> + return ret;
> +
> + cursor->ldev = to_lsdc(ddev);
> + cursor->ops = &ls7a1000_cursor_hw_ops[index];
> +
> + drm_plane_helper_add(plane, &ls7a1000_cursor_helper_funcs);
> +
> + return 0;
> +}
> +
> +/* The hardware cursors become normal since ls7a2000(including ls2k2000) */
> +
> +int ls7a2000_cursor_plane_init(struct drm_device *ddev,
> + struct drm_plane *plane,
> + unsigned int index)
> +{
> + struct lsdc_cursor *cursor = to_lsdc_cursor(plane);
> +
> + int ret;
> +
> + ret = drm_universal_plane_init(ddev,
> + plane,
> + 1 << index,
> + &lsdc_plane_funcs,
> + lsdc_cursor_formats,
> + ARRAY_SIZE(lsdc_cursor_formats),
> + lsdc_fb_format_modifiers,
> + DRM_PLANE_TYPE_CURSOR,
> + "cursor-%u",
> + index);
> + if (ret)
> + return ret;
> +
> + cursor->ldev = to_lsdc(ddev);
> + cursor->ops = &ls7a2000_cursor_hw_ops[index];
> +
> + drm_plane_helper_add(plane, &ls7a2000_cursor_helper_funcs);
> +
> + return 0;
> +}
> diff --git a/drivers/gpu/drm/loongson/lsdc_probe.c b/drivers/gpu/drm/loongson/lsdc_probe.c
> new file mode 100644
> index 000000000000..06fc2a63110b
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_probe.c
> @@ -0,0 +1,56 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#include "lsdc_drv.h"
> +#include "lsdc_probe.h"
> +
> +/*
> + * Processor ID (implementation) values for bits 15:8 of the PRID register.
> + */
> +#define LOONGSON_CPU_IMP_MASK 0xff00
> +#define LOONGSON_CPU_IMP_SHIFT 8
> +
> +#define LOONGARCH_CPU_IMP_LS2K1000 0xa0
> +#define LOONGARCH_CPU_IMP_LS2K2000 0xb0
> +#define LOONGARCH_CPU_IMP_LS3A5000 0xc0
> +
> +#define LOONGSON_CPU_MIPS_IMP_LS2K 0x61 /* Loongson 2K Mips series SoC */
> +
> +/*
> + * Particular Revision values for bits 7:0 of the PRID register.
> + */
> +#define LOONGSON_CPU_REV_MASK 0x00ff
> +
> +#define LOONGARCH_CPUCFG_PRID_REG 0x0
> +
> +/*
> + * We can achieve fine control with the information about the host.
> + */
> +
> +unsigned int loongson_cpu_get_prid(u8 *imp, u8 *rev)
> +{
> + unsigned int prid = 0;
> +
> +#if defined(__loongarch__)
> + __asm__ volatile("cpucfg %0, %1\n\t"
> + : "=&r"(prid)
> + : "r"(LOONGARCH_CPUCFG_PRID_REG)
> + );
> +#endif
> +
> +#if defined(__mips__)
> + __asm__ volatile("mfc0\t%0, $15\n\t"
> + : "=r" (prid)
> + );
> +#endif
> +
> + if (imp)
> + *imp = (prid & LOONGSON_CPU_IMP_MASK) >> LOONGSON_CPU_IMP_SHIFT;
> +
> + if (rev)
> + *rev = prid & LOONGSON_CPU_REV_MASK;
> +
> + return prid;
> +}
> diff --git a/drivers/gpu/drm/loongson/lsdc_probe.h b/drivers/gpu/drm/loongson/lsdc_probe.h
> new file mode 100644
> index 000000000000..68ae93f90b67
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_probe.h
> @@ -0,0 +1,12 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#ifndef __LSDC_PROBE_H__
> +#define __LSDC_PROBE_H__
> +
> +/* Helpers for chip detection */
> +unsigned int loongson_cpu_get_prid(u8 *impl, u8 *rev);
> +
> +#endif
> diff --git a/drivers/gpu/drm/loongson/lsdc_regs.h b/drivers/gpu/drm/loongson/lsdc_regs.h
> new file mode 100644
> index 000000000000..4ae8fd7b0add
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_regs.h
> @@ -0,0 +1,400 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#ifndef __LSDC_REGS_H__
> +#define __LSDC_REGS_H__
> +
> +#include <linux/bitops.h>
> +#include <linux/types.h>
> +
> +/*
> + * PIXEL PLL Reference clock
> + */
> +#define LSDC_PLL_REF_CLK 100000 /* kHz */
> +
> +/*
> + * Those PLL registers are relative to LSxxxxx_CFG_REG_BASE. xxxxx = 7A1000,
> + * 7A2000, 2K2000, 2K1000 etc.
> + */
> +
> +/* LS7A1000 */
> +
> +#define LS7A1000_PIXPLL0_REG 0x04B0
> +#define LS7A1000_PIXPLL1_REG 0x04C0
> +
> +/* The DC, GPU, Graphic Memory Controller share the single gfxpll */
> +#define LS7A1000_PLL_GFX_REG 0x0490
> +
> +#define LS7A1000_CONF_REG_BASE 0x10010000
> +
> +/* LS7A2000 */
> +
> +#define LS7A2000_PIXPLL0_REG 0x04B0
> +#define LS7A2000_PIXPLL1_REG 0x04C0
> +
> +/* The DC, GPU, Graphic Memory Controller share the single gfxpll */
> +#define LS7A2000_PLL_GFX_REG 0x0490
> +
> +#define LS7A2000_CONF_REG_BASE 0x10010000
> +
> +/* For LSDC_CRTCx_CFG_REG */
> +#define CFG_PIX_FMT_MASK GENMASK(2, 0)
> +
> +enum lsdc_pixel_format {
> + LSDC_PF_NONE = 0,
> + LSDC_PF_XRGB444 = 1, /* [12 bits] */
> + LSDC_PF_XRGB555 = 2, /* [15 bits] */
> + LSDC_PF_XRGB565 = 3, /* RGB [16 bits] */
> + LSDC_PF_XRGB8888 = 4, /* XRGB [32 bits] */
> +};
> +
> +/*
> + * Each crtc has two set fb address registers usable, FB_REG_IN_USING bit of
> + * LSDC_CRTCx_CFG_REG indicate which fb address register is in using by the
> + * CRTC currently. CFG_PAGE_FLIP is used to trigger the switch, the switching
> + * will be finished at the very next vblank. Trigger it again if you want to
> + * switch back.
