| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <qm3whvpvf3i344hmmq4jdiy6qdl6g2gx64vuvnce2mv2fxylnx@ubkniiinqc7a>
Date: Mon, 28 Aug 2023 20:46:22 +0300
From: Serge Semin <fancer.lancer@...il.com>
To: Jisheng Zhang <jszhang@...nel.org>
Cc: "David S . Miller" <davem@...emloft.net>,
Eric Dumazet <edumazet@...gle.com>,
Jakub Kicinski <kuba@...nel.org>,
Paolo Abeni <pabeni@...hat.com>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Conor Dooley <conor+dt@...nel.org>,
Giuseppe Cavallaro <peppe.cavallaro@...com>,
Alexandre Torgue <alexandre.torgue@...s.st.com>,
Jose Abreu <joabreu@...opsys.com>, Maxime@....codeaurora.org,
Coquelin@....codeaurora.org,
Simon Horman <simon.horman@...igine.com>,
netdev@...r.kernel.org, devicetree@...r.kernel.org,
linux-kernel@...r.kernel.org,
linux-stm32@...md-mailman.stormreply.com,
linux-arm-kernel@...ts.infradead.org,
linux-riscv@...ts.infradead.org
Subject: Re: [PATCH net-next v2 3/3] net: stmmac: add glue layer for T-HEAD
TH1520 SoC
On Tue, Aug 29, 2023 at 12:13:58AM +0800, Jisheng Zhang wrote:
> On Mon, Aug 28, 2023 at 06:58:11PM +0300, Serge Semin wrote:
> > On Sun, Aug 27, 2023 at 05:17:10PM +0800, Jisheng Zhang wrote:
> > > Add dwmac glue driver to support the dwmac on the T-HEAD TH1520 SoC.
> > >
> > > Signed-off-by: Jisheng Zhang <jszhang@...nel.org>
> > > ---
> > > drivers/net/ethernet/stmicro/stmmac/Kconfig | 11 +
> > > drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
> > > .../net/ethernet/stmicro/stmmac/dwmac-thead.c | 302 ++++++++++++++++++
> > > 3 files changed, 314 insertions(+)
> > > create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-thead.c
> > >
> > > diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > > index 06c6871f8788..1bf71804c270 100644
> > > --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > > +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> > > @@ -216,6 +216,17 @@ config DWMAC_SUN8I
> > > stmmac device driver. This driver is used for H3/A83T/A64
> > > EMAC ethernet controller.
> > >
> > > +config DWMAC_THEAD
> > > + tristate "T-HEAD dwmac support"
> > > + depends on OF && (ARCH_THEAD || COMPILE_TEST)
> > > + select MFD_SYSCON
> > > + help
> > > + Support for ethernet controllers on T-HEAD RISC-V SoCs
> > > +
> > > + This selects the T-HEAD platform specific glue layer support for
> > > + the stmmac device driver. This driver is used for T-HEAD TH1520
> > > + ethernet controller.
> > > +
> > > config DWMAC_IMX8
> > > tristate "NXP IMX8 DWMAC support"
> > > default ARCH_MXC
> > > diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
> > > index 5b57aee19267..d73171ed6ad7 100644
> > > --- a/drivers/net/ethernet/stmicro/stmmac/Makefile
> > > +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
> > > @@ -27,6 +27,7 @@ obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o
> > > obj-$(CONFIG_DWMAC_STM32) += dwmac-stm32.o
> > > obj-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o
> > > obj-$(CONFIG_DWMAC_SUN8I) += dwmac-sun8i.o
> > > +obj-$(CONFIG_DWMAC_THEAD) += dwmac-thead.o
> > > obj-$(CONFIG_DWMAC_DWC_QOS_ETH) += dwmac-dwc-qos-eth.o
> > > obj-$(CONFIG_DWMAC_INTEL_PLAT) += dwmac-intel-plat.o
> > > obj-$(CONFIG_DWMAC_GENERIC) += dwmac-generic.o
> > > diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-thead.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-thead.c
> > > new file mode 100644
> > > index 000000000000..85135ef05906
> > > --- /dev/null
> > > +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-thead.c
> > > @@ -0,0 +1,302 @@
> > > +// SPDX-License-Identifier: GPL-2.0
> > > +/*
> > > + * T-HEAD DWMAC platform driver
> > > + *
> > > + * Copyright (C) 2021 Alibaba Group Holding Limited.
