| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <552c49b9-8c5b-1776-a564-2ce4ee9aff28@ti.com>
Date: Wed, 19 Jul 2023 15:02:49 +0530
From: Ravi Gunasekaran <r-gunasekaran@...com>
To: Siddharth Vadapalli <s-vadapalli@...com>, <nm@...com>,
<vigneshr@...com>, <kristo@...nel.org>, <robh+dt@...nel.org>,
<krzysztof.kozlowski+dt@...aro.org>, <conor+dt@...nel.org>,
<afd@...com>
CC: <devicetree@...r.kernel.org>, <linux-kernel@...r.kernel.org>,
<linux-arm-kernel@...ts.infradead.org>, <srk@...com>,
Ravi Gunasekaran <r-gunasekaran@...com>
Subject: Re: [PATCH v2] arm64: dts: ti: k3-j721e: Add overlay to enable CPSW9G
ports with GESI
On 7/10/23 1:25 PM, Siddharth Vadapalli wrote:
> The J7 GESI EXP board for J721E Common-Proc-Board supports RGMII mode.
> Use the overlay to configure CPSW9G ports in RGMII-RXID mode.
>
> Add aliases for CPSW9G ports to enable kernel to fetch MAC addresses
> directly from U-Boot.
>
> Signed-off-by: Siddharth Vadapalli <s-vadapalli@...com>
> ---
> v1:
> https://lore.kernel.org/r/20230529094222.512675-1-s-vadapalli@ti.com/
> Changes since v1:
> - Rebase on linux-next tagged next-20230710.
>
> arch/arm64/boot/dts/ti/Makefile | 2 +
> .../dts/ti/k3-j721e-evm-gesi-exp-board.dtso | 196 ++++++++++++++++++
> 2 files changed, 198 insertions(+)
> create mode 100644 arch/arm64/boot/dts/ti/k3-j721e-evm-gesi-exp-board.dtso
>
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index 6dd7b6f1d6ab..01d58aa8b06e 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -46,6 +46,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-evm.dtb
> k3-j721e-evm-dtbs := k3-j721e-common-proc-board.dtb k3-j721e-evm-quad-port-eth-exp.dtbo
> dtb-$(CONFIG_ARCH_K3) += k3-j721e-beagleboneai64.dtb
> dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm.dtb
> +dtb-$(CONFIG_ARCH_K3) += k3-j721e-evm-gesi-exp-board.dtbo
> dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb
>
> # Boards with J721s2 SoC
> @@ -58,3 +59,4 @@ dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
>
> # Enable support for device-tree overlays
> DTC_FLAGS_k3-am6548-iot2050-advanced-m2 += -@
> +DTC_FLAGS_k3-j721e-common-proc-board += -@
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-evm-gesi-exp-board.dtso b/arch/arm64/boot/dts/ti/k3-j721e-evm-gesi-exp-board.dtso
> new file mode 100644
> index 000000000000..5a8e074a924b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-evm-gesi-exp-board.dtso
> @@ -0,0 +1,196 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/**
> + * DT Overlay for CPSW9G in RGMII mode using J7 GESI EXP BRD board with
> + * J721E board.
> + *
> + * GESI Board Product Link: https://www.ti.com/tool/J7EXPCXEVM
> + *
> + * Copyright (C) 2023 Texas Instruments Incorporated - https://www.ti.com/
> + */
> +
> +/dts-v1/;
> +/plugin/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/net/ti-dp83867.h>
> +
> +#include "k3-pinctrl.h"
> +
> +&{/} {
> + aliases {
> + ethernet1 = "/bus@...000/ethernet@...0000/ethernet-ports/port@1";
> + ethernet2 = "/bus@...000/ethernet@...0000/ethernet-ports/port@2";
> + ethernet3 = "/bus@...000/ethernet@...0000/ethernet-ports/port@3";
> + ethernet4 = "/bus@...000/ethernet@...0000/ethernet-ports/port@4";