> + *
> + * If FB0_ADDR_REG is in using, we write the address to FB0_ADDR_REG,
> + * if FB1_ADDR_REG is in using, we write the address to FB1_ADDR_REG.
> + */
> +#define CFG_PAGE_FLIP BIT(7)
> +#define CFG_OUTPUT_ENABLE BIT(8)
> +#define CFG_HW_CLONE BIT(9)
> +/* Indicate witch fb addr reg is in using, currently. read only */
> +#define FB_REG_IN_USING BIT(11)
> +#define CFG_GAMMA_EN BIT(12)
> +
> +/* The DC get soft reset if this bit changed from "1" to "0", active low */
> +#define CFG_RESET_N BIT(20)
> +
> +/*
> + * The DMA step of the DC in LS7A2000/LS2K2000 is configurable,
> + * setting those bits on ls7a1000 platform make no effect.
> + */
> +#define CFG_DMA_STEP_MASK GENMASK(17, 16)
> +#define CFG_DMA_STEP_SHIFT 16
> +enum lsdc_dma_steps {
> + LSDC_DMA_STEP_256_BYTES = 0,
> + LSDC_DMA_STEP_128_BYTES = 1,
> + LSDC_DMA_STEP_64_BYTES = 2,
> + LSDC_DMA_STEP_32_BYTES = 3,
> +};
> +
> +#define CFG_VALID_BITS_MASK GENMASK(20, 0)
> +
> +/* For LSDC_CRTCx_PANEL_CONF_REG */
> +#define PHY_CLOCK_POL BIT(9)
> +#define PHY_CLOCK_EN BIT(8)
> +#define PHY_DE_POL BIT(1)
> +#define PHY_DATA_EN BIT(0)
> +
> +/* For LSDC_CRTCx_HSYNC_REG */
> +#define HSYNC_INV BIT(31)
> +#define HSYNC_EN BIT(30)
> +#define HSYNC_END_MASK GENMASK(28, 16)
> +#define HSYNC_END_SHIFT 16
> +#define HSYNC_START_MASK GENMASK(12, 0)
> +#define HSYNC_START_SHIFT 0
> +
> +/* For LSDC_CRTCx_VSYNC_REG */
> +#define VSYNC_INV BIT(31)
> +#define VSYNC_EN BIT(30)
> +#define VSYNC_END_MASK GENMASK(27, 16)
> +#define VSYNC_END_SHIFT 16
> +#define VSYNC_START_MASK GENMASK(11, 0)
> +#define VSYNC_START_SHIFT 0
> +
> +/*********** CRTC0 & DISPLAY PIPE0 ***********/
> +#define LSDC_CRTC0_CFG_REG 0x1240
> +#define LSDC_CRTC0_FB0_ADDR_LO_REG 0x1260
> +#define LSDC_CRTC0_FB0_ADDR_HI_REG 0x15A0
> +#define LSDC_CRTC0_STRIDE_REG 0x1280
> +#define LSDC_CRTC0_FB_ORIGIN_REG 0x1300
> +#define LSDC_CRTC0_PANEL_CONF_REG 0x13C0
> +#define LSDC_CRTC0_HDISPLAY_REG 0x1400
> +#define LSDC_CRTC0_HSYNC_REG 0x1420
> +#define LSDC_CRTC0_VDISPLAY_REG 0x1480
> +#define LSDC_CRTC0_VSYNC_REG 0x14A0
> +#define LSDC_CRTC0_GAMMA_INDEX_REG 0x14E0
> +#define LSDC_CRTC0_GAMMA_DATA_REG 0x1500
> +#define LSDC_CRTC0_FB1_ADDR_LO_REG 0x1580
> +#define LSDC_CRTC0_FB1_ADDR_HI_REG 0x15C0
> +
> +/*********** CTRC1 & DISPLAY PIPE1 ***********/
> +#define LSDC_CRTC1_CFG_REG 0x1250
> +#define LSDC_CRTC1_FB0_ADDR_LO_REG 0x1270
> +#define LSDC_CRTC1_FB0_ADDR_HI_REG 0x15B0
> +#define LSDC_CRTC1_STRIDE_REG 0x1290
> +#define LSDC_CRTC1_FB_ORIGIN_REG 0x1310
> +#define LSDC_CRTC1_PANEL_CONF_REG 0x13D0
> +#define LSDC_CRTC1_HDISPLAY_REG 0x1410
> +#define LSDC_CRTC1_HSYNC_REG 0x1430
> +#define LSDC_CRTC1_VDISPLAY_REG 0x1490
> +#define LSDC_CRTC1_VSYNC_REG 0x14B0
> +#define LSDC_CRTC1_GAMMA_INDEX_REG 0x14F0
> +#define LSDC_CRTC1_GAMMA_DATA_REG 0x1510
> +#define LSDC_CRTC1_FB1_ADDR_LO_REG 0x1590
> +#define LSDC_CRTC1_FB1_ADDR_HI_REG 0x15D0
> +
> +/*
> + * All of the DC variants has the hardware which record the scan position
> + * of the CRTC, [31:16] : current X position, [15:0] : current Y position
> + */
> +#define LSDC_CRTC0_SCAN_POS_REG 0x14C0
> +#define LSDC_CRTC1_SCAN_POS_REG 0x14D0
> +
> +/*
> + * LS7A2000 has Sync Deviation register.
> + */
> +#define SYNC_DEVIATION_EN BIT(31)
> +#define SYNC_DEVIATION_NUM GENMASK(12, 0)
> +#define LSDC_CRTC0_SYNC_DEVIATION_REG 0x1B80
> +#define LSDC_CRTC1_SYNC_DEVIATION_REG 0x1B90
> +
> +/*
> + * In gross, LSDC_CRTC1_XXX_REG - LSDC_CRTC0_XXX_REG = 0x10, but not all of
> + * the registers obey this rule, LSDC_CURSORx_XXX_REG just don't honor this.
