[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <trcp4f77dv2e36zpe53s7sjoyevgd5qtpv6m4a75ryalglqnev@trcsnsmvtijy>
Date: Fri, 18 Aug 2023 21:19:59 +0300
From: Serge Semin <fancer.lancer@...il.com>
To: Rohan G Thomas <rohan.g.thomas@...el.com>
Cc: "David S . Miller" <davem@...emloft.net>,
Alexandre Torgue <alexandre.torgue@...s.st.com>,
Jose Abreu <joabreu@...opsys.com>,
Eric Dumazet <edumazet@...gle.com>,
Jakub Kicinski <kuba@...nel.org>,
Paolo Abeni <pabeni@...hat.com>,
Maxime Coquelin <mcoquelin.stm32@...il.com>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Conor Dooley <conor+dt@...nel.org>,
Giuseppe Cavallaro <peppe.cavallaro@...com>,
netdev@...r.kernel.org, linux-stm32@...md-mailman.stormreply.com,
linux-arm-kernel@...ts.infradead.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org
Subject: Re: [PATCH net-next v4 2/2] net: stmmac: Tx coe sw fallback
On Fri, Aug 18, 2023 at 09:53:50PM +0800, Rohan G Thomas wrote:
> Add sw fallback of tx checksum calculation for those tx queues that
> don't support tx checksum offloading. Because, some DWMAC IPs support
> tx checksum offloading only for a few initial tx queues, starting
> from tx queue 0.
>
> Signed-off-by: Rohan G Thomas <rohan.g.thomas@...el.com>
> ---
> drivers/net/ethernet/stmicro/stmmac/stmmac.h | 5 +++++
> .../net/ethernet/stmicro/stmmac/stmmac_main.c | 19 +++++++++++++++++++
> .../ethernet/stmicro/stmmac/stmmac_platform.c | 4 ++++
> include/linux/stmmac.h | 1 +
> 4 files changed, 29 insertions(+)
>
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> index 3401e888a9f6..64d7dbe474bd 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> @@ -210,12 +210,17 @@ struct stmmac_dma_conf {
> unsigned int dma_tx_size;
> };
>
> +#define STMMAC_PRIV_FLG_TXQ_COE_LIMIT BIT(0)
> +
> struct stmmac_priv {
> /* Frequently used values are kept adjacent for cache effect */
> u32 tx_coal_frames[MTL_MAX_TX_QUEUES];
> u32 tx_coal_timer[MTL_MAX_TX_QUEUES];
> u32 rx_coal_frames[MTL_MAX_TX_QUEUES];
>
> + u32 flags;
This looks redundant. See my last comment.
> +
> + u32 tx_q_with_coe;
This one too. Can't you just use the
plat_stmmacenet_data.tx_queues_with_coe field?
> int hwts_tx_en;
> bool tx_path_in_lpi_mode;
> bool tso;
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> index 733b5e900817..f9ab6635218c 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> @@ -4409,6 +4409,17 @@ static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)
> WARN_ON(tx_q->tx_skbuff[first_entry]);
>
> csum_insertion = (skb->ip_summed == CHECKSUM_PARTIAL);
> + /* Some DWMAC IPs support tx coe only for a few initial tx queues,
> + * starting from tx queue 0. So checksum offloading for those queues
> + * that don't support tx coe needs to fallback to software checksum
> + * calculation.
> + */
> + if (csum_insertion && (priv->flags & STMMAC_PRIV_FLG_TXQ_COE_LIMIT) &&
> + queue >= priv->tx_q_with_coe) {
> + if (unlikely(skb_checksum_help(skb)))
> + goto dma_map_err;
> + csum_insertion = !csum_insertion;
> + }
just (csum_insertion && queue >= priv->plat->tx_queues_with_coe). See
further what to do for this to work as I suggested.
>
> if (likely(priv->extend_desc))
> desc = (struct dma_desc *)(tx_q->dma_etx + entry);
> @@ -7401,6 +7412,14 @@ int stmmac_dvr_probe(struct device *device,
> dev_info(priv->device, "SPH feature enabled\n");
> }
>
> + if (priv->plat->tx_coe &&
> + priv->plat->tx_queues_with_coe < priv->plat->tx_queues_to_use) {
> + priv->flags |= STMMAC_PRIV_FLG_TXQ_COE_LIMIT;
> + priv->tx_q_with_coe = priv->plat->tx_queues_with_coe;
> + dev_info(priv->device, "TX COE limited to %u tx queues\n",
> + priv->tx_q_with_coe);
> + }
What about:
+ if (priv->plat->tx_coe && !priv->plat->tx_queues_with_coe)
+ priv->plat->tx_queues_with_coe = priv->plat->tx_queues_to_use;
+ else if (!priv->plat->tx_coe)
+ priv->plat->tx_queues_with_coe = 0;
+ else if (priv->plat->tx_queues_with_coe < priv->plat->tx_queues_to_use)
+ dev_info(priv->device, "TX COE is available for %u queues\n", priv->plat->tx_queues_with_coe);
?
-Serge(y)
> +
> /* Ideally our host DMA address width is the same as for the
> * device. However, it may differ and then we have to use our
> * host DMA width for allocation and the device DMA width for
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
> index be8e79c7aa34..0138b7c9c7ab 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
> @@ -225,6 +225,10 @@ static int stmmac_mtl_setup(struct platform_device *pdev,
> &plat->tx_queues_to_use))
> plat->tx_queues_to_use = 1;
>
> + if (of_property_read_u32(tx_node, "snps,tx-queues-with-coe",
> + &plat->tx_queues_with_coe))
> + plat->tx_queues_with_coe = plat->tx_queues_to_use;
> +
> if (of_property_read_bool(tx_node, "snps,tx-sched-wrr"))
> plat->tx_sched_algorithm = MTL_TX_ALGORITHM_WRR;
> else if (of_property_read_bool(tx_node, "snps,tx-sched-wfq"))
> diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
> index 784277d666eb..cb508164eaea 100644
> --- a/include/linux/stmmac.h
> +++ b/include/linux/stmmac.h
> @@ -252,6 +252,7 @@ struct plat_stmmacenet_data {
> u32 host_dma_width;
> u32 rx_queues_to_use;
> u32 tx_queues_to_use;
> + u32 tx_queues_with_coe;
> u8 rx_sched_algorithm;
> u8 tx_sched_algorithm;
> struct stmmac_rxq_cfg rx_queues_cfg[MTL_MAX_RX_QUEUES];
> --
> 2.19.0
>
>
Powered by blists - more mailing lists