| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20230510065253.GA11711@pendragon.ideasonboard.com>
Date: Wed, 10 May 2023 09:52:53 +0300
From: Laurent Pinchart <laurent.pinchart@...asonboard.com>
To: Michal Simek <michal.simek@....com>
Cc: linux-kernel@...r.kernel.org, monstr@...str.eu,
michal.simek@...inx.com, git@...inx.com,
Amit Kumar Mahapatra <amit.kumar-mahapatra@...inx.com>,
Ashok Reddy Soma <ashok.reddy.soma@...inx.com>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Parth Gajjar <parth.gajjar@....com>,
Rob Herring <robh+dt@...nel.org>,
Vishal Sagar <vishal.sagar@....com>,
devicetree@...r.kernel.org, linux-arm-kernel@...ts.infradead.org
Subject: Re: [PATCH 01/23] arm64: zynqmp: Describe TI phy as ethernet-phy-id
Hi Michal,
Thank you for the patch.
On Tue, May 02, 2023 at 03:35:29PM +0200, Michal Simek wrote:
> TI DP83867 is using strapping based on MIO pins. Tristate setup can influce
> PHY address. That's why switch description with ethernet-phy-id compatible
> string which enable calling reset. PHY itself setups phy address after
> power up or reset.
I'm sorry but I don't understand this :-(
> Phy reset is done via gpio.
>
> Signed-off-by: Michal Simek <michal.simek@....com>
> ---
>
> Checkpatch is reporting issue
> warning: DT compatible string "ethernet-phy-id2000.a231" appears un-documented
> but it should be fully aligned with
> Documentation/devicetree/bindings/net/ethernet-phy.yaml
> ---
> .../boot/dts/xilinx/zynqmp-zcu102-revA.dts | 23 +++++++++++------
> .../boot/dts/xilinx/zynqmp-zcu102-revB.dts | 25 +++++++++++--------
> .../boot/dts/xilinx/zynqmp-zcu104-revA.dts | 22 ++++++++++------
> .../boot/dts/xilinx/zynqmp-zcu104-revC.dts | 22 ++++++++++------
> .../boot/dts/xilinx/zynqmp-zcu106-revA.dts | 22 ++++++++++------
> .../boot/dts/xilinx/zynqmp-zcu111-revA.dts | 22 ++++++++++------
> 6 files changed, 90 insertions(+), 46 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
> index 13c43324f1d2..c193579400cf 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
> @@ -2,7 +2,8 @@
> /*
> * dts file for Xilinx ZynqMP ZCU102 RevA
> *
> - * (C) Copyright 2015 - 2021, Xilinx, Inc.
> + * (C) Copyright 2015 - 2022, Xilinx, Inc.
> + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
> *
> * Michal Simek <michal.simek@...inx.com>
> */
> @@ -200,13 +201,19 @@ &gem3 {
> phy-mode = "rgmii-id";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_gem3_default>;
> - phy0: ethernet-phy@21 {
> - reg = <21>;
> - ti,rx-internal-delay = <0x8>;
> - ti,tx-internal-delay = <0xa>;
> - ti,fifo-depth = <0x1>;
> - ti,dp83867-rxctrl-strap-quirk;
> - /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
> + mdio: mdio {
The "mdio" label isn't needed. Same below.
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy@21 {
> + #phy-cells = <1>;
> + compatible = "ethernet-phy-id2000.a231";
> + reg = <21>;
> + ti,rx-internal-delay = <0x8>;
> + ti,tx-internal-delay = <0xa>;
> + ti,fifo-depth = <0x1>;
> + ti,dp83867-rxctrl-strap-quirk;
> + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
> + };
> };
> };
>
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
> index f7d718ff116b..00b930f20718 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revB.dts
> @@ -2,7 +2,8 @@
> /*
> * dts file for Xilinx ZynqMP ZCU102 RevB
> *
> - * (C) Copyright 2016 - 2021, Xilinx, Inc.
> + * (C) Copyright 2016 - 2022, Xilinx, Inc.
> + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
> *
> * Michal Simek <michal.simek@...inx.com>
> */
> @@ -16,16 +17,20 @@ / {
>
> &gem3 {
> phy-handle = <&phyc>;
> - phyc: ethernet-phy@c {
> - reg = <0xc>;
> - ti,rx-internal-delay = <0x8>;
> - ti,tx-internal-delay = <0xa>;
> - ti,fifo-depth = <0x1>;
> - ti,dp83867-rxctrl-strap-quirk;
> - /* reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>; */
> + mdio: mdio {
> + phyc: ethernet-phy@c {
> + #phy-cells = <0x1>;
> + compatible = "ethernet-phy-id2000.a231";
> + reg = <0xc>;
> + ti,rx-internal-delay = <0x8>;
> + ti,tx-internal-delay = <0xa>;
> + ti,fifo-depth = <0x1>;
> + ti,dp83867-rxctrl-strap-quirk;
> + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
> + };
> + /* Cleanup from RevA */
> + /delete-node/ ethernet-phy@21;
> };
> - /* Cleanup from RevA */
> - /delete-node/ ethernet-phy@21;
> };
>
> /* Fix collision with u61 */
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
> index 485585c491f4..11c1eaef9f53 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts
> @@ -2,7 +2,8 @@
> /*
> * dts file for Xilinx ZynqMP ZCU104
> *
> - * (C) Copyright 2017 - 2021, Xilinx, Inc.
