[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20230804142820.89593-2-marius.cristea@microchip.com>
Date: Fri, 4 Aug 2023 17:28:19 +0300
From: <marius.cristea@...rochip.com>
To: <jic23@...nel.org>, <lars@...afoo.de>, <robh+dt@...nel.org>
CC: <krzysztof.kozlowski+dt@...aro.org>, <conor+dt@...nel.org>,
<linux-iio@...r.kernel.org>, <devicetree@...r.kernel.org>,
<linux-kernel@...r.kernel.org>, <marius.cristea@...rochip.com>
Subject: [PATCH v3 1/2] dt-bindings: iio: adc: adding MCP3564 ADC
From: Marius Cristea <marius.cristea@...rochip.com>
This is the device tree schema for iio driver for
Microchip family of 153.6 ksps, Low-Noise 16/24-Bit
Delta-Sigma ADCs with an SPI interface (Microchip's
MCP3461, MCP3462, MCP3464, MCP3461R, MCP3462R,
MCP3464R, MCP3561, MCP3562, MCP3564, MCP3561R,
MCP3562R and MCP3564R analog to digital converters).
Signed-off-by: Marius Cristea <marius.cristea@...rochip.com>
---
.../bindings/iio/adc/microchip,mcp3564.yaml | 200 ++++++++++++++++++
1 file changed, 200 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/adc/microchip,mcp3564.yaml
diff --git a/Documentation/devicetree/bindings/iio/adc/microchip,mcp3564.yaml b/Documentation/devicetree/bindings/iio/adc/microchip,mcp3564.yaml
new file mode 100644
index 000000000000..4a264f48a90e
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/microchip,mcp3564.yaml
@@ -0,0 +1,200 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/adc/microchip,mcp3564.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microchip MCP346X and MCP356X ADC Family
+
+maintainers:
+ - Marius Cristea <marius.cristea@...rochip.com>
+
+description: |
+ Bindings for the Microchip family of 153.6 ksps, Low-Noise 16/24-Bit
+ Delta-Sigma ADCs with an SPI interface. Datasheet can be found here:
+ Datasheet for MCP3561, MCP3562, MCP3564 can be found here:
+ https://ww1.microchip.com/downloads/aemDocuments/documents/MSLD/ProductDocuments/DataSheets/MCP3561-2-4-Family-Data-Sheet-DS20006181C.pdf
+ Datasheet for MCP3561R, MCP3562R, MCP3564R can be found here:
+ https://ww1.microchip.com/downloads/aemDocuments/documents/APID/ProductDocuments/DataSheets/MCP3561_2_4R-Data-Sheet-DS200006391C.pdf
+ Datasheet for MCP3461, MCP3462, MCP3464 can be found here:
+ https://ww1.microchip.com/downloads/aemDocuments/documents/APID/ProductDocuments/DataSheets/MCP3461-2-4-Two-Four-Eight-Channel-153.6-ksps-Low-Noise-16-Bit-Delta-Sigma-ADC-Data-Sheet-20006180D.pdf
+ Datasheet for MCP3461R, MCP3462R, MCP3464R can be found here:
+ https://ww1.microchip.com/downloads/aemDocuments/documents/APID/ProductDocuments/DataSheets/MCP3461-2-4R-Family-Data-Sheet-DS20006404C.pdf
+
+properties:
+ compatible:
+ enum:
+ - microchip,mcp3461
+ - microchip,mcp3462
+ - microchip,mcp3464
+ - microchip,mcp3461r
+ - microchip,mcp3462r
+ - microchip,mcp3464r
+ - microchip,mcp3561
+ - microchip,mcp3562
+ - microchip,mcp3564
+ - microchip,mcp3561r
+ - microchip,mcp3562r
+ - microchip,mcp3564r
+
+ reg:
+ maxItems: 1
+
+ spi-max-frequency:
+ maximum: 20000000
+
+ spi-cpha: true
+
+ spi-cpol: true
+
+ vdd-supply: true
+
+ avdd-supply: true
+
+ clocks:
+ description:
+ Phandle and clock identifier for external sampling clock.
+ If not specified, the internal crystal oscillator will be used.
+ maxItems: 1
+
+ interrupts:
+ description: IRQ line of the ADC
+ maxItems: 1
+
+ drive-open-drain:
+ description:
+ Whether to drive the IRQ signal as push-pull (default) or open-drain. Note
+ that the device requires this pin to become "high", otherwise it will stop
+ converting.
+ type: boolean
+
+ vref-supply:
+ description:
+ Some devices have a specific reference voltage supplied on a different
+ pin to the other supplies. Needed to be able to establish channel scaling
+ unless there is also an internal reference available (e.g. mcp3564r). In
+ case of "r" devices (e. g. mcp3564r), if it does not exists the internal
+ reference will be used.
+
+ microchip,hw-device-address:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 3
+ description:
+ The address is set on a per-device basis by fuses in the factory,
+ configured on request. If not requested, the fuses are set for 0x1.
+ The device address is part of the device markings to avoid
+ potential confusion. This address is coded on two bits, so four possible
+ addresses are available when multiple devices are present on the same
+ SPI bus with only one Chip Select line for all devices.
+ Each device communication starts by a CS falling edge, followed by the
+ clocking of the device address (BITS[7:6] - top two bits of COMMAND BYTE
+ which is first one on the wire).
+
+ "#io-channel-cells":
+ const: 1
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+patternProperties:
+ "^channel@([0-9]|([1-7][0-9]))$":
+ $ref: adc.yaml
+ type: object
+ unevaluatedProperties: false
+ description: Represents the external channels which are connected to the ADC.
+
+ properties:
+ reg:
+ description: The channel number in single-ended and differential mode.
+ minimum: 0
+ maximum: 79
+
+ required:
+ - reg
+
+dependencies:
+ spi-cpol: [ spi-cpha ]
+ spi-cpha: [ spi-cpol ]
+
+required:
+ - compatible
+ - reg
+ - microchip,hw-device-address
+ - spi-max-frequency
+
+allOf:
+ - $ref: /schemas/spi/spi-peripheral-props.yaml#
+ - # External vref, no internal reference
+ if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - microchip,mcp3461
+ - microchip,mcp3462
+ - microchip,mcp3464
+ - microchip,mcp3561
+ - microchip,mcp3562
+ - microchip,mcp3564
+ then:
+ required:
+ - vref-supply
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ adc@0 {
+ compatible = "microchip,mcp3564r";
+ reg = <0>;
+ vref-supply = <&vref_reg>;
+ spi-cpha;
+ spi-cpol;
+ spi-max-frequency = <10000000>;
+ microchip,hw-device-address = <1>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@0 {
+ /* CH0 to AGND */
+ reg = <0>;
+ };
+
+ channel@1 {
+ /* CH1 to AGND */
+ reg = <1>;
+ };
+
+ /* diff-channels */
+ channel@11 {
+ reg = <11>;
+
+ /* CN0, CN1 */
+ diff-channels = <0 1>;
+ };
+
+ channel@22 {
+ reg = <0x22>;
+
+ /* CN1, CN2 */
+ diff-channels = <1 2>;
+ };
+
+ channel@23 {
+ reg = <0x23>;
+
+ /* CN1, CN3 */
+ diff-channels = <1 3>;
+ };
+ };
+ };
+...
--
2.34.1
Powered by blists - more mailing lists