> + };
> +};
> +
> +&cpsw0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmii1_pins_default
> + &rgmii2_pins_default
> + &rgmii3_pins_default
> + &rgmii4_pins_default>;
> +};
> +
> +&cpsw0_port1 {
> + status = "okay";
> + phy-handle = <&cpsw9g_phy12>;
> + phy-mode = "rgmii-rxid";
> + mac-address = [00 00 00 00 00 00];
> + phys = <&cpsw0_phy_gmii_sel 1>;
> +};
> +
> +&cpsw0_port2 {
> + status = "okay";
> + phy-handle = <&cpsw9g_phy15>;
> + phy-mode = "rgmii-rxid";
> + mac-address = [00 00 00 00 00 00];
> + phys = <&cpsw0_phy_gmii_sel 2>;
> +};
> +
> +&cpsw0_port3 {
> + status = "okay";
> + phy-handle = <&cpsw9g_phy0>;
> + phy-mode = "rgmii-rxid";
> + mac-address = [00 00 00 00 00 00];
> + phys = <&cpsw0_phy_gmii_sel 3>;
> +};
> +
> +&cpsw0_port4 {
> + status = "okay";
> + phy-handle = <&cpsw9g_phy3>;
> + phy-mode = "rgmii-rxid";
> + mac-address = [00 00 00 00 00 00];
> + phys = <&cpsw0_phy_gmii_sel 4>;
> +};
> +
> +&cpsw9g_mdio {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&mdio0_pins_default>;
> + bus_freq = <1000000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpsw9g_phy0: ethernet-phy@0 {
> + reg = <0>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + ti,min-output-impedance;
> + };
> + cpsw9g_phy3: ethernet-phy@3 {
> + reg = <3>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + ti,min-output-impedance;
> + };
> + cpsw9g_phy12: ethernet-phy@12 {
> + reg = <12>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + ti,min-output-impedance;
> + };
> + cpsw9g_phy15: ethernet-phy@15 {
> + reg = <15>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + ti,min-output-impedance;
> + };
> +};
> +
> +&exp1 {
> + p15-hog {
> + /* P15 - EXP_MUX2 */
> + gpio-hog;
> + gpios = <13 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "EXP_MUX2";
> + };
> +
> + p16-hog {
> + /* P16 - EXP_MUX3 */
> + gpio-hog;
> + gpios = <14 GPIO_ACTIVE_HIGH>;
> + output-high;
> + line-name = "EXP_MUX3";
> + };
> +};
> +
> +&main_pmx0 {
> + mdio0_pins_default: mdio0-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x1bc, PIN_OUTPUT, 0) /* (V24) MDIO0_MDC */
> + J721E_IOPAD(0x1b8, PIN_INPUT, 0) /* (V26) MDIO0_MDIO */
> + >;
> + };
> +
> + rgmii1_pins_default: rgmii1-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x4, PIN_INPUT, 4) /* (AC23) PRG1_PRU0_GPO0.RGMII1_RD0 */
> + J721E_IOPAD(0x8, PIN_INPUT, 4) /* (AG22) PRG1_PRU0_GPO1.RGMII1_RD1 */
> + J721E_IOPAD(0xc, PIN_INPUT, 4) /* (AF22) PRG1_PRU0_GPO2.RGMII1_RD2 */
> + J721E_IOPAD(0x10, PIN_INPUT, 4) /* (AJ23) PRG1_PRU0_GPO3.RGMII1_RD3 */
> + J721E_IOPAD(0x1c, PIN_INPUT, 4) /* (AD22) PRG1_PRU0_GPO6.RGMII1_RXC */
> + J721E_IOPAD(0x14, PIN_INPUT, 4) /* (AH23) PRG1_PRU0_GPO4.RGMII1_RX_CTL */
> + J721E_IOPAD(0x30, PIN_OUTPUT, 4) /* (AF24) PRG1_PRU0_GPO11.RGMII1_TD0 */
> + J721E_IOPAD(0x34, PIN_OUTPUT, 4) /* (AJ24) PRG1_PRU0_GPO12.RGMII1_TD1 */
> + J721E_IOPAD(0x38, PIN_OUTPUT, 4) /* (AG24) PRG1_PRU0_GPO13.RGMII1_TD2 */
> + J721E_IOPAD(0x3c, PIN_OUTPUT, 4) /* (AD24) PRG1_PRU0_GPO14.RGMII1_TD3 */
> + J721E_IOPAD(0x44, PIN_OUTPUT, 4) /* (AE24) PRG1_PRU0_GPO16.RGMII1_TXC */
> + J721E_IOPAD(0x40, PIN_OUTPUT, 4) /* (AC24) PRG1_PRU0_GPO15.RGMII1_TX_CTL */