> + * This is the root cause we can't untangle the code by manpulating offset
> + * of the register access simply. Our hardware engineers are lack experiance
> + * when they design this...
> + */
> +#define CRTC_PIPE_OFFSET 0x10
> +
> +/*
> + * There is only one hardware cursor unit in LS7A1000 and LS2K1000, let
> + * CFG_HW_CLONE_EN bit be "1" could eliminate this embarrassment, we made
> + * it on custom clone mode application. While LS7A2000 has two hardware
> + * cursor unit which is good enough.
> + */
> +#define CURSOR_FORMAT_MASK GENMASK(1, 0)
> +#define CURSOR_FORMAT_SHIFT 0
> +enum lsdc_cursor_format {
> + CURSOR_FORMAT_DISABLE = 0,
> + CURSOR_FORMAT_MONOCHROME = 1, /* masked */
> + CURSOR_FORMAT_ARGB8888 = 2, /* A8R8G8B8 */
> +};
> +
> +/*
> + * LS7A1000 and LS2K1000 only support 32x32, LS2K2000 and LS7A2000 support
> + * 64x64, but it seems that setting this bit make no harms on LS7A1000, it
> + * just don't take effects.
> + */
> +#define CURSOR_SIZE_SHIFT 2
> +enum lsdc_cursor_size {
> + CURSOR_SIZE_32X32 = 0,
> + CURSOR_SIZE_64X64 = 1,
> +};
> +
> +#define CURSOR_LOCATION_SHIFT 4
> +enum lsdc_cursor_location {
> + CURSOR_ON_CRTC0 = 0,
> + CURSOR_ON_CRTC1 = 1,
> +};
> +
> +#define LSDC_CURSOR0_CFG_REG 0x1520
> +#define LSDC_CURSOR0_ADDR_LO_REG 0x1530
> +#define LSDC_CURSOR0_ADDR_HI_REG 0x15e0
> +#define LSDC_CURSOR0_POSITION_REG 0x1540 /* [31:16] Y, [15:0] X */
> +#define LSDC_CURSOR0_BG_COLOR_REG 0x1550 /* background color */
> +#define LSDC_CURSOR0_FG_COLOR_REG 0x1560 /* foreground color */
> +
> +#define LSDC_CURSOR1_CFG_REG 0x1670
> +#define LSDC_CURSOR1_ADDR_LO_REG 0x1680
> +#define LSDC_CURSOR1_ADDR_HI_REG 0x16e0
> +#define LSDC_CURSOR1_POSITION_REG 0x1690 /* [31:16] Y, [15:0] X */
> +#define LSDC_CURSOR1_BG_COLOR_REG 0x16A0 /* background color */
> +#define LSDC_CURSOR1_FG_COLOR_REG 0x16B0 /* foreground color */
> +
> +/*
> + * DC Interrupt Control Register, 32bit, Address Offset: 1570
> + *
> + * Bits 15:0 inidicate the interrupt status
> + * Bits 31:16 control enable interrupts corresponding to bit 15:0 or not
> + * Write 1 to enable, write 0 to disable
> + *
> + * RF: Read Finished
> + * IDBU: Internal Data Buffer Underflow
> + * IDBFU: Internal Data Buffer Fatal Underflow
> + * CBRF: Cursor Buffer Read Finished Flag, no use.
> + * FBRF0: CRTC-0 reading from its framebuffer finished.
> + * FBRF1: CRTC-1 reading from its framebuffer finished.
> + *
> + * +-------+--------------------------+-------+--------+--------+-------+
> + * | 31:27 | 26:16 | 15:11 | 10 | 9 | 8 |
> + * +-------+--------------------------+-------+--------+--------+-------+
> + * | N/A | Interrupt Enable Control | N/A | IDBFU0 | IDBFU1 | IDBU0 |
> + * +-------+--------------------------+-------+--------+--------+-------+
> + *
> + * +-------+-------+-------+------+--------+--------+--------+--------+
> + * | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
> + * +-------+-------+-------+------+--------+--------+--------+--------+
> + * | IDBU1 | FBRF0 | FBRF1 | CRRF | HSYNC0 | VSYNC0 | HSYNC1 | VSYNC1 |
> + * +-------+-------+-------+------+--------+--------+--------+--------+
> + *
> + * unfortunately, CRTC0's interrupt is mess with CRTC1's interrupt in one
> + * register again.
> + */
> +
> +#define LSDC_INT_REG 0x1570
> +
> +#define INT_CRTC0_VSYNC BIT(2)
> +#define INT_CRTC0_HSYNC BIT(3)
> +#define INT_CRTC0_RF BIT(6)
> +#define INT_CRTC0_IDBU BIT(8)
> +#define INT_CRTC0_IDBFU BIT(10)
> +
> +#define INT_CRTC1_VSYNC BIT(0)
> +#define INT_CRTC1_HSYNC BIT(1)
> +#define INT_CRTC1_RF BIT(5)
> +#define INT_CRTC1_IDBU BIT(7)
> +#define INT_CRTC1_IDBFU BIT(9)
> +
> +#define INT_CRTC0_VSYNC_EN BIT(18)
> +#define INT_CRTC0_HSYNC_EN BIT(19)
> +#define INT_CRTC0_RF_EN BIT(22)
> +#define INT_CRTC0_IDBU_EN BIT(24)
> +#define INT_CRTC0_IDBFU_EN BIT(26)
> +
> +#define INT_CRTC1_VSYNC_EN BIT(16)
> +#define INT_CRTC1_HSYNC_EN BIT(17)
> +#define INT_CRTC1_RF_EN BIT(21)
> +#define INT_CRTC1_IDBU_EN BIT(23)
> +#define INT_CRTC1_IDBFU_EN BIT(25)
> +
> +#define INT_STATUS_MASK GENMASK(15, 0)
> +
> +/*
> + * LS7A1000/LS7A2000 have 4 gpios which are used to emulated I2C.