> + * (C) Copyright 2017 - 2022, Xilinx, Inc.
> + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
> *
> * Michal Simek <michal.simek@...inx.com>
> */
> @@ -109,12 +110,19 @@ &gem3 {
> phy-mode = "rgmii-id";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_gem3_default>;
> - phy0: ethernet-phy@c {
> - reg = <0xc>;
> - ti,rx-internal-delay = <0x8>;
> - ti,tx-internal-delay = <0xa>;
> - ti,fifo-depth = <0x1>;
> - ti,dp83867-rxctrl-strap-quirk;
> + mdio: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy@c {
> + #phy-cells = <1>;
> + compatible = "ethernet-phy-id2000.a231";
> + reg = <0xc>;
> + ti,rx-internal-delay = <0x8>;
> + ti,tx-internal-delay = <0xa>;
> + ti,fifo-depth = <0x1>;
> + ti,dp83867-rxctrl-strap-quirk;
> + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
> + };
> };
> };
>
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
> index 44ec9edd2452..c06c138fa3e5 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
> @@ -2,7 +2,8 @@
> /*
> * dts file for Xilinx ZynqMP ZCU104
> *
> - * (C) Copyright 2017 - 2021, Xilinx, Inc.
> + * (C) Copyright 2017 - 2022, Xilinx, Inc.
> + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
> *
> * Michal Simek <michal.simek@...inx.com>
> */
> @@ -114,12 +115,19 @@ &gem3 {
> phy-mode = "rgmii-id";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_gem3_default>;
> - phy0: ethernet-phy@c {
> - reg = <0xc>;
> - ti,rx-internal-delay = <0x8>;
> - ti,tx-internal-delay = <0xa>;
> - ti,fifo-depth = <0x1>;
> - ti,dp83867-rxctrl-strap-quirk;
> + mdio: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy@c {
> + #phy-cells = <1>;
> + compatible = "ethernet-phy-id2000.a231";
> + reg = <0xc>;
> + ti,rx-internal-delay = <0x8>;
> + ti,tx-internal-delay = <0xa>;
> + ti,fifo-depth = <0x1>;
> + ti,dp83867-rxctrl-strap-quirk;
> + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
> + };
> };
> };
>
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
> index 09773b7200f8..52cdec33f190 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
> @@ -2,7 +2,8 @@
> /*
> * dts file for Xilinx ZynqMP ZCU106
> *
> - * (C) Copyright 2016 - 2021, Xilinx, Inc.
> + * (C) Copyright 2016 - 2022, Xilinx, Inc.
> + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
> *
> * Michal Simek <michal.simek@...inx.com>
> */
> @@ -212,12 +213,19 @@ &gem3 {
> phy-mode = "rgmii-id";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_gem3_default>;
> - phy0: ethernet-phy@c {
> - reg = <0xc>;
> - ti,rx-internal-delay = <0x8>;
> - ti,tx-internal-delay = <0xa>;
> - ti,fifo-depth = <0x1>;
> - ti,dp83867-rxctrl-strap-quirk;
> + mdio: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy@c {
> + #phy-cells = <1>;
> + reg = <0xc>;
> + compatible = "ethernet-phy-id2000.a231";
> + ti,rx-internal-delay = <0x8>;
> + ti,tx-internal-delay = <0xa>;
> + ti,fifo-depth = <0x1>;
> + ti,dp83867-rxctrl-strap-quirk;
> + reset-gpios = <&tca6416_u97 6 GPIO_ACTIVE_LOW>;
> + };
> };
> };
>
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
> index e0305dcbb010..699cc9ce7898 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
> @@ -2,7 +2,8 @@
> /*
> * dts file for Xilinx ZynqMP ZCU111
> *
> - * (C) Copyright 2017 - 2021, Xilinx, Inc.
> + * (C) Copyright 2017 - 2022, Xilinx, Inc.
> + * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
> *
> * Michal Simek <michal.simek@...inx.com>
> */
> @@ -172,12 +173,19 @@ &gem3 {
> phy-mode = "rgmii-id";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_gem3_default>;
> - phy0: ethernet-phy@c {
> - reg = <0xc>;
> - ti,rx-internal-delay = <0x8>;
> - ti,tx-internal-delay = <0xa>;
> - ti,fifo-depth = <0x1>;
> - ti,dp83867-rxctrl-strap-quirk;
> + mdio: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy@c {
> + #phy-cells = <1>;
> + compatible = "ethernet-phy-id2000.a231";
> + reg = <0xc>;
> + ti,rx-internal-delay = <0x8>;
> + ti,tx-internal-delay = <0xa>;
> + ti,fifo-depth = <0x1>;
> + ti,dp83867-rxctrl-strap-quirk;
> + reset-gpios = <&tca6416_u22 6 GPIO_ACTIVE_LOW>;
> + };
> };
> };
>
--
Regards,
Laurent Pinchart
Powered by blists - more mailing lists