lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <09931a97-df62-9803-967f-df6135dc3be7@ti.com>
Date:   Wed, 13 Sep 2023 12:14:05 +0530
From:   MD Danish Anwar <danishanwar@...com>
To:     Roger Quadros <rogerq@...nel.org>, Andrew Lunn <andrew@...n.ch>
CC:     Simon Horman <horms@...nel.org>,
        Vignesh Raghavendra <vigneshr@...com>,
        Jacob Keller <jacob.e.keller@...el.com>,
        Richard Cochran <richardcochran@...il.com>,
        Paolo Abeni <pabeni@...hat.com>,
        Jakub Kicinski <kuba@...nel.org>,
        Eric Dumazet <edumazet@...gle.com>,
        "David S. Miller" <davem@...emloft.net>,
        <linux-kernel@...r.kernel.org>, <netdev@...r.kernel.org>,
        <srk@...com>, <r-gunasekaran@...com>, Pekka Varis <p-varis@...com>
Subject: Re: [RFC PATCH net-next 3/4] net: ti: icssg-prueth: Add support for
 ICSSG switch firmware on AM654 PG2.0 EVM

Hi Roger / Andrew,

On 08/09/23 13:47, MD Danish Anwar wrote:
> On 08/09/23 13:16, Roger Quadros wrote:
>>
>>
>> On 05/09/2023 11:43, MD Danish Anwar wrote:
>>> On 04/09/23 19:38, Andrew Lunn wrote:
>>>>> Switch mode requires loading of new firmware into ICSSG cores. This
>>>>> means interfaces have to taken down and then reconfigured to switch mode
>>>>> using devlink.
>>>>
>>>> Can you always run it in switch mode, just not have the ports in a
>>>> bridge?
>>>>
>>>> 	Andrew
>>>
>>> No, we can't always run it in switch mode. Switch mode requires loading
>>> of different firmware. The switch firmware only supports switch
>>> operations. If the ports are not in a bridge in switch mode, the normal
>>> functionalities will not work. We will not be able to send / receive /
>>> forward packets in switch mode without bridge.
>>>
>>> When device is booted up, the dual EMAC firmware is loaded and ICSSG
>>> works in dual EMAC mode with both ports doing independent TX / RX.
>>>
>>> When switch mode is enabled, dual EMAC firmware is unloaded and switch
>>> firmware is loaded. The ports become part of the bridge and the two port
>>> together acts as a switch.
>>>
>>
>> Since we are loading the switch firmware and the switch logic is in firmware,
>> it means we don't really need Linux help to do basic switching on the external
>> ports.
>>
>> I suppose Andrews question was, can it work as a switch after switching
>> from dual-emac to switch mode and not setting up the Linux bridge.
>>
> 
> I did some further testing on switch mode. The basic functionality would
> work without a bridge as well. This will need one modification in driver
> but even without bridge switching will work.
> 
> When enabling switch mode the driver sets the HOST_MAC_ADDR to the
> bridge's addr. If bridge is not there, this will result in KERNEL NULL
> POINTER crash.
> 
> icssg_class_set_host_mac_addr(prueth->miig_rt,
> prueth->hw_bridge_dev->dev_addr);
> 
> However if we change this to only set when bridge is there, it works
> 
> if (prueth->hw_bridge_dev)
> 	icssg_class_set_host_mac_addr(prueth->miig_rt,
> prueth->hw_bridge_dev->dev_addr);
> 
> With this change forwarding works in switch mode without setting up the
> bridge. Just loading the switch firmware is enough.
> 
> 
>> e.g. Looking at your command list
>>
>>> Switch to ICSSG Switch mode:
>>>  ip link set dev eth1 down
>>>  ip link set dev eth2 down
>>>  devlink dev param set platform/icssg2-eth name \
>>>  switch_mode value 1 cmode runtime
>>
>> At this point, can it work as a switch. If not, why?>
> 
> To summarize, yes it can work at this point.
> 

As discussed on this thread, switching operation can work with the ICSSG
switch firmware, without creating bridge. However without bridge only
forwarding works. If we want the switch to consume packets bridge is
required.

ICSSG switch firmware without bridge
  - Forwarding works but packets can not be consumed by switch.

ICSSG switch firmware without bridge
  - Forwarding works and packets can be consumed by switch.

In order to consume the packets, creating a bridge is required.

I will keep the commands in commit message as it is. Please let me know
if this is OK to you or if any change is required.

>>>  ip link add name br0 type bridge
>>>  ip link set dev eth1 master br0
>>>  ip link set dev eth2 master br0
>>>  ip link set dev br0 up
>>>  ip link set dev eth1 up
>>>  ip link set dev eth2 up
>>>  bridge vlan add dev br0 vid 1 pvid untagged self
>>
> 

-- 
Thanks and Regards,
Danish

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