> + * They are under control of the LS7A_DC_GPIO_DAT_REG and LS7A_DC_GPIO_DIR_REG
> + * register, Those GPIOs has no relationship whth the GPIO hardware on the
> + * bridge chip itself. Those offsets are relative to DC register base address
> + *
> + * LS2k1000 don't have those registers, they use hardware i2c or general GPIO
> + * emulated i2c from linux i2c subsystem.
> + *
> + * GPIO data register, address offset: 0x1650
> + * +---------------+-----------+-----------+
> + * | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 |
> + * +---------------+-----------+-----------+
> + * | | DVO1 | DVO0 |
> + * + N/A +-----------+-----------+
> + * | | SCL | SDA | SCL | SDA |
> + * +---------------+-----------+-----------+
> + */
> +#define LS7A_DC_GPIO_DAT_REG 0x1650
> +
> +/*
> + * GPIO Input/Output direction control register, address offset: 0x1660
> + */
> +#define LS7A_DC_GPIO_DIR_REG 0x1660
> +
> +/*
> + * LS7A2000 has two built-in HDMI Encoder and one VGA encoder
> + */
> +
> +/*
> + * Number of continuous packets may be present
> + * in HDMI hblank and vblank zone, should >= 48
> + */
> +#define LSDC_HDMI0_ZONE_REG 0x1700
> +#define LSDC_HDMI1_ZONE_REG 0x1710
> +
> +#define HDMI_H_ZONE_IDLE_SHIFT 0
> +#define HDMI_V_ZONE_IDLE_SHIFT 16
> +
> +/* HDMI Iterface Control Reg */
> +#define HDMI_INTERFACE_EN BIT(0)
> +#define HDMI_PACKET_EN BIT(1)
> +#define HDMI_AUDIO_EN BIT(2)
> +/*
> + * Preamble:
> + * Immediately preceding each video data period or data island period is the
> + * preamble. This is a sequence of eight identical control characters that
> + * indicate whether the upcoming data period is a video data period or is a
> + * data island. The values of CTL0, CTL1, CTL2, and CTL3 indicate the type of
> + * data period that follows.
> + */
> +#define HDMI_VIDEO_PREAMBLE_MASK GENMASK(7, 4)
> +#define HDMI_VIDEO_PREAMBLE_SHIFT 4
> +/* 1: hw i2c, 0: gpio emu i2c, shouldn't put in LSDC_HDMIx_INTF_CTRL_REG */
> +#define HW_I2C_EN BIT(8)
> +#define HDMI_CTL_PERIOD_MODE BIT(9)
> +#define LSDC_HDMI0_INTF_CTRL_REG 0x1720
> +#define LSDC_HDMI1_INTF_CTRL_REG 0x1730
> +
> +#define HDMI_PHY_EN BIT(0)
> +#define HDMI_PHY_RESET_N BIT(1)
> +#define HDMI_PHY_TERM_L_EN BIT(8)
> +#define HDMI_PHY_TERM_H_EN BIT(9)
> +#define HDMI_PHY_TERM_DET_EN BIT(10)
> +#define HDMI_PHY_TERM_STATUS BIT(11)
> +#define LSDC_HDMI0_PHY_CTRL_REG 0x1800
> +#define LSDC_HDMI1_PHY_CTRL_REG 0x1810
> +
> +/* High level duration need > 1us */
> +#define HDMI_PLL_ENABLE BIT(0)
> +#define HDMI_PLL_LOCKED BIT(16)
> +/* Bypass the software configured values, using default source from somewhere */
> +#define HDMI_PLL_BYPASS BIT(17)
> +
> +#define HDMI_PLL_IDF_SHIFT 1
> +#define HDMI_PLL_IDF_MASK GENMASK(5, 1)
> +#define HDMI_PLL_LF_SHIFT 6
> +#define HDMI_PLL_LF_MASK GENMASK(12, 6)
> +#define HDMI_PLL_ODF_SHIFT 13
> +#define HDMI_PLL_ODF_MASK GENMASK(15, 13)
> +#define LSDC_HDMI0_PHY_PLL_REG 0x1820
> +#define LSDC_HDMI1_PHY_PLL_REG 0x1830
> +
> +/* LS7A2000/LS2K2000 has hpd status reg, while the two hdmi's status
> + * located at the one register again.
> + */
> +#define LSDC_HDMI_HPD_STATUS_REG 0x1BA0
> +#define HDMI0_HPD_FLAG BIT(0)
> +#define HDMI1_HPD_FLAG BIT(1)
> +
> +#define LSDC_HDMI0_PHY_CAL_REG 0x18C0
> +#define LSDC_HDMI1_PHY_CAL_REG 0x18D0
> +
> +/* AVI InfoFrame */
> +#define LSDC_HDMI0_AVI_CONTENT0 0x18E0
> +#define LSDC_HDMI1_AVI_CONTENT0 0x18D0
> +#define LSDC_HDMI0_AVI_CONTENT1 0x1900
> +#define LSDC_HDMI1_AVI_CONTENT1 0x1910
> +#define LSDC_HDMI0_AVI_CONTENT2 0x1920
> +#define LSDC_HDMI1_AVI_CONTENT2 0x1930
> +#define LSDC_HDMI0_AVI_CONTENT3 0x1940
> +#define LSDC_HDMI1_AVI_CONTENT3 0x1950
> +
> +/* 1: enable avi infoframe packet, 0: disable avi infoframe packet */
> +#define AVI_PKT_ENABLE BIT(0)
> +/* 1: send one every two frame, 0: send one each frame */
> +#define AVI_PKT_SEND_FREQ BIT(1)
> +/*
> + * 1: write 1 to flush avi reg content0 ~ content3 to the packet to be send,
> + * The hardware will clear this bit automatically.
