| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20230821201146.hudnk5v2zugz726p@skbuf>
Date: Mon, 21 Aug 2023 23:11:46 +0300
From: Vladimir Oltean <vladimir.oltean@....com>
To: Rob Herring <robh@...nel.org>
Cc: netdev@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org, linux-phy@...ts.infradead.org,
"Russell King (Oracle)" <rmk+kernel@...linux.org.uk>,
Heiner Kallweit <hkallweit1@...il.com>,
Andrew Lunn <andrew@...n.ch>,
Florian Fainelli <f.fainelli@...il.com>,
Madalin Bucur <madalin.bucur@....com>,
Ioana Ciornei <ioana.ciornei@....com>,
Camelia Groza <camelia.groza@....com>,
Li Yang <leoyang.li@....com>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Conor Dooley <conor@...nel.org>,
Sean Anderson <sean.anderson@...o.com>,
Maxime Chevallier <maxime.chevallier@...tlin.com>,
Vinod Koul <vkoul@...nel.org>,
Kishon Vijay Abraham I <kishon@...nel.org>
Subject: Re: [RFC PATCH net-next 8/8] dt-bindings: net: fsl,backplane-anlt:
new binding document
Hi Rob,
On Mon, Aug 21, 2023 at 02:58:40PM -0500, Rob Herring wrote:
> On Thu, Aug 17, 2023 at 06:06:44PM +0300, Vladimir Oltean wrote:
> > Illustrate how the backplane AN/LT blocks can be instantiated on the
> > LX2160A SoC with SerDes protocol 19.
> >
> > Signed-off-by: Vladimir Oltean <vladimir.oltean@....com>
> > ---
> > .../devicetree/bindings/net/ethernet-phy.yaml | 8 +
> > .../bindings/net/fsl,backplane-anlt.yaml | 238 ++++++++++++++++++
> > 2 files changed, 246 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/net/fsl,backplane-anlt.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/net/ethernet-phy.yaml b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
> > index c1241c8a3b77..96fa672e4786 100644
> > --- a/Documentation/devicetree/bindings/net/ethernet-phy.yaml
> > +++ b/Documentation/devicetree/bindings/net/ethernet-phy.yaml
> > @@ -49,6 +49,14 @@ properties:
> > - items:
> > - pattern: "^ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$"
> > - const: ethernet-phy-ieee802.3-c45
> > + - items:
> > + - const: fsl,lx2160a-backplane-anlt
> > + - const: ethernet-phy-ieee802.3-c45
>
> What's the benefit of having ethernet-phy-ieee802.3-c45? Will it work if
> the OS only understands that and not fsl,lx2160a-backplane-anlt?
No. The "is_c45" bool won't get set correctly in fwnode_mdiobus_register_phy().
is_c45 = fwnode_device_is_compatible(child, "ethernet-phy-ieee802.3-c45");
With that bool set incorrectly, the MDIO protocol cannot access the device's
registers.
> > + description:
> > + Some C45 PHYs have no PHY ID in the standard location, and there is
> > + also no PHY ID allocated for them to fake. They are identified by the
> > + primary compatible string, plus the secondary one to distinguish them
> > + from a raw MDIO device.
> >
> > reg:
> > minimum: 0
> > diff --git a/Documentation/devicetree/bindings/net/fsl,backplane-anlt.yaml b/Documentation/devicetree/bindings/net/fsl,backplane-anlt.yaml
> > new file mode 100644
> > index 000000000000..7282e93b1dd4
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/net/fsl,backplane-anlt.yaml
> > @@ -0,0 +1,238 @@
> > +# SPDX-License-Identifier: GPL-2.0+
>
> Not the right license.
What's wrong with it?
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/net/fsl,backplane-anlt.yaml
> > +$schema: http://devicetree.org/meta-schemas/core.yaml
> > +
> > +title: Freescale Backplane Ethernet PHY
> > +
> > +maintainers:
> > + - Vladimir Oltean <vladimir.oltean@....com>
> > +
> > +description: |
> > + Some QorIQ and Layerscape SoCs have an additional block on each SerDes
> > + networking lane, based on an IP core from MoreThanIP, which performs IEEE
> > + 802.3 clause 73 base page exchanges (for auto-negotiation) and clause 72
> > + training frame exchanges (for link training).
> > +
> > + By default, this AN/LT block comes up with auto-negotiation disabled, and
> > + in that case it allows itself to be quickly bypassed from the data path and
> > + for the PCS link to come up without its involvement.
> > +
> > + Software can optionally make use of it, to turn the PCS, AN/LT block and lane
> > + (PMA/PMD) into a full copper backplane internal PHY.
