| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <ZMQU7ap9CxfY5eIu@standask-GA-A55M-S2HP>
Date: Fri, 28 Jul 2023 21:20:13 +0200
From: Stanislav Jakubek <stano.jakubek@...il.com>
To: Linus Walleij <linus.walleij@...aro.org>,
Bartosz Golaszewski <brgl@...ev.pl>,
Andy Shevchenko <andy@...nel.org>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Conor Dooley <conor+dt@...nel.org>,
Florian Fainelli <florian.fainelli@...adcom.com>,
Ray Jui <rjui@...adcom.com>,
Scott Branden <sbranden@...adcom.com>
Cc: bcm-kernel-feedback-list@...adcom.com, linux-gpio@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org
Subject: [RFC] dt-bindings: gpio: brcm,kona-gpio: convert to YAML
Convert Broadcom Kona family GPIO controller bindings to DT schema.
Changes during conversion:
- add used, but previously undocumented SoC-specific compatibles
Signed-off-by: Stanislav Jakubek <stano.jakubek@...il.com>
---
RFC since dt_binding_check is giving me these errors/warnings:
Documentation/devicetree/bindings/gpio/brcm,kona-gpio.example.dts:21.23-34.11: Warning (interrupts_property): /example-0/gpio@...03000: Missing interrupt-parent
The old txt bindings and all current DTs do not use interrupt-parent AFAICT,
so I'm not sure what to do about that.
Documentation/devicetree/bindings/gpio/brcm,kona-gpio.example.dtb: gpio@...03000: interrupts: [[0], [106], [4], [0], [115], [4], [0], [114], [4], [0], [113], [4], [0], [112], [4], [0], [111], [4]] is too long
Here I'm not even sure what the issue is.
.../bindings/gpio/brcm,kona-gpio.txt | 52 -------------
.../bindings/gpio/brcm,kona-gpio.yaml | 77 +++++++++++++++++++
MAINTAINERS | 2 +-
3 files changed, 78 insertions(+), 53 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt
create mode 100644 Documentation/devicetree/bindings/gpio/brcm,kona-gpio.yaml
diff --git a/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt
deleted file mode 100644
index 4a63bc96b687..000000000000
--- a/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt
+++ /dev/null
@@ -1,52 +0,0 @@
-Broadcom Kona Family GPIO
-=========================
-
-This GPIO driver is used in the following Broadcom SoCs:
- BCM11130, BCM11140, BCM11351, BCM28145, BCM28155
-
-The Broadcom GPIO Controller IP can be configured prior to synthesis to
-support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The
-GPIO controller only supports edge, not level, triggering of interrupts.
-
-Required properties
--------------------
-
-- compatible: "brcm,bcm11351-gpio", "brcm,kona-gpio"
-- reg: Physical base address and length of the controller's registers.
-- interrupts: The interrupt outputs from the controller. There is one GPIO
- interrupt per GPIO bank. The number of interrupts listed depends on the
- number of GPIO banks on the SoC. The interrupts must be ordered by bank,
- starting with bank 0. There is always a 1:1 mapping between banks and
- IRQs.
-- #gpio-cells: Should be <2>. The first cell is the pin number, the second
- cell is used to specify optional parameters:
- - bit 0 specifies polarity (0 for normal, 1 for inverted)
- See also "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt.
-- #interrupt-cells: Should be <2>. The first cell is the GPIO number. The
- second cell is used to specify flags. The following subset of flags is
- supported:
- - trigger type (bits[1:0]):
- 1 = low-to-high edge triggered.
- 2 = high-to-low edge triggered.
- 3 = low-to-high or high-to-low edge triggered
- Valid values are 1, 2, 3
- See also .../devicetree/bindings/interrupt-controller/interrupts.txt.
-- gpio-controller: Marks the device node as a GPIO controller.
-- interrupt-controller: Marks the device node as an interrupt controller.
-
-Example:
- gpio: gpio@...03000 {
- compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
- reg = <0x35003000 0x800>;
- interrupts =
- <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
- GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
- GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
- GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
- GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH
- GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
- #gpio-cells = <2>;
- #interrupt-cells = <2>;
- gpio-controller;
- interrupt-controller;
- };
diff --git a/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.yaml b/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.yaml
new file mode 100644
index 000000000000..9d0b0a1af832
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/brcm,kona-gpio.yaml
@@ -0,0 +1,77 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/brcm,kona-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom Kona family GPIO controller
+
+description:
+ The Broadcom GPIO Controller IP can be configured prior to synthesis to
+ support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The
+ GPIO controller only supports edge, not level, triggering of interrupts.
+
+maintainers:
+ - Ray Jui <rjui@...adcom.com>
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - brcm,bcm11351-gpio
+ - brcm,bcm21664-gpio
+ - brcm,bcm23550-gpio
+ - const: brcm,kona-gpio
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+ description:
+ The interrupt outputs from the controller. There is one GPIO interrupt
+ per GPIO bank. The number of interrupts listed depends on the number of
+ GPIO banks on the SoC. The interrupts must be ordered by bank, starting
+ with bank 0. There is always a 1:1 mapping between banks and IRQs.
+
+ '#gpio-cells':
+ const: 2
+
+ '#interrupt-cells':
+ const: 2
+
+ gpio-controller: true
+
+ interrupt-controller: true
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - '#gpio-cells'
+ - '#interrupt-cells'
+ - gpio-controller
+ - interrupt-controller
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ gpio@...03000 {
+ compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
+ reg = <0x35003000 0x800>;
+ interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ };
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 733bcfa0209a..368fee1ef5b0 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4221,7 +4221,7 @@ BROADCOM KONA GPIO DRIVER
M: Ray Jui <rjui@...adcom.com>
R: Broadcom internal kernel review list <bcm-kernel-feedback-list@...adcom.com>
S: Supported
-F: Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt
+F: Documentation/devicetree/bindings/gpio/brcm,kona-gpio.yaml
F: drivers/gpio/gpio-bcm-kona.c
BROADCOM MPI3 STORAGE CONTROLLER DRIVER
--
2.34.1
Powered by blists - more mailing lists