> + >;
> + };
> +
> + rgmii2_pins_default: rgmii2-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x58, PIN_INPUT, 4) /* (AE22) PRG1_PRU1_GPO0.RGMII2_RD0 */
> + J721E_IOPAD(0x5c, PIN_INPUT, 4) /* (AG23) PRG1_PRU1_GPO1.RGMII2_RD1 */
> + J721E_IOPAD(0x60, PIN_INPUT, 4) /* (AF23) PRG1_PRU1_GPO2.RGMII2_RD2 */
> + J721E_IOPAD(0x64, PIN_INPUT, 4) /* (AD23) PRG1_PRU1_GPO3.RGMII2_RD3 */
> + J721E_IOPAD(0x70, PIN_INPUT, 4) /* (AE23) PRG1_PRU1_GPO6.RGMII2_RXC */
> + J721E_IOPAD(0x68, PIN_INPUT, 4) /* (AH24) PRG1_PRU1_GPO4.RGMII2_RX_CTL */
> + J721E_IOPAD(0x84, PIN_OUTPUT, 4) /* (AJ25) PRG1_PRU1_GPO11.RGMII2_TD0 */
> + J721E_IOPAD(0x88, PIN_OUTPUT, 4) /* (AH25) PRG1_PRU1_GPO12.RGMII2_TD1 */
> + J721E_IOPAD(0x8c, PIN_OUTPUT, 4) /* (AG25) PRG1_PRU1_GPO13.RGMII2_TD2 */
> + J721E_IOPAD(0x90, PIN_OUTPUT, 4) /* (AH26) PRG1_PRU1_GPO14.RGMII2_TD3 */
> + J721E_IOPAD(0x98, PIN_OUTPUT, 4) /* (AJ26) PRG1_PRU1_GPO16.RGMII2_TXC */
> + J721E_IOPAD(0x94, PIN_OUTPUT, 4) /* (AJ27) PRG1_PRU1_GPO15.RGMII2_TX_CTL */
> + >;
> + };
> +
> + rgmii3_pins_default: rgmii3-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0xb0, PIN_INPUT, 4) /* (AF28) PRG0_PRU0_GPO0.RGMII3_RD0 */
> + J721E_IOPAD(0xb4, PIN_INPUT, 4) /* (AE28) PRG0_PRU0_GPO1.RGMII3_RD1 */
> + J721E_IOPAD(0xb8, PIN_INPUT, 4) /* (AE27) PRG0_PRU0_GPO2.RGMII3_RD2 */
> + J721E_IOPAD(0xbc, PIN_INPUT, 4) /* (AD26) PRG0_PRU0_GPO3.RGMII3_RD3 */
> + J721E_IOPAD(0xc8, PIN_INPUT, 4) /* (AE26) PRG0_PRU0_GPO6.RGMII3_RXC */
> + J721E_IOPAD(0xc0, PIN_INPUT, 4) /* (AD25) PRG0_PRU0_GPO4.RGMII3_RX_CTL */
> + J721E_IOPAD(0xdc, PIN_OUTPUT, 4) /* (AJ28) PRG0_PRU0_GPO11.RGMII3_TD0 */
> + J721E_IOPAD(0xe0, PIN_OUTPUT, 4) /* (AH27) PRG0_PRU0_GPO12.RGMII3_TD1 */
> + J721E_IOPAD(0xe4, PIN_OUTPUT, 4) /* (AH29) PRG0_PRU0_GPO13.RGMII3_TD2 */
> + J721E_IOPAD(0xe8, PIN_OUTPUT, 4) /* (AG28) PRG0_PRU0_GPO14.RGMII3_TD3 */
> + J721E_IOPAD(0xf0, PIN_OUTPUT, 4) /* (AH28) PRG0_PRU0_GPO16.RGMII3_TXC */
> + J721E_IOPAD(0xec, PIN_OUTPUT, 4) /* (AG27) PRG0_PRU0_GPO15.RGMII3_TX_CTL */
> + >;
> + };
> +
> + rgmii4_pins_default: rgmii4-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x100, PIN_INPUT, 4) /* (AE29) PRG0_PRU1_GPO0.RGMII4_RD0 */
> + J721E_IOPAD(0x104, PIN_INPUT, 4) /* (AD28) PRG0_PRU1_GPO1.RGMII4_RD1 */
> + J721E_IOPAD(0x108, PIN_INPUT, 4) /* (AD27) PRG0_PRU1_GPO2.RGMII4_RD2 */
> + J721E_IOPAD(0x10c, PIN_INPUT, 4) /* (AC25) PRG0_PRU1_GPO3.RGMII4_RD3 */
> + J721E_IOPAD(0x118, PIN_INPUT, 4) /* (AC26) PRG0_PRU1_GPO6.RGMII4_RXC */
> + J721E_IOPAD(0x110, PIN_INPUT, 4) /* (AD29) PRG0_PRU1_GPO4.RGMII4_RX_CTL */
> + J721E_IOPAD(0x12c, PIN_OUTPUT, 4) /* (AG26) PRG0_PRU1_GPO11.RGMII4_TD0 */
> + J721E_IOPAD(0x130, PIN_OUTPUT, 4) /* (AF27) PRG0_PRU1_GPO12.RGMII4_TD1 */
> + J721E_IOPAD(0x134, PIN_OUTPUT, 4) /* (AF26) PRG0_PRU1_GPO13.RGMII4_TD2 */
> + J721E_IOPAD(0x138, PIN_OUTPUT, 4) /* (AE25) PRG0_PRU1_GPO14.RGMII4_TD3 */
> + J721E_IOPAD(0x140, PIN_OUTPUT, 4) /* (AG29) PRG0_PRU1_GPO16.RGMII4_TXC */
> + J721E_IOPAD(0x13c, PIN_OUTPUT, 4) /* (AF29) PRG0_PRU1_GPO15.RGMII4_TX_CTL */
> + >;
> + };
> +};
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@...com>
--
Regards,
Ravi
Powered by blists - more mailing lists