Message-ID: <648ded2a.df0a0220.b78de.4603@mx.google.com>
Date:   Fri, 16 Jun 2023 23:27:59 +0200
From:   Christian Marangi <ansuelsmth@...il.com>
To:     Kalle Valo <kvalo@...nel.org>
Cc:     "David S. Miller" <davem@...emloft.net>,
        Eric Dumazet <edumazet@...gle.com>,
        Jakub Kicinski <kuba@...nel.org>,
        Paolo Abeni <pabeni@...hat.com>, linux-kernel@...r.kernel.org,
        ath10k@...ts.infradead.org, linux-wireless@...r.kernel.org,
        netdev@...r.kernel.org,
        Sebastian Gottschall <s.gottschall@...wrt.com>,
        Steve deRosier <derosier@...-sierra.com>,
        Stefan Lippers-Hollmann <s.l-h@....de>
Subject: Re: [PATCH v14] ath10k: add LED and GPIO controlling support for
 various chipsets

On Fri, Jun 16, 2023 at 01:35:04PM +0200, Christian Marangi wrote:
> On Fri, Jun 16, 2023 at 08:03:23PM +0300, Kalle Valo wrote:
> > Christian Marangi <ansuelsmth@...il.com> writes:
> > 
> > > From: Sebastian Gottschall <s.gottschall@...wrt.com>
> > >
> > > Adds LED and GPIO Control support for 988x, 9887, 9888, 99x0, 9984
> > > based chipsets with on chipset connected led's using WMI Firmware API.
> > > The LED device will get available named as "ath10k-phyX" at sysfs and
> > > can be controlled with various triggers.
> > > Adds also debugfs interface for gpio control.
> > >
> > > Signed-off-by: Sebastian Gottschall <s.gottschall@...wrt.com>
> > > Reviewed-by: Steve deRosier <derosier@...-sierra.com>
> > > [kvalo: major reorg and cleanup]
> > > Signed-off-by: Kalle Valo <kvalo@...eaurora.org>
> > > [ansuel: rebase and small cleanup]
> > > Signed-off-by: Christian Marangi <ansuelsmth@...il.com>
> > > Tested-by: Stefan Lippers-Hollmann <s.l-h@....de>
> > > ---
> > >
> > > Hi,
> > > this is a very old patch from 2018 that somehow was talked till 2020
> > > with Kavlo asked to rebase and resubmit and nobody did.
> > > So here we are in 2023 with me trying to finally have this upstream.
> > >
> > > A summarize of the situation.
> > > - The patch is from years in OpenWRT. Used by anything that has ath10k
> > >   card and a LED connected.
> > > - This patch is also used by the fw variant from Candela Tech with no
> > >   problem reported.
> > > - It was pointed out that this caused some problem with ipq4019 SoC
> > >   but the problem was actually caused by a different bug related to
> > >   interrupts.
> > >
> > > I honestly hope we can have this feature merged since it's really
> > > funny to have something that was so near merge and jet still not
> > > present and with devices not supporting this simple but useful
> > > feature.
> > 
> > Indeed, we should finally get this in. Thanks for working on it.
> > 
> > I did some minor changes to the patch, they are in my pending branch:
> > 
> > https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git/commit/?h=pending&id=686464864538158f22842dc49eddea6fa50e59c1
> > 
> > My comments below, please review my changes. No need to resend because
> > of these.
> >
> 
> Hi,
> very happy this is going further.
> 
> > > --- a/drivers/net/wireless/ath/ath10k/Kconfig
> > > +++ b/drivers/net/wireless/ath/ath10k/Kconfig
> > > @@ -67,6 +67,23 @@ config ATH10K_DEBUGFS
> > >  
> > >  	  If unsure, say Y to make it easier to debug problems.
> > >  
> > > +config ATH10K_LEDS
> > > +	bool "Atheros ath10k LED support"
> > > +	depends on ATH10K
> > > +	select MAC80211_LEDS
> > > +	select LEDS_CLASS
> > > +	select NEW_LEDS
> > > +	default y
> > > +	help
> > > +	  This option enables LEDs support for chipset LED pins.
> > > +	  Each pin is connected via GPIO and can be controlled using
> > > +	  WMI Firmware API.
> > > +
> > > +	  The LED device will get available named as "ath10k-phyX" at sysfs and
> > > +    	  can be controlled with various triggers.
> > > +
> > > +	  Say Y, if you have LED pins connected to the ath10k wireless card.
> > 
> > I'm not sure anymore if we should ask anything from the user, better to