> + */
> +#define AVI_PKT_UPDATE BIT(2)
> +
> +#define LSDC_HDMI0_AVI_INFO_CRTL_REG 0x1960
> +#define LSDC_HDMI1_AVI_INFO_CRTL_REG 0x1970
> +
> +/*
> + * LS7A2000 has the hardware which count the number of vblank generated
> + */
> +#define LSDC_CRTC0_VSYNC_COUNTER_REG 0x1A00
> +#define LSDC_CRTC1_VSYNC_COUNTER_REG 0x1A10
> +
> +/*
> + * LS7A2000 has the audio hardware associate with the HDMI encoder.
> + */
> +#define LSDC_HDMI0_AUDIO_PLL_LO_REG 0x1A20
> +#define LSDC_HDMI1_AUDIO_PLL_LO_REG 0x1A30
> +
> +#define LSDC_HDMI0_AUDIO_PLL_HI_REG 0x1A40
> +#define LSDC_HDMI1_AUDIO_PLL_HI_REG 0x1A50
> +
> +#endif
> diff --git a/drivers/gpu/drm/loongson/lsdc_ttm.c b/drivers/gpu/drm/loongson/lsdc_ttm.c
> new file mode 100644
> index 000000000000..a792beeb4375
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_ttm.c
> @@ -0,0 +1,547 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#include <drm/drm_drv.h>
> +#include <drm/drm_file.h>
> +#include <drm/drm_gem.h>
> +#include <drm/drm_managed.h>
> +#include <drm/drm_prime.h>
> +
> +#include "lsdc_drv.h"
> +#include "lsdc_ttm.h"
> +
> +const char *lsdc_mem_type_to_str(uint32_t mem_type)
> +{
> + switch (mem_type) {
> + case TTM_PL_VRAM:
> + return "VRAM";
> + case TTM_PL_TT:
> + return "GTT";
> + case TTM_PL_SYSTEM:
> + return "SYSTEM";
> + default:
> + break;
> + }
> +
> + return "Unknown";
> +}
> +
> +static void lsdc_bo_set_placement(struct lsdc_bo *lbo, u32 domain)
> +{
> + u32 c = 0;
> + u32 pflags = 0;
> + u32 i;
> +
> + if (lbo->tbo.base.size <= PAGE_SIZE)
> + pflags |= TTM_PL_FLAG_TOPDOWN;
> +
> + lbo->placement.placement = lbo->placements;
> + lbo->placement.busy_placement = lbo->placements;
> +
> + if (domain & LSDC_GEM_DOMAIN_VRAM) {
> + lbo->placements[c].mem_type = TTM_PL_VRAM;
> + lbo->placements[c++].flags = pflags;
> + }
> +
> + if (domain & LSDC_GEM_DOMAIN_GTT) {
> + lbo->placements[c].mem_type = TTM_PL_TT;
> + lbo->placements[c++].flags = pflags;
> + }
> +
> + if (domain & LSDC_GEM_DOMAIN_SYSTEM) {
> + lbo->placements[c].mem_type = TTM_PL_SYSTEM;
> + lbo->placements[c++].flags = 0;
> + }
> +
> + if (!c) {
> + lbo->placements[c].mem_type = TTM_PL_SYSTEM;
> + lbo->placements[c++].flags = 0;
> + }
> +
> + lbo->placement.num_placement = c;
> + lbo->placement.num_busy_placement = c;
> +
> + for (i = 0; i < c; ++i) {
> + lbo->placements[i].fpfn = 0;
> + lbo->placements[i].lpfn = 0;
> + }
> +}
> +
> +static void lsdc_ttm_tt_destroy(struct ttm_device *bdev, struct ttm_tt *tt)
> +{
> + ttm_tt_fini(tt);
> + kfree(tt);
> +}
> +
> +static struct ttm_tt *
> +lsdc_ttm_tt_create(struct ttm_buffer_object *tbo, uint32_t page_flags)
> +{
> + struct ttm_tt *tt;
> + int ret;
> +
> + tt = kzalloc(sizeof(*tt), GFP_KERNEL);
> + if (!tt)
> + return NULL;
> +
> + ret = ttm_sg_tt_init(tt, tbo, page_flags, ttm_cached);
> + if (ret < 0) {
> + kfree(tt);
> + return NULL;
> + }
> +
> + return tt;
> +}
> +
> +static int lsdc_ttm_tt_populate(struct ttm_device *bdev,
> + struct ttm_tt *ttm,
> + struct ttm_operation_ctx *ctx)
> +{
> + bool slave = !!(ttm->page_flags & TTM_TT_FLAG_EXTERNAL);
> +
> + if (slave && ttm->sg) {
> + drm_prime_sg_to_dma_addr_array(ttm->sg,
> + ttm->dma_address,
> + ttm->num_pages);
> +
> + return 0;
> + }
> +
> + return ttm_pool_alloc(&bdev->pool, ttm, ctx);
> +}
> +
> +static void lsdc_ttm_tt_unpopulate(struct ttm_device *bdev,
> + struct ttm_tt *ttm)
> +{
> + bool slave = !!(ttm->page_flags & TTM_TT_FLAG_EXTERNAL);
> +
> + if (slave)
> + return;
> +
> + return ttm_pool_free(&bdev->pool, ttm);
> +}
> +
> +static void lsdc_bo_evict_flags(struct ttm_buffer_object *tbo,
> + struct ttm_placement *tplacement)
> +{
> + struct ttm_resource *resource = tbo->resource;
> + struct lsdc_bo *lbo = to_lsdc_bo(tbo);
> +
> + switch (resource->mem_type) {
> + case TTM_PL_VRAM:
> + lsdc_bo_set_placement(lbo, LSDC_GEM_DOMAIN_GTT);
> + break;
> + case TTM_PL_TT:
> + default:
> + lsdc_bo_set_placement(lbo, LSDC_GEM_DOMAIN_SYSTEM);
> + break;
> + }
> +
> + *tplacement = lbo->placement;
> +}
> +
> +static int lsdc_bo_move(struct ttm_buffer_object *tbo,
> + bool evict,
> + struct ttm_operation_ctx *ctx,
