| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Thu, 31 Aug 2023 00:44:45 +0530
From: Naresh Solanki <naresh.solanki@...ements.com>
To: Guenter Roeck <linux@...ck-us.net>
Cc: Liam Girdwood <lgirdwood@...il.com>,
Mark Brown <broonie@...nel.org>,
Jean Delvare <jdelvare@...e.com>, zev@...ilderbeest.net,
linux-kernel@...r.kernel.org, linux-hwmon@...r.kernel.org
Subject: Re: [PATCH] regulator (max5970): Add hwmon support
Hi
On Wed, 30 Aug 2023 at 21:26, Guenter Roeck <linux@...ck-us.net> wrote:
>
> On 8/30/23 04:13, Naresh Solanki wrote:
> > Utilize the integrated 10-bit ADC in Max5970/Max5978 to enable voltage
> > and current monitoring. This feature is seamlessly integrated through
> > the hwmon subsystem.
> >
> > Signed-off-by: Naresh Solanki <Naresh.Solanki@...ements.com>
> > ---
> > drivers/regulator/max5970-regulator.c | 119 ++++++++++++++++++++++++++
> > 1 file changed, 119 insertions(+)
> >
> > diff --git a/drivers/regulator/max5970-regulator.c b/drivers/regulator/max5970-regulator.c
> > index b56a174cde3d..3a6f7c293526 100644
> > --- a/drivers/regulator/max5970-regulator.c
> > +++ b/drivers/regulator/max5970-regulator.c
> > @@ -10,6 +10,7 @@
> > #include <linux/bitops.h>
> > #include <linux/device.h>
> > #include <linux/err.h>
> > +#include <linux/hwmon.h>
> > #include <linux/module.h>
> > #include <linux/io.h>
> > #include <linux/of.h>
> > @@ -32,6 +33,116 @@ enum max597x_regulator_id {
> > MAX597X_SW1,
> > };
> >
> > +static int max5970_read_adc(struct regmap *regmap, int reg, long *val)
> > +{
> > + u8 reg_data[2];
> > + int ret;
> > +
> > + ret = regmap_bulk_read(regmap, reg, ®_data[0], 2);
> > + if (ret < 0)
> > + return ret;
> > +
> > + *val = (reg_data[0] << 2) | (reg_data[1] & 3);
> > +
> > + return 0;
> > +}
> > +
> > +static int max5970_read(struct device *dev, enum hwmon_sensor_types type,
> > + u32 attr, int channel, long *val)
> > +{
> > + struct max5970_data *ddata = dev_get_drvdata(dev);
> > + struct regmap *regmap = dev_get_regmap(dev->parent, NULL);
> > + int ret;
> > +
> > + switch (type) {
> > + case hwmon_curr:
> > + switch (attr) {
> > + case hwmon_curr_input:
> > + ret = max5970_read_adc(regmap, MAX5970_REG_CURRENT_H(channel), val);
> > + /*
> > + * Calculate current from ADC value, IRNG range & shunt resistor value.
> > + * ddata->irng holds the voltage corresponding to the maximum value the
> > + * 10-bit ADC can measure.
> > + * To obtain the output, multiply the ADC value by the IRNG range (in
> > + * millivolts) and then divide it by the maximum value of the 10-bit ADC.
> > + */
> > + *val = (*val * ddata->irng[channel]) >> 10;
> > + /* Convert the voltage meansurement across shunt resistor to current */
> > + *val = (*val * 1000) / ddata->shunt_micro_ohms[channel];
> > + return ret;
> > + default:
> > + return -EOPNOTSUPP;
> > + }
> > +
> > + case hwmon_in:
> > + switch (attr) {
> > + case hwmon_in_input:
> > + ret = max5970_read_adc(regmap, MAX5970_REG_VOLTAGE_H(channel), val);
> > + /*
> > + * Calculate voltage from ADC value and MON range.
> > + * ddata->mon_rng holds the voltage corresponding to the maximum value the
> > + * 10-bit ADC can measure.