> > > + * Copyright (C) 2023 Jisheng Zhang <jszhang@...nel.org>
> > > + *
> > > + */
> > > +
> > > +#include <linux/bitfield.h>
> > > +#include <linux/mfd/syscon.h>
> > > +#include <linux/module.h>
> > > +#include <linux/of.h>
> > > +#include <linux/of_device.h>
> > > +#include <linux/of_net.h>
> > > +#include <linux/platform_device.h>
> > > +#include <linux/regmap.h>
> > > +
> > > +#include "stmmac_platform.h"
> > > +
> > > +#define GMAC_CLK_EN 0x00
> > > +#define GMAC_TX_CLK_EN BIT(1)
> > > +#define GMAC_TX_CLK_N_EN BIT(2)
> > > +#define GMAC_TX_CLK_OUT_EN BIT(3)
> > > +#define GMAC_RX_CLK_EN BIT(4)
> > > +#define GMAC_RX_CLK_N_EN BIT(5)
> > > +#define GMAC_EPHY_REF_CLK_EN BIT(6)
> > > +#define GMAC_RXCLK_DELAY_CTRL 0x04
> > > +#define GMAC_RXCLK_BYPASS BIT(15)
> > > +#define GMAC_RXCLK_INVERT BIT(14)
> > > +#define GMAC_RXCLK_DELAY_MASK GENMASK(4, 0)
> > > +#define GMAC_RXCLK_DELAY_VAL(x) FIELD_PREP(GMAC_RXCLK_DELAY_MASK, (x))
> > > +#define GMAC_TXCLK_DELAY_CTRL 0x08
> > > +#define GMAC_TXCLK_BYPASS BIT(15)
> > > +#define GMAC_TXCLK_INVERT BIT(14)
> > > +#define GMAC_TXCLK_DELAY_MASK GENMASK(4, 0)
> > > +#define GMAC_TXCLK_DELAY_VAL(x) FIELD_PREP(GMAC_RXCLK_DELAY_MASK, (x))
> > > +#define GMAC_PLLCLK_DIV 0x0c
> > > +#define GMAC_PLLCLK_DIV_EN BIT(31)
> > > +#define GMAC_PLLCLK_DIV_MASK GENMASK(7, 0)
> > > +#define GMAC_PLLCLK_DIV_NUM(x) FIELD_PREP(GMAC_PLLCLK_DIV_MASK, (x))
> > > +#define GMAC_GTXCLK_SEL 0x18
> > > +#define GMAC_GTXCLK_SEL_PLL BIT(0)
> > > +#define GMAC_INTF_CTRL 0x1c
> > > +#define PHY_INTF_MASK BIT(0)
> > > +#define PHY_INTF_RGMII FIELD_PREP(PHY_INTF_MASK, 1)
> > > +#define PHY_INTF_MII_GMII FIELD_PREP(PHY_INTF_MASK, 0)
> > > +#define GMAC_TXCLK_OEN 0x20
> > > +#define TXCLK_DIR_MASK BIT(0)
> > > +#define TXCLK_DIR_OUTPUT FIELD_PREP(TXCLK_DIR_MASK, 0)
> > > +#define TXCLK_DIR_INPUT FIELD_PREP(TXCLK_DIR_MASK, 1)
> > > +
> > > +#define GMAC_GMII_RGMII_RATE 125000000
> > > +#define GMAC_MII_RATE 25000000
> > > +
> > > +struct thead_dwmac {
> > > + struct plat_stmmacenet_data *plat;
> > > + struct regmap *apb_regmap;
> > > + struct device *dev;
> > > + u32 rx_delay;
> > > + u32 tx_delay;
> > > +};
> > > +
> > > +static int thead_dwmac_set_phy_if(struct plat_stmmacenet_data *plat)
> > > +{
> > > + struct thead_dwmac *dwmac = plat->bsp_priv;
> > > + u32 phyif;
> > > +
> > > + switch (plat->interface) {
> > > + case PHY_INTERFACE_MODE_MII:
> > > + phyif = PHY_INTF_MII_GMII;
> > > + break;
> > > + case PHY_INTERFACE_MODE_RGMII:
> > > + case PHY_INTERFACE_MODE_RGMII_ID:
> > > + case PHY_INTERFACE_MODE_RGMII_TXID:
> > > + case PHY_INTERFACE_MODE_RGMII_RXID:
> > > + phyif = PHY_INTF_RGMII;
> > > + break;
> > > + default:
> > > + dev_err(dwmac->dev, "unsupported phy interface %d\n",
> > > + plat->interface);
> > > + return -EINVAL;
> > > + };
> > > +
> > > + regmap_write(dwmac->apb_regmap, GMAC_INTF_CTRL, phyif);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int thead_dwmac_set_txclk_dir(struct plat_stmmacenet_data *plat)
> > > +{
> > > + struct thead_dwmac *dwmac = plat->bsp_priv;
> > > + u32 txclk_dir;
> > > +
> > > + switch (plat->interface) {
> > > + case PHY_INTERFACE_MODE_MII:
> > > + txclk_dir = TXCLK_DIR_INPUT;
> > > + break;
> > > + case PHY_INTERFACE_MODE_RGMII:
> > > + case PHY_INTERFACE_MODE_RGMII_ID:
> > > + case PHY_INTERFACE_MODE_RGMII_TXID:
> > > + case PHY_INTERFACE_MODE_RGMII_RXID:
> > > + txclk_dir = TXCLK_DIR_OUTPUT;
> > > + break;
> > > + default:
> > > + dev_err(dwmac->dev, "unsupported phy interface %d\n",
> > > + plat->interface);
> > > + return -EINVAL;
> > > + };
> > > +
> > > + regmap_write(dwmac->apb_regmap, GMAC_TXCLK_OEN, txclk_dir);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static void thead_dwmac_fix_speed(void *priv, unsigned int speed, unsigned int mode)
> > > +{
> > > + struct thead_dwmac *dwmac = priv;
> > > + struct plat_stmmacenet_data *plat = dwmac->plat;
> > > + unsigned long rate;
> > > + u32 div;
> > > +
> > > + switch (plat->interface) {
> > > + /* For MII, rxc/txc is provided by phy */
> > > + case PHY_INTERFACE_MODE_MII:
> > > + return;
> > > +
> > > + case PHY_INTERFACE_MODE_RGMII:
> > > + case PHY_INTERFACE_MODE_RGMII_ID:
> > > + case PHY_INTERFACE_MODE_RGMII_RXID:
> > > + case PHY_INTERFACE_MODE_RGMII_TXID:
> > > + rate = clk_get_rate(plat->stmmac_clk);
> > > + if (!rate || rate % GMAC_GMII_RGMII_RATE != 0 ||
> > > + rate % GMAC_MII_RATE != 0) {
> > > + dev_err(dwmac->dev, "invalid gmac rate %ld\n", rate);
> > > + return;
> > > + }
> > > +
> > > + regmap_update_bits(dwmac->apb_regmap, GMAC_PLLCLK_DIV, GMAC_PLLCLK_DIV_EN, 0);
> > > +
> > > + switch (speed) {
> > > + case SPEED_1000:
> > > + div = rate / GMAC_GMII_RGMII_RATE;
> > > + break;
> > > + case SPEED_100:
> > > + div = rate / GMAC_MII_RATE;
> > > + break;
> > > + case SPEED_10:
> > > + div = rate * 10 / GMAC_MII_RATE;
> > > + break;
> > > + default:
> > > + dev_err(dwmac->dev, "invalid speed %u\n", speed);
> > > + return;
> > > + }
> > > + regmap_update_bits(dwmac->apb_regmap, GMAC_PLLCLK_DIV,
> > > + GMAC_PLLCLK_DIV_MASK, GMAC_PLLCLK_DIV_NUM(div));
> > > +
> > > + regmap_update_bits(dwmac->apb_regmap, GMAC_PLLCLK_DIV,
> > > + GMAC_PLLCLK_DIV_EN, GMAC_PLLCLK_DIV_EN);
> > > + break;
> > > + default:
> > > + dev_err(dwmac->dev, "unsupported phy interface %d\n",
> > > + plat->interface);
> > > + return;
> > > + }
> > > +}
> > > +
> > > +static int thead_dwmac_enable_clk(struct plat_stmmacenet_data *plat)
> > > +{
> > > + struct thead_dwmac *dwmac = plat->bsp_priv;
> > > + u32 reg;
> > > +
> > > + switch (plat->interface) {
> > > + case PHY_INTERFACE_MODE_MII:
> > > + reg = GMAC_RX_CLK_EN | GMAC_TX_CLK_EN;
> > > + break;
> > > +
> > > + case PHY_INTERFACE_MODE_RGMII:
> > > + case PHY_INTERFACE_MODE_RGMII_ID:
> > > + case PHY_INTERFACE_MODE_RGMII_RXID:
> > > + case PHY_INTERFACE_MODE_RGMII_TXID:
> > > + /* use pll */
> > > + regmap_write(dwmac->apb_regmap, GMAC_GTXCLK_SEL, GMAC_GTXCLK_SEL_PLL);
> > > +
> > > + reg = GMAC_TX_CLK_EN | GMAC_TX_CLK_N_EN | GMAC_TX_CLK_OUT_EN |
> > > + GMAC_RX_CLK_EN | GMAC_RX_CLK_N_EN;
> > > + break;
> > > +
> > > + default:
> > > + dev_err(dwmac->dev, "unsupported phy interface %d\n",
> > > + plat->interface);
> > > + return -EINVAL;
> > > + }
> > > +
> > > + regmap_write(dwmac->apb_regmap, GMAC_CLK_EN, reg);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int thead_dwmac_init(struct platform_device *pdev,
> > > + struct plat_stmmacenet_data *plat)
> > > +{
> > > + struct thead_dwmac *dwmac = plat->bsp_priv;
> > > + int ret;
> > > +
> > > + ret = thead_dwmac_set_phy_if(plat);
> > > + if (ret)
> > > + return ret;
> > > +
> > > + ret = thead_dwmac_set_txclk_dir(plat);
> > > + if (ret)
> > > + return ret;
> > > +
> >
> > > + regmap_write(dwmac->apb_regmap, GMAC_RXCLK_DELAY_CTRL,
> > > + GMAC_RXCLK_DELAY_VAL(dwmac->rx_delay));
> > > + regmap_write(dwmac->apb_regmap, GMAC_TXCLK_DELAY_CTRL,
> > > + GMAC_TXCLK_DELAY_VAL(dwmac->tx_delay));
> >
> > Just noticed. This doesn't look right because:
> > 1. Are you sure your hardware expects the delays being specified in
> > picoseconds. It's most likely a number of reference clock cycles and
> > thus the DT-properties values should be properly converted.
>
> Good catch! I need to check further.
> > 2. Both delays should be added only for "rgmii" phy-mode, Tx clock
> > delay - for "rgmii-rxid" phy-mode, Rx clock delay - for "rgmii-txid"
> > phy-mode.
>
> For MII, the rxc/txc is provided by phy, so setting those delays
> won't impact MII.
I am talking about _RGMII_ in this case which based on the
thead_dwmac_set_phy_if() method is supported by this controller.
rgmii{-(tx|rx)id} modes are provided so to prevent both MAC and PHY
adding the delays in the RGMII interface. Imagine you have a PHY with
the fixed delays meanwhile you have them also added in the MAC. You
may and likely will end up with the traffic loss then.