> + struct ttm_resource *new_mem,
> + struct ttm_place *hop)
> +{
> + struct drm_device *ddev = tbo->base.dev;
> + struct ttm_resource *old_mem = tbo->resource;
> + struct lsdc_bo *lbo = to_lsdc_bo(tbo);
> + int ret;
> +
> + if (unlikely(tbo->pin_count > 0)) {
> + drm_warn(ddev, "Can't move a pinned BO\n");
> + return -EINVAL;
> + }
> +
> + ret = ttm_bo_wait_ctx(tbo, ctx);
> + if (ret)
> + return ret;
> +
> + if (!old_mem) {
> + drm_dbg(ddev, "bo[%p] move: NULL to %s, size: %zu\n",
> + lbo, lsdc_mem_type_to_str(new_mem->mem_type),
> + lsdc_bo_size(lbo));
> + ttm_bo_move_null(tbo, new_mem);
> + return 0;
> + }
> +
> + if (old_mem->mem_type == TTM_PL_SYSTEM && !tbo->ttm) {
> + ttm_bo_move_null(tbo, new_mem);
> + drm_dbg(ddev, "bo[%p] move: SYSTEM to NULL, size: %zu\n",
> + lbo, lsdc_bo_size(lbo));
> + return 0;
> + }
> +
> + if (old_mem->mem_type == TTM_PL_SYSTEM &&
> + new_mem->mem_type == TTM_PL_TT) {
> + drm_dbg(ddev, "bo[%p] move: SYSTEM to GTT, size: %zu\n",
> + lbo, lsdc_bo_size(lbo));
> + ttm_bo_move_null(tbo, new_mem);
> + return 0;
> + }
> +
> + if (old_mem->mem_type == TTM_PL_TT &&
> + new_mem->mem_type == TTM_PL_SYSTEM) {
> + drm_dbg(ddev, "bo[%p] move: GTT to SYSTEM, size: %zu\n",
> + lbo, lsdc_bo_size(lbo));
> + ttm_resource_free(tbo, &tbo->resource);
> + ttm_bo_assign_mem(tbo, new_mem);
> + return 0;
> + }
> +
> + drm_dbg(ddev, "bo[%p] move: %s to %s, size: %zu\n",
> + lbo,
> + lsdc_mem_type_to_str(old_mem->mem_type),
> + lsdc_mem_type_to_str(new_mem->mem_type),
> + lsdc_bo_size(lbo));
> +
> + return ttm_bo_move_memcpy(tbo, ctx, new_mem);
> +}
> +
> +static int lsdc_bo_reserve_io_mem(struct ttm_device *bdev,
> + struct ttm_resource *mem)
> +{
> + struct lsdc_device *ldev = tdev_to_ldev(bdev);
> +
> + switch (mem->mem_type) {
> + case TTM_PL_SYSTEM:
> + break;
> + case TTM_PL_TT:
> + break;
> + case TTM_PL_VRAM:
> + mem->bus.offset = (mem->start << PAGE_SHIFT) + ldev->vram_base;
> + mem->bus.is_iomem = true;
> + mem->bus.caching = ttm_write_combined;
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static struct ttm_device_funcs lsdc_bo_driver = {
> + .ttm_tt_create = lsdc_ttm_tt_create,
> + .ttm_tt_populate = lsdc_ttm_tt_populate,
> + .ttm_tt_unpopulate = lsdc_ttm_tt_unpopulate,
> + .ttm_tt_destroy = lsdc_ttm_tt_destroy,
> + .eviction_valuable = ttm_bo_eviction_valuable,
> + .evict_flags = lsdc_bo_evict_flags,
> + .move = lsdc_bo_move,
> + .io_mem_reserve = lsdc_bo_reserve_io_mem,
> +};
> +
> +u64 lsdc_bo_gpu_offset(struct lsdc_bo *lbo)
> +{
> + struct ttm_buffer_object *tbo = &lbo->tbo;
> + struct drm_device *ddev = tbo->base.dev;
> + struct ttm_resource *resource = tbo->resource;
> +
> + if (unlikely(!tbo->pin_count)) {
> + drm_err(ddev, "unpinned bo, gpu virtual address is invalid\n");
> + return 0;
> + }
> +
> + if (unlikely(resource->mem_type == TTM_PL_SYSTEM))
> + return 0;
> +
> + return resource->start << PAGE_SHIFT;
> +}
> +
> +size_t lsdc_bo_size(struct lsdc_bo *lbo)
> +{
> + struct ttm_buffer_object *tbo = &lbo->tbo;
> +
> + return tbo->base.size;
> +}
> +
> +int lsdc_bo_reserve(struct lsdc_bo *lbo)
> +{
> + return ttm_bo_reserve(&lbo->tbo, true, false, NULL);
> +}
> +
> +void lsdc_bo_unreserve(struct lsdc_bo *lbo)
> +{
> + return ttm_bo_unreserve(&lbo->tbo);
> +}
> +
> +int lsdc_bo_pin(struct lsdc_bo *lbo, u32 domain, u64 *gpu_addr)
> +{
> + struct ttm_operation_ctx ctx = { false, false };
> + struct ttm_buffer_object *tbo = &lbo->tbo;
> + struct lsdc_device *ldev = tdev_to_ldev(tbo->bdev);
> + int ret;
> +
> + if (tbo->pin_count)
> + goto bo_pinned;
> +
> + if (lbo->sharing_count && domain == LSDC_GEM_DOMAIN_VRAM)
> + return -EINVAL;
> +
> + if (domain)
> + lsdc_bo_set_placement(lbo, domain);
> +
> + ret = ttm_bo_validate(tbo, &lbo->placement, &ctx);
> + if (unlikely(ret)) {
> + drm_err(&ldev->base, "%p validate failed: %d\n", lbo, ret);
> + return ret;
> + }
> +
> + if (domain == LSDC_GEM_DOMAIN_VRAM)
> + ldev->vram_pinned_size += lsdc_bo_size(lbo);
> + else if (domain == LSDC_GEM_DOMAIN_GTT)
> + ldev->gtt_pinned_size += lsdc_bo_size(lbo);
> +
> +bo_pinned:
> + ttm_bo_pin(tbo);
> +
> + if (gpu_addr)
> + *gpu_addr = lsdc_bo_gpu_offset(lbo);