> > +
> > + As a warning, the binding for the multi-lane link modes (40GBase-KR4) is not
> > + currently backed up by a driver implementation.
> > +
> > +allOf:
> > + - if:
> > + properties:
> > + compatible:
> > + - items:
> > + - const: fsl,lx2160a-backplane-anlt
> > + - const: ethernet-phy-ieee802.3-c45
>
> Use "contains" and drop ethernet-phy-ieee802.3-c45.
Thanks, I'll try it.
> > + then:
> > + $ref: ethernet-phy.yaml#
> > +
> > +properties:
> > + compatible:
> > + oneOf:
> > + - items:
> > + - const: fsl,lx2160a-backplane-anlt
> > + - const: ethernet-phy-ieee802.3-c45
> > + - const: fsl,lx2160a-secondary-anlt
> > +
> > + reg:
> > + minimum: 0
> > + maximum: 31
> > + description: |
> > + The address of the AN/LT block within the internal MDIO bus of the MAC it
> > + is attached to.
> > +
> > + In the 1000Base-KX and 10GBase-KR link modes, the AN/LT block responds at
> > + the same MDIO address as the PCS (determined by the SGMIInCR1[MDEV_PORT]
> > + or SXGMIInCR1[MDEV_PORT] registers of the SerDes block, by default 0).
> > + The PCS and AN/LT block respond to different MMDs, though.
> > +
> > + In the 25GBase-KR and higher link modes, the AN/LT block responds at a
> > + different MDIO address than the PCS, determined by the
> > + ANLTnCR1[MDEV_PORT] register of the SerDes block. By default this is 4
> > + for lanes A and E, 5 for lanes B and F, 6 for lanes C and G, 7 for lanes
> > + D and H.
> > +
> > + The PCS responds in all cases at the address determined by the MDEV_PORT
> > + field of the SGMIInCR1, SXGMIIaCR1, E25GaCR1, E40GaCR1, E50GaCR1 or
> > + E100GaCR1 registers of the SerDes block.
> > +
> > + phys:
> > + maxItems: 1
> > + description:
> > + phandle for the generic PHY (SerDes lane) that acts as PMA/PMD layer
> > +
> > + pcs-handle:
> > + maxItems: 1
> > + description:
> > + phandle for the technology-dependent PCS block corresponding to the
> > + initial (RCW-based) configuration of the port. Must be omitted for the
> > + link modes where the PCS and AN/LT block respond at the same MDIO
> > + address. Must be specified otherwise.
> > +
> > + secondary-anlt-handle:
>
> Needs a vendor prefix and type.
Ok (assuming this will remain in the final solution, after PHY maintainers' review)
> > + maxItems: 1
> > + description:
> > + In case this is the primary (first) lane of a multi-lane link mode, this
> > + property holds an array of phandles for the other AN/LT blocks, that are
> > + involved in link training but not in auto-negotiation. These have the
> > + "fsl,lx2160a-secondary-anlt" compatible string.
> > +
> > +required:
> > + - compatible
> > + - reg
> > + - phys
> > +
> > +unevaluatedProperties: false
> > +
> > +examples:
> > +
> > + # LX2160A lanes A, B, C, D with SerDes 1 protocol 19: dpmac2 uses 40GBase-KR4
> > + - |
> > + dpmac2 {
> > + phy-handle = <&mac2_backplane_anlt>;
> > + phy-connection-type = "internal";
> > + };
> > +
> > + pcs_mdio2 {
>
> mdio {
Hmm, is it bad if I can keep the name? (it's actually important for documentary purposes)
Actually I wanted to put a label like "pcs_mdio2: mdio {", but I couldn't,
and this is what led me to the compromise.
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + status = "okay";
>
> Don't need status in examples.
Ok.