> > enable automatically if LED support is enabled in the kernel. So I
> > simplified this to:
> > 
> > config ATH10K_LEDS
> > 	bool
> > 	depends on ATH10K
> > 	depends on LEDS_CLASS=y || LEDS_CLASS=MAC80211
> > 	default y
> > 
> > This follows what mt76 does:
> > 
> > config MT76_LEDS
> > 	bool
> > 	depends on MT76_CORE
> > 	depends on LEDS_CLASS=y || MT76_CORE=LEDS_CLASS
> > 	default y
> > 
> 
> I remember there was the same discussion in a previous series. OK for me
> for making this by default, only concern is any buildbot error (if any)
> 
> Anyway OK for the change.
> 
> > > @@ -65,6 +66,7 @@ static const struct ath10k_hw_params ath10k_hw_params_list[] = {
> > >  		.dev_id = QCA988X_2_0_DEVICE_ID,
> > >  		.bus = ATH10K_BUS_PCI,
> > >  		.name = "qca988x hw2.0",
> > > +		.led_pin = 1,
> > >  		.patch_load_addr = QCA988X_HW_2_0_PATCH_LOAD_ADDR,
> > >  		.uart_pin = 7,
> > >  		.cc_wraparound_type = ATH10K_HW_CC_WRAP_SHIFTED_ALL,
> > 
> > I prefer following the field order from struct ath10k_hw_params
> > declaration and also setting fields explicitly to zero (even though
> > there are gaps still) so I changed that for every entry.
> > 
> 
> Thanks for the change, np for me.
> 
> > > +int ath10k_leds_register(struct ath10k *ar)
> > > +{
> > > +	int ret;
> > > +
> > > +	if (ar->hw_params.led_pin == 0)
> > > +		/* leds not supported */
> > > +		return 0;
> > > +
> > > +	snprintf(ar->leds.label, sizeof(ar->leds.label), "ath10k-%s",
> > > +		 wiphy_name(ar->hw->wiphy));
> > > +	ar->leds.wifi_led.active_low = 1;
> > > +	ar->leds.wifi_led.gpio = ar->hw_params.led_pin;
> > > +	ar->leds.wifi_led.name = ar->leds.label;
> > > +	ar->leds.wifi_led.default_state = LEDS_GPIO_DEFSTATE_KEEP;
> > > +
> > > +	ar->leds.cdev.name = ar->leds.label;
> > > +	ar->leds.cdev.brightness_set_blocking = ath10k_leds_set_brightness_blocking;
> > > +
> > > +	/* FIXME: this assignment doesn't make sense as it's NULL, remove it? */
> > > +	ar->leds.cdev.default_trigger = ar->leds.wifi_led.default_trigger;
> > 
> > But what to do with this FIXME?
> >
> 
> It was pushed by you in v13.
> 
> I could be wrong but your idea was to prepare for future support of
> other patch that would set the default_trigger to the mac80211 tpt.
> 
> We might got both confused by default_trigger and default_state.
> default_trigger is actually never set and is NULL (actually it's 0)
> 
> We have other 2 patch that adds tpt rates for the mac80211 LED trigger
> and set this trigger as the default one but honestly I would chose a
> different implementation than hardcoding everything.
> 
> If it's ok for you, I would drop the comment and the default_trigger and
> I will send a follow-up patch to this adding DT support by using
> led_classdev_register_ext and defining init_data.
> (and this indirectly would permit better LED naming and defining of
> default-trigger in DT)
> 
> Also ideally I will also send a patch for default_state following
> standard LED implementation. (to set default_state in DT)
> 
> I would prefer this approach as the LED patch already took way too much
> time and I think it's better to merge this initial version and then
> improve it.

If you want to check out I attached the 2 patch (one dt-bindings and the
one for the code) that I will submit when this will be merged (the
change is with the assumption that the FIXME line is dropped)

Tested and works correctly with my use case of wifi card attached with
pcie. This implementation permits to declare the default trigger in DT
instead of hardcoding.

-- 
	Ansuel

View attachment "0001-dt-bindings-net-wireless-qcom-ath10k-Document-LED-no.patch" of type "text/x-diff" (2280 bytes)

View attachment "0002-wifi-ath10k-start-LED-with-the-previous-defined-cdev.patch" of type "text/x-diff" (1664 bytes)

View attachment "0003-wifi-ath10k-add-DT-support-for-LED-definition.patch" of type "text/x-diff" (2589 bytes)

Powered by blists - more mailing lists