> +
> + return 0;
> +}
> +
> +void lsdc_bo_unpin(struct lsdc_bo *lbo)
> +{
> + struct ttm_buffer_object *tbo = &lbo->tbo;
> + struct lsdc_device *ldev = tdev_to_ldev(tbo->bdev);
> +
> + if (unlikely(!tbo->pin_count)) {
> + drm_dbg(&ldev->base, "%p unpin is not necessary\n", lbo);
> + return;
> + }
> +
> + ttm_bo_unpin(tbo);
> +
> + if (!tbo->pin_count) {
> + if (tbo->resource->mem_type == TTM_PL_VRAM)
> + ldev->vram_pinned_size -= lsdc_bo_size(lbo);
> + else if (tbo->resource->mem_type == TTM_PL_TT)
> + ldev->gtt_pinned_size -= lsdc_bo_size(lbo);
> + }
> +}
> +
> +void lsdc_bo_ref(struct lsdc_bo *lbo)
> +{
> + struct ttm_buffer_object *tbo = &lbo->tbo;
> +
> + ttm_bo_get(tbo);
> +}
> +
> +void lsdc_bo_unref(struct lsdc_bo *lbo)
> +{
> + struct ttm_buffer_object *tbo = &lbo->tbo;
> +
> + ttm_bo_put(tbo);
> +}
> +
> +int lsdc_bo_kmap(struct lsdc_bo *lbo, void **pptr)
> +{
> + struct ttm_buffer_object *tbo = &lbo->tbo;
> + struct drm_gem_object *gem = &tbo->base;
> + struct drm_device *ddev = gem->dev;
> + bool is_iomem;
> + long ret;
> + int err;
> +
> + ret = dma_resv_wait_timeout(gem->resv,
> + DMA_RESV_USAGE_KERNEL,
> + false,
> + MAX_SCHEDULE_TIMEOUT);
> + if (ret < 0) {
> + drm_warn(ddev, "wait fence timeout\n");
> + return ret;
> + }
> +
> + if (lbo->kptr)
> + goto already_kmapped;
> +
> + err = ttm_bo_kmap(tbo, 0, PFN_UP(lsdc_bo_size(lbo)), &lbo->kmap);
> + if (err) {
> + drm_err(ddev, "kmap %p failed: %d\n", lbo, err);
> + return err;
> + }
> +
> + lbo->kptr = ttm_kmap_obj_virtual(&lbo->kmap, &is_iomem);
> +
> +already_kmapped:
> + if (pptr)
> + *pptr = lbo->kptr;
> +
> + return 0;
> +}
> +
> +void lsdc_bo_kunmap(struct lsdc_bo *lbo)
> +{
> + if (!lbo->kptr)
> + return;
> +
> + lbo->kptr = NULL;
> + ttm_bo_kunmap(&lbo->kmap);
> +}
> +
> +int lsdc_bo_evict_vram(struct drm_device *ddev)
> +{
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + struct ttm_device *bdev = &ldev->bdev;
> + struct ttm_resource_manager *man;
> +
> + man = ttm_manager_type(bdev, TTM_PL_VRAM);
> + if (unlikely(!man))
> + return 0;
> +
> + return ttm_resource_manager_evict_all(bdev, man);
> +}
> +
> +static void lsdc_bo_destroy(struct ttm_buffer_object *tbo)
> +{
> + struct lsdc_device *ldev = tdev_to_ldev(tbo->bdev);
> + struct lsdc_bo *lbo = to_lsdc_bo(tbo);
> +
> + mutex_lock(&ldev->gem.mutex);
> + list_del_init(&lbo->list);
> + mutex_unlock(&ldev->gem.mutex);
> +
> + drm_gem_object_release(&tbo->base);
> +
> + kfree(lbo);
> +}
> +
> +struct lsdc_bo *lsdc_bo_create(struct drm_device *ddev,
> + u32 domain,
> + size_t size,
> + bool kernel,
> + struct sg_table *sg,
> + struct dma_resv *resv)
> +{
> + struct lsdc_device *ldev = to_lsdc(ddev);
> + struct ttm_device *bdev = &ldev->bdev;
> + struct ttm_buffer_object *tbo;
> + struct lsdc_bo *lbo;
> + enum ttm_bo_type bo_type;
> + int ret;
> +
> + lbo = kzalloc(sizeof(*lbo), GFP_KERNEL);
> + if (!lbo)
> + return ERR_PTR(-ENOMEM);
> +
> + INIT_LIST_HEAD(&lbo->list);
> +
> + lbo->initial_domain = domain & (LSDC_GEM_DOMAIN_VRAM |
> + LSDC_GEM_DOMAIN_GTT |
> + LSDC_GEM_DOMAIN_SYSTEM);
> +
> + tbo = &lbo->tbo;
> +
> + size = ALIGN(size, PAGE_SIZE);
> +
> + ret = drm_gem_object_init(ddev, &tbo->base, size);
> + if (ret) {
> + kfree(lbo);
> + return ERR_PTR(ret);
> + }
> +
> + tbo->bdev = bdev;
> +
> + if (kernel)
> + bo_type = ttm_bo_type_kernel;
> + else if (sg)
> + bo_type = ttm_bo_type_sg;
> + else
> + bo_type = ttm_bo_type_device;
> +
> + lsdc_bo_set_placement(lbo, domain);
> +
> + ret = ttm_bo_init_validate(bdev,
> + tbo,
> + bo_type,
> + &lbo->placement,
> + 0,
> + false,
> + sg,
> + resv,
> + lsdc_bo_destroy);
> + if (ret) {
> + kfree(lbo);
> + return ERR_PTR(ret);
> + }
> +
> + return lbo;
> +}
> +
> +static void lsdc_ttm_fini(struct drm_device *ddev, void *data)
> +{
> + struct lsdc_device *ldev = (struct lsdc_device *)data;
> +
> + ttm_range_man_fini(&ldev->bdev, TTM_PL_VRAM);
> + ttm_range_man_fini(&ldev->bdev, TTM_PL_TT);
> +
> + ttm_device_fini(&ldev->bdev);
> +
> + drm_dbg(ddev, "ttm finished\n");
> +}
> +
> +int lsdc_ttm_init(struct lsdc_device *ldev)
> +{
> + struct drm_device *ddev = &ldev->base;
