lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [thread-next>] [day] [month] [year] [list]
Message-ID: <20230609083009.2822259-1-wenst@chromium.org>
Date:   Fri,  9 Jun 2023 16:29:57 +0800
From:   Chen-Yu Tsai <wenst@...omium.org>
To:     Rob Herring <robh+dt@...nel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
        Conor Dooley <conor+dt@...nel.org>,
        Mark Brown <broonie@...nel.org>,
        Liam Girdwood <lgirdwood@...il.com>,
        Matthias Brugger <matthias.bgg@...il.com>,
        AngeloGioacchino Del Regno 
        <angelogioacchino.delregno@...labora.com>
Cc:     Chen-Yu Tsai <wenst@...omium.org>, devicetree@...r.kernel.org,
        linux-arm-kernel@...ts.infradead.org,
        linux-mediatek@...ts.infradead.org, linux-kernel@...r.kernel.org
Subject: [PATCH 0/9] regulator: mt6358: Remove bogus regulators and improvements

Hi,

This series is a cleanup and improvement of the MT6358 regulator driver.
Various discrepancies were found while preparing to upstream MT8186
device trees, which utilize the MT6366 PMIC, that is also covered by
this driver.

Patches 1~8 should go through the regulator tree, and patch 9 through
the soc tree. This series (patches 7 and 8) depends on "regulator: Use
bitfield values for range selectors" [1] I sent out earlier.

This series can be seen as three parts: 

Part 1 - Fixing bogus regulators (patches 1~4 and 9)

There are some regulators listed in the bindings and driver that have no
corresponding pin on the actual hardware. MediaTek says these are a
hardware construct for shared control of the same regulator in the
VCN33 case and an alternative control scheme for low power suspend.

In the VCN33 case, there's only one actual regulator, so we merge the
two and rename them to match the hardware pin. No existing devices use
these AFAICT, so this should be safe to change.

In the *_SSHUB case, the two extra regulators refer to alternative
configuration registers of the same regulators. They are intended for
the SoC's low power mode companion processor to use, not the main
processor or OS. It should be left to the implementation to choose
which set of registers to actually control.

Part 2 - Code cleanup (patches 5 and 6)

Various tables in the regulator driver were not constant, even though
they are just lookup tables. With some reworking of the code, they are
made constant.

Also, some regulators that have a single linear range were using linear
range helpers. This is more complicated than just declaring the range
and step directly in the description. This is simplified to use the
latter approach.

Part 3 - Output voltage fine tuning support (patches 7 and 8)

Many of the LDOs on these PMIC support an extra level of output voltage
fine tuning. Most default to no offset, but a couple have a non-zero
offset by default. Previously this was unaccounted for in the driver and
device tree constraints. On the outputs with non-zero offset, this ends
up becoming a discrepancy between the device tree and actual hardware.
These two patches adds support for this second level of tuning, modeled
as bunch of linear ranges. While it's unlikely we need this level of
control, it's nice to be able to read back the accurate hardware
settings.

Please have a look. After this series is done I'll send out patches for
the MT6366 PMIC, which is what started this. That will also include
updated YAML bindings for MT6366. I think we can merge MT6358 bindings
into them afterwards.

Thanks
ChenYu

[1] https://lore.kernel.org/linux-arm-kernel/20230609075032.2804554-1-wenst@chromium.org/

Chen-Yu Tsai (9):
  regulator: dt-bindings: mt6358: Merge ldo_vcn33_* regulators
  regulator: dt-bindings: mt6358: Drop *_sshub regulators
  regulator: mt6358: Merge VCN33_* regulators
  regulator: mt6358: Drop *_SSHUB regulators
  regulator: mt6358: Const-ify mt6358_regulator_info data structures
  regulator: mt6358: Use linear voltage helpers for single range
    regulators
  regulator: mt6358: Add output voltage fine tuning to fixed regulators
  regulator: mt6358: Add output voltage fine tuning to variable LDOs
  arm64: dts: mediatek: mt6358: Merge ldo_vcn33_* regulators

 .../bindings/regulator/mt6358-regulator.txt   |  34 +-
 arch/arm64/boot/dts/mediatek/mt6358.dtsi      |  11 +-
 drivers/regulator/mt6358-regulator.c          | 499 ++++++++----------
 include/linux/regulator/mt6358-regulator.h    |  10 +-
 4 files changed, 234 insertions(+), 320 deletions(-)

-- 
2.41.0.162.gfafddb0af9-goog

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