> > +
> > + pcs2: ethernet-phy@0 {
> > + reg = <0>;
> > + };
> > +
> > + mac2_backplane_anlt: ethernet-phy@7 {
> > + compatible = "fsl,lx2160a-backplane-anlt",
> > + "ethernet-phy-ieee802.3-c45";
> > + reg = <7>; /* according to ANLTDCR1[MDEV_PORT] */
> > + phys = <&serdes_1 3>; /* lane D */
> > + max-speed = <40000>;
> > + pcs-handle = <&pcs2>;
> > + secondary-anlt-handle = <&mac2_lane2_anlt>, <&mac2_lane3_anlt>,
> > + <&mac2_lane4_anlt>;
> > + };
> > +
> > + mac2_lane2_anlt: ethernet-backplane-anlt@6 {
> > + compatible = "fsl,lx2160a-secondary-anlt";
> > + reg = <6>; /* according to ANLTCCR1[MDEV_PORT] */
> > + phys = <&serdes_1 2>; /* lane C */
> > + };
> > +
> > + mac2_lane3_anlt: ethernet-backplane-anlt@5 {
> > + compatible = "fsl,lx2160a-secondary-anlt";
> > + reg = <5>; /* according to ANLTBCR1[MDEV_PORT] */
> > + phys = <&serdes_1 1>; /* lane B */
> > + };
> > +
> > + mac2_lane4_anlt: ethernet-backplane-anlt@4 {
> > + compatible = "fsl,lx2160a-secondary-anlt";
> > + reg = <4>; /* according to ANLTACR1[MDEV_PORT] */
> > + phys = <&serdes_1 0>; /* lane A */
> > + };
> > + };
> > +
> > + # LX2160A lane E with SerDes 1 protocol 19: dpmac6 uses 25GBase-KR
> > + - |
> > + dpmac6 {
> > + phy-handle = <&mac6_backplane_anlt>;
> > + phy-connection-type = "internal";
> > + };
> > +
> > + pcs_mdio6 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + status = "okay";
> > +
> > + pcs6: ethernet-phy@0 {
> > + reg = <0>;
> > + };
> > +
> > + mac6_backplane_anlt: ethernet-phy@4 {
> > + compatible = "fsl,lx2160a-backplane-anlt",
> > + "ethernet-phy-ieee802.3-c45";
> > + reg = <4>; /* according to ANLTFCR1[MDEV_PORT] */
> > + phys = <&serdes_1 4>; /* lane E */
> > + max-speed = <25000>;
> > + pcs-handle = <&pcs6>;
> > + };
> > + };
> > +
> > + # LX2160A lane F with SerDes 1 protocol 19: dpmac5 uses 25GBase-KR
> > + - |
> > + dpmac5 {
> > + phy-handle = <&mac5_backplane_anlt>;
> > + phy-connection-type = "internal";
> > + };
> > +
> > + pcs_mdio5 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + status = "okay";
> > +
> > + pcs5: ethernet-phy@0 {
> > + reg = <0>;
> > + };
> > +
> > + mac5_backplane_anlt: ethernet-phy@5 {
> > + compatible = "fsl,lx2160a-backplane-anlt",
> > + "ethernet-phy-ieee802.3-c45";
> > + reg = <5>; /* according to ANLTFCR1[MDEV_PORT] */
> > + phys = <&serdes_1 5>; /* lane F */
> > + max-speed = <25000>;
> > + pcs-handle = <&pcs5>;
> > + };
> > + };
> > +
> > + # LX2160A lane G with SerDes 1 protocol 19: dpmac4 uses 10GBase-KR
> > + - |
> > + dpmac4 {
> > + phy-handle = <&mac4_backplane_anlt>;
> > + phy-connection-type = "internal";
> > + };
> > +
> > + pcs_mdio4 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + status = "okay";
> > +
> > + mac4_backplane_anlt: ethernet-phy@0 {
> > + compatible = "fsl,lx2160a-backplane-anlt",
> > + "ethernet-phy-ieee802.3-c45";
> > + reg = <0>; /* merged with PCS SXGMIIGCR1[MDEV_PORT] */
> > + phys = <&serdes_1 7>; /* lane G */
> > + max-speed = <10000>;
> > + /* no pcs-handle to &pcs4 */
> > + };
> > + };
> > +
> > + # LX2160A lane H with SerDes 1 protocol 19: dpmac3 uses 10GBase-KR
> > + - |
> > + dpmac3 {
> > + phy-handle = <&mac3_backplane_anlt>;
> > + phy-connection-type = "internal";
> > + };
> > +
> > + pcs_mdio3 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + status = "okay";
> > +
> > + mac3_backplane_anlt: ethernet-phy@0 {
> > + compatible = "fsl,lx2160a-backplane-anlt",
> > + "ethernet-phy-ieee802.3-c45";
> > + reg = <0>; /* merged with PCS SXGMIIHCR1[MDEV_PORT] */
> > + phys = <&serdes_1 7>; /* lane H */
> > + max-speed = <10000>;
> > + /* no pcs-handle to &pcs3 */
> > + };
> > + };
>
> 5 examples yet not one for "fsl,lx2160a-secondary-anlt"
Are you sure? They're in the first one:
"LX2160A lanes A, B, C, D with SerDes 1 protocol 19: dpmac2 uses 40GBase-KR4"
(and still not trimmed from this email)
Powered by blists - more mailing lists