linux-kernel - RE: [PATCH net-next v3 1/2] net/ethernet/realtek: Add Realtek automotive PCIe driver code

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <4951391892534eaeb2da96f052364e4c@realtek.com>
Date:   Fri, 18 Aug 2023 11:56:28 +0000
From:   Justin Lai <justinlai0215@...ltek.com>
To:     Andrew Lunn <andrew@...n.ch>
CC:     "kuba@...nel.org" <kuba@...nel.org>,
        "davem@...emloft.net" <davem@...emloft.net>,
        "edumazet@...gle.com" <edumazet@...gle.com>,
        "pabeni@...hat.com" <pabeni@...hat.com>,
        "linux-kernel@...r.kernel.org" <linux-kernel@...r.kernel.org>,
        "netdev@...r.kernel.org" <netdev@...r.kernel.org>
Subject: RE: [PATCH net-next v3 1/2] net/ethernet/realtek: Add Realtek automotive PCIe driver code

> On Thu, Aug 17, 2023 at 07:32:07AM +0000, Justin Lai wrote:
> > > On Tue, Aug 15, 2023 at 10:37:55PM +0800, Justin Lai wrote:
> > > > This patch is to add the ethernet device driver for the PCIe
> > > > interface of Realtek Automotive Ethernet Switch, applicable to
> > > > RTL9054, RTL9068,
> > > RTL9072, RTL9075, RTL9068, RTL9071.
> > > >
> > > > Below is a simplified block diagram of the chip and its relevant
> interfaces.
> > > >
> > > >           *************************
> > > >           *                       *
> > > >           *  CPU network device   *
> > > >           *    ____________       *
> > > >           *   |            |      *
> > > >           *   |  PCIE Host |      *
> > > >           *************************
> > > >                     ||
> > > >                    PCIE
> > > >                     ||
> > > >   ****************************************
> > > >   *          | PCIE Endpoint |           *
> > > >   *          |---------------|           *
> > > >   *              | GMAC |                *
> > > >   *              |------|  Realtek       *
> > > >   *                 ||   RTL90xx Series  *
> > > >   *                 ||                   *
> > > >   *    _____________||______________     *
> > > >   *   |            |MAC|            |    *
> > > >   *   |            |---|            |    *
> > > >   *   |                             |    *
> > > >   *   |     Ethernet Switch Core    |    *
> > > >   *   |                             |    *
> > > >   *   |  -----             -----    |    *
> > > >   *   |  |MAC| ............|MAC|    |    *
> > > >   *   |__|___|_____________|___|____|    *
> > > >   *      |PHY| ............|PHY|         *
> > > >   *      -----             -----         *
> > > >   *********||****************||***********
> > > > This driver is mainly used to control GMAC, but does not control
> > > > the switch
> > > core, so it is not the same as DSA.
> > > > In addition, the GMAC is not directly connected to the PHY, but
> > > > directly connected to the mac of the switch core, so there is no
> > > > need for PHY
> > > handing.
> > >
> > > So this describes your board? Is the MAC and the swtich two separate
> > > chips? Is it however possible to connect the GMAC to a PHY? Could
> > > some OEM purchase the chipset and build a board with a PHY? We write
> > > MAC drivers around what the MAC can do, not what one specific board
> allows.
> > >
> > > What MAC drivers do to support being connected to a switch like this
> > > is use a fixed-link PHY, via phylink. This gives a virtual PHY, which supports
> one speed.
> > > The MAC driver then just uses the phylink API as normal.
> > >
> > > On your board, how is the switch controlled? Is there an MDIO bus as
> > > part of the MAC? If so, you should add an MDIO bus master driver.
> >
> >
> > Hi, Andrew
> >
> > The block of the Realtek RTL90xx series is our entire chip
> > architecture, the GMAC is connected to the switch core, and there is
> > no PHY in between. So customers don't need to consider that.
> 
> O.K. It would of been helpful if you had said this right at the beginning. It is
> good to point out anything unusual with your hardware, otherwise reviewers
> are going to make wrong assumptions, and then ask lots of questions.
> 
> Is the 'line' speed of the MAC fixed? It operates at one speed, and that is it?

Hi, Andrew

The "line" speed of the MAC is fixed 5G, but the throughput will be determined according to the speed of the PCIe link. For example, if the link speed is gen 3, the throughput will be 5G. if the link speed is gen 2, the throughput will be 2.5G. if the link speed is gen 1, the throughput will be 1G.

> What about pause? You cannot negotiate pause, but can it be forced?
We do not support negotiate pause, but it can be forced.
 
> > We have some externally controlled interfaces to control switch core,
> > such as I2C, MDIO, SPI, etc., but these are not controlled by GMAC .
> 
> And just for conformation, there is no extra fields in the DMA descriptors, etc,
> to help the switch? You will at some point write a DSA driver for the switch,
> and there will be a tagging protocol, extra headers added to the frame, in
> order to direct frames out the correct port of the switch?

There is no extra fields in DMA descriptors for tagging protocol. The tag added by switch hardware instead of this driver.
> 
> Are the I2C, MDIO and SPI bus masters also hanging off a PCIE endpoint? Can
> they probe independently? I'm just want to check this should not be part of an
> MFD driver.

The I2C, MDIO and SPI bus masters are not hanging off the PCIE endpoints, but on the switch core.
> 
> Is there a public data sheet for this device?

We currently do not have a public data sheet to provide.
> 
>         Andrew
>