> + unsigned long num_vram_pages;
> + unsigned long num_gtt_pages;
> + int ret;
> +
> + ret = ttm_device_init(&ldev->bdev,
> + &lsdc_bo_driver,
> + ddev->dev,
> + ddev->anon_inode->i_mapping,
> + ddev->vma_offset_manager,
> + false,
> + false);
> + if (ret)
> + return ret;
> +
> + num_vram_pages = ldev->vram_size >> PAGE_SHIFT;
> +
> + ret = ttm_range_man_init(&ldev->bdev,
> + TTM_PL_VRAM,
> + false,
> + num_vram_pages);
> + if (unlikely(ret))
> + return ret;
> +
> + drm_info(ddev, "VRAM: %lu pages ready\n", num_vram_pages);
> +
> + /* 512M is far enough for us now */
> + ldev->gtt_size = 512 << 20;
> +
> + num_gtt_pages = ldev->gtt_size >> PAGE_SHIFT;
> +
> + ret = ttm_range_man_init(&ldev->bdev,
> + TTM_PL_TT,
> + true,
> + num_gtt_pages);
> + if (unlikely(ret))
> + return ret;
> +
> + drm_info(ddev, "GTT: %lu pages ready\n", num_gtt_pages);
> +
> + return drmm_add_action_or_reset(ddev, lsdc_ttm_fini, ldev);
> +}
> +
> +void lsdc_ttm_debugfs_init(struct lsdc_device *ldev)
> +{
> + struct ttm_device *bdev = &ldev->bdev;
> + struct drm_device *ddev = &ldev->base;
> + struct drm_minor *minor = ddev->primary;
> + struct dentry *root = minor->debugfs_root;
> + struct ttm_resource_manager *vram_man;
> + struct ttm_resource_manager *gtt_man;
> +
> + vram_man = ttm_manager_type(bdev, TTM_PL_VRAM);
> + gtt_man = ttm_manager_type(bdev, TTM_PL_TT);
> +
> + ttm_resource_manager_create_debugfs(vram_man, root, "vram_mm");
> + ttm_resource_manager_create_debugfs(gtt_man, root, "gtt_mm");
> +}
> diff --git a/drivers/gpu/drm/loongson/lsdc_ttm.h b/drivers/gpu/drm/loongson/lsdc_ttm.h
> new file mode 100644
> index 000000000000..e4ba175c175e
> --- /dev/null
> +++ b/drivers/gpu/drm/loongson/lsdc_ttm.h
> @@ -0,0 +1,88 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (C) 2023 Loongson Corporation
> + */
> +
> +#ifndef __LSDC_TTM_H__
> +#define __LSDC_TTM_H__
> +
> +#include <linux/container_of.h>
> +#include <linux/iosys-map.h>
> +#include <linux/list.h>
> +
> +#include <drm/drm_gem.h>
> +#include <drm/ttm/ttm_bo.h>
> +#include <drm/ttm/ttm_placement.h>
> +#include <drm/ttm/ttm_range_manager.h>
> +#include <drm/ttm/ttm_tt.h>
> +
> +#define LSDC_GEM_DOMAIN_SYSTEM 0x1
> +#define LSDC_GEM_DOMAIN_GTT 0x2
> +#define LSDC_GEM_DOMAIN_VRAM 0x4
> +
> +struct lsdc_bo {
> + struct ttm_buffer_object tbo;
> +
> + /* Protected by gem.mutex */
> + struct list_head list;
> +
> + struct iosys_map map;
> +
> + unsigned int vmap_count;
> + /* cross device driver sharing reference count */
> + unsigned int sharing_count;
> +
> + struct ttm_bo_kmap_obj kmap;
> + void *kptr;
> +
> + u32 initial_domain;
> +
> + struct ttm_placement placement;
> + struct ttm_place placements[4];
> +};
> +
> +static inline struct ttm_buffer_object *to_ttm_bo(struct drm_gem_object *gem)
> +{
> + return container_of(gem, struct ttm_buffer_object, base);
> +}
> +
> +static inline struct lsdc_bo *to_lsdc_bo(struct ttm_buffer_object *tbo)
> +{
> + return container_of(tbo, struct lsdc_bo, tbo);
> +}
> +
> +static inline struct lsdc_bo *gem_to_lsdc_bo(struct drm_gem_object *gem)
> +{
> + return container_of(gem, struct lsdc_bo, tbo.base);
> +}
> +
> +const char *lsdc_mem_type_to_str(uint32_t mem_type);
> +
> +struct lsdc_bo *lsdc_bo_create(struct drm_device *ddev,
> + u32 domain,
> + size_t size,
> + bool kernel,
> + struct sg_table *sg,
> + struct dma_resv *resv);
The same problem as above.
Huacai
> +
> +int lsdc_bo_reserve(struct lsdc_bo *lbo);
> +void lsdc_bo_unreserve(struct lsdc_bo *lbo);
> +
> +int lsdc_bo_pin(struct lsdc_bo *lbo, u32 domain, u64 *gpu_addr);
> +void lsdc_bo_unpin(struct lsdc_bo *lbo);
> +
> +void lsdc_bo_ref(struct lsdc_bo *lbo);
> +void lsdc_bo_unref(struct lsdc_bo *lbo);
> +
> +u64 lsdc_bo_gpu_offset(struct lsdc_bo *lbo);
> +size_t lsdc_bo_size(struct lsdc_bo *lbo);
> +
> +int lsdc_bo_kmap(struct lsdc_bo *lbo, void **pptr);
> +void lsdc_bo_kunmap(struct lsdc_bo *lbo);
> +
> +int lsdc_bo_evict_vram(struct drm_device *ddev);
> +
> +int lsdc_ttm_init(struct lsdc_device *ldev);
> +void lsdc_ttm_debugfs_init(struct lsdc_device *ldev);
> +
> +#endif
> --
> 2.25.1
>
Powered by blists - more mailing lists