> > + * To obtain the output, multiply the ADC value by the MON range (in
> > + * microvolts) and then divide it by the maximum value of the 10-bit ADC.
> > + */
> > + *val = mul_u64_u32_shr(*val, ddata->mon_rng[channel], 10);
>
> Why do you use mul_u64_u32_shr() here but a direct shift above ?
There is possibility of overflow due to large value of ddata->mon_rng
>
> > + /* uV to mV */
> > + *val = *val / 1000;
> > + return ret;
> > + default:
> > + return -EOPNOTSUPP;
> > + }
> > + default:
> > + return -EOPNOTSUPP;
> > + }
> > +}
> > +
> > +static umode_t max5970_is_visible(const void *data,
> > + enum hwmon_sensor_types type,
> > + u32 attr, int channel)
> > +{
> > + struct max5970_data *ddata = (struct max5970_data *)data;
> > +
> > + if (channel >= ddata->num_switches)
> > + return 0;
> > +
> > + switch (type) {
> > + case hwmon_in:
> > + switch (attr) {
> > + case hwmon_in_input:
> > + return 0444;
>
> default:
> break;
Ack
>
> > + }
> > + break;
> > + case hwmon_curr:
> > + switch (attr) {
> > + case hwmon_curr_input:
> > + /* Current measurement requires knowledge of the shunt resistor value. */
> > + if (ddata->shunt_micro_ohms[channel])
> > + return 0444;
> default:
> break;
Ack
>
> > + }
> > + break;
> > + default:
> > + break;
> > + }
> > + return 0;
> > +}
> > +
> > +static const struct hwmon_ops max5970_hwmon_ops = {
> > + .is_visible = max5970_is_visible,
> > + .read = max5970_read,
> > +};
> > +
> > +static const struct hwmon_channel_info *max5970_info[] = {
> > + HWMON_CHANNEL_INFO(in, HWMON_I_INPUT, HWMON_I_INPUT),
> > + HWMON_CHANNEL_INFO(curr, HWMON_C_INPUT, HWMON_C_INPUT),
>
> Your call, but the chip does support limit and status registers, so you
> could add reporting those as well since you are at it, possibly even including
> notifications.
Will consider separate set of patch for this.
>
> > + NULL
> > +};
> > +
> > +static const struct hwmon_chip_info max5970_chip_info = {
> > + .ops = &max5970_hwmon_ops,
> > + .info = max5970_info,
> > +};
> > +
> > static int max597x_uvp_ovp_check_mode(struct regulator_dev *rdev, int severity)
> > {
> > int ret, reg;
> > @@ -432,6 +543,7 @@ static int max597x_regulator_probe(struct platform_device *pdev)
> > struct regulator_config config = { };
> > struct regulator_dev *rdev;
> > struct regulator_dev *rdevs[MAX5970_NUM_SWITCHES];
> > + struct device *hwmon_dev;
> > int num_switches;
> > int ret, i;
> >
> > @@ -485,6 +597,13 @@ static int max597x_regulator_probe(struct platform_device *pdev)
> > max597x->shunt_micro_ohms[i] = data->shunt_micro_ohms;
> > }
> >
> > + hwmon_dev = devm_hwmon_device_register_with_info(&i2c->dev, "max5970_hwmon", max597x,
> > + &max5970_chip_info, NULL);
>
> This makes the driver dependent on hwmon, so you either need a strict
> depends on HWMON
> in Kconfig, or
> depends on HWMON || HWMON=n
> and add #if IS_ENABLED(CONFIG_HWMON) as appropriate into the code.
Sure, will update accordingly. Thanks
>
>
> > + if (IS_ERR(hwmon_dev)) {
> > + return dev_err_probe(&i2c->dev, PTR_ERR(hwmon_dev), \
> > + "Unable to register hwmon device\n");
> > + }
> > +
> > if (i2c->irq) {
> > ret =
> > max597x_setup_irq(&i2c->dev, i2c->irq, rdevs, num_switches,
> >
> > base-commit: 35d0d2350d774fecf596cfb2fb050559fe5e1850
>
Powered by blists - more mailing lists