As a reference take a closer look at for instance rk_gmac_powerup()
method implemented in the dwmac-rk.c driver.
-Serge(y)
> >
> > -Serge(y)
> >
> > > +
> > > + thead_dwmac_fix_speed(dwmac, SPEED_1000, 0);
> > > +
> > > + return thead_dwmac_enable_clk(plat);
> > > +}
> > > +
> > > +static int thead_dwmac_probe(struct platform_device *pdev)
> > > +{
> > > + struct plat_stmmacenet_data *plat;
> > > + struct stmmac_resources stmmac_res;
> > > + struct thead_dwmac *dwmac;
> > > + struct device_node *np = pdev->dev.of_node;
> > > + u32 delay_ps;
> > > + int ret;
> > > +
> > > + ret = stmmac_get_platform_resources(pdev, &stmmac_res);
> > > + if (ret)
> > > + return dev_err_probe(&pdev->dev, ret,
> > > + "failed to get resources\n");
> > > +
> > > + plat = stmmac_probe_config_dt(pdev, stmmac_res.mac);
> > > + if (IS_ERR(plat))
> > > + return dev_err_probe(&pdev->dev, PTR_ERR(plat),
> > > + "dt configuration failed\n");
> > > +
> > > + dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
> > > + if (!dwmac) {
> > > + ret = -ENOMEM;
> > > + goto err_remove_config_dt;
> > > + }
> > > +
> > > + if (!of_property_read_u32(np, "rx-internal-delay-ps", &delay_ps))
> > > + dwmac->rx_delay = delay_ps;
> > > + if (!of_property_read_u32(np, "tx-internal-delay-ps", &delay_ps))
> > > + dwmac->tx_delay = delay_ps;
> > > +
> > > + dwmac->apb_regmap = syscon_regmap_lookup_by_phandle(np, "thead,gmacapb");
> > > + if (IS_ERR(dwmac->apb_regmap)) {
> > > + ret = dev_err_probe(&pdev->dev, PTR_ERR(dwmac->apb_regmap),
> > > + "Failed to get gmac apb syscon\n");
> > > + goto err_remove_config_dt;
> > > + }
> > > +
> > > + dwmac->dev = &pdev->dev;
> > > + dwmac->plat = plat;
> > > + plat->bsp_priv = dwmac;
> > > + plat->fix_mac_speed = thead_dwmac_fix_speed;
> > > +
> > > + ret = thead_dwmac_init(pdev, plat);
> > > + if (ret)
> > > + goto err_remove_config_dt;
> > > +
> > > + ret = stmmac_dvr_probe(&pdev->dev, plat, &stmmac_res);
> > > + if (ret)
> > > + goto err_remove_config_dt;
> > > +
> > > + return 0;
> > > +
> > > +err_remove_config_dt:
> > > + stmmac_remove_config_dt(pdev, plat);
> > > +
> > > + return ret;
> > > +}
> > > +
> > > +static const struct of_device_id thead_dwmac_match[] = {
> > > + { .compatible = "thead,th1520-dwmac" },
> > > + { }
> > > +};
> > > +MODULE_DEVICE_TABLE(of, thead_dwmac_match);
> > > +
> > > +static struct platform_driver thead_dwmac_driver = {
> > > + .probe = thead_dwmac_probe,
> > > + .remove_new = stmmac_pltfr_remove,
> > > + .driver = {
> > > + .name = "thead-dwmac",
> > > + .pm = &stmmac_pltfr_pm_ops,
> > > + .of_match_table = thead_dwmac_match,
> > > + },
> > > +};
> > > +module_platform_driver(thead_dwmac_driver);
> > > +
> > > +MODULE_AUTHOR("T-HEAD");
> > > +MODULE_AUTHOR("Jisheng Zhang <jszhang@...nel.org>");
> > > +MODULE_DESCRIPTION("T-HEAD dwmac platform driver");
> > > +MODULE_LICENSE("GPL");
> > > --
> > > 2.40.1
> > >
> > >
Powered by blists - more mailing lists