[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20230516110038.2413224-38-schnelle@linux.ibm.com>
Date: Tue, 16 May 2023 13:00:33 +0200
From: Niklas Schnelle <schnelle@...ux.ibm.com>
To: Arnd Bergmann <arnd@...db.de>, Helge Deller <deller@....de>
Cc: Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Bjorn Helgaas <bhelgaas@...gle.com>,
Uwe Kleine-König
<u.kleine-koenig@...gutronix.de>,
Mauro Carvalho Chehab <mchehab@...nel.org>,
Alan Stern <stern@...land.harvard.edu>,
"Rafael J. Wysocki" <rafael@...nel.org>,
Geert Uytterhoeven <geert@...ux-m68k.org>,
Paul Walmsley <paul.walmsley@...ive.com>,
Palmer Dabbelt <palmer@...belt.com>,
Albert Ou <aou@...s.berkeley.edu>,
linux-kernel@...r.kernel.org, linux-arch@...r.kernel.org,
linux-pci@...r.kernel.org,
Ville Syrjälä
<ville.syrjala@...ux.intel.com>, linux-fbdev@...r.kernel.org,
dri-devel@...ts.freedesktop.org
Subject: [PATCH v4 37/41] fbdev: atyfb: Remove unused clock determination
Just below the removed lines par->clk_wr_offset is hard coded to 3 so
there is no use in determining a different clock just to then ignore it
anyway. This also removes the only I/O port use remaining in the driver
allowing it to be built without CONFIG_HAS_IOPORT.
Link: https://lore.kernel.org/all/ZBx5aLo5h546BzBt@intel.com/
Suggested-by: Ville Syrjälä <ville.syrjala@...ux.intel.com>
Signed-off-by: Niklas Schnelle <schnelle@...ux.ibm.com>
---
Note: The HAS_IOPORT Kconfig option was added in v6.4-rc1 so
per-subsystem patches may be applied independently
drivers/video/fbdev/aty/atyfb_base.c | 5 -----
1 file changed, 5 deletions(-)
diff --git a/drivers/video/fbdev/aty/atyfb_base.c b/drivers/video/fbdev/aty/atyfb_base.c
index b02e4e645035..cba2b113b28b 100644
--- a/drivers/video/fbdev/aty/atyfb_base.c
+++ b/drivers/video/fbdev/aty/atyfb_base.c
@@ -3498,11 +3498,6 @@ static int atyfb_setup_generic(struct pci_dev *pdev, struct fb_info *info,
if (ret)
goto atyfb_setup_generic_fail;
#endif
- if (!(aty_ld_le32(CRTC_GEN_CNTL, par) & CRTC_EXT_DISP_EN))
- par->clk_wr_offset = (inb(R_GENMO) & 0x0CU) >> 2;
- else
- par->clk_wr_offset = aty_ld_8(CLOCK_CNTL, par) & 0x03U;
-
/* according to ATI, we should use clock 3 for acelerated mode */
par->clk_wr_offset = 3;
--
2.39.2
Powered by blists - more mailing lists