[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20231001-pxa-gpio-v4-5-0f3b975e6ed5@skole.hr>
Date: Sun, 01 Oct 2023 16:12:56 +0200
From: Duje Mihanović <duje.mihanovic@...le.hr>
To: Daniel Mack <daniel@...que.org>,
Haojian Zhuang <haojian.zhuang@...il.com>,
Robert Jarzmik <robert.jarzmik@...e.fr>,
Russell King <linux@...linux.org.uk>,
Alan Stern <stern@...land.harvard.edu>,
Greg Kroah-Hartman <gregkh@...uxfoundation.org>,
Linus Walleij <linus.walleij@...aro.org>,
Bartosz Golaszewski <brgl@...ev.pl>,
Andy Shevchenko <andy@...nel.org>,
Dmitry Torokhov <dmitry.torokhov@...il.com>,
Mark Brown <broonie@...nel.org>
Cc: linux-arm-kernel@...ts.infradead.org, linux-kernel@...r.kernel.org,
linux-usb@...r.kernel.org, linux-gpio@...r.kernel.org,
linux-input@...r.kernel.org, linux-spi@...r.kernel.org,
Duje Mihanović <duje.mihanovic@...le.hr>
Subject: [PATCH RFC v4 5/6] ARM: pxa: Convert gumstix Bluetooth to GPIO
descriptors
Gumstix still uses the legacy GPIO interface for resetting the Bluetooth
device.
Convert it to use the GPIO descriptor interface.
Reviewed-by: Linus Walleij <linus.walleij@...aro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@...le.hr>
---
arch/arm/mach-pxa/gumstix.c | 24 +++++++++++++-----------
1 file changed, 13 insertions(+), 11 deletions(-)
diff --git a/arch/arm/mach-pxa/gumstix.c b/arch/arm/mach-pxa/gumstix.c
index c9f0f62187bd..14e1b9274d7a 100644
--- a/arch/arm/mach-pxa/gumstix.c
+++ b/arch/arm/mach-pxa/gumstix.c
@@ -20,8 +20,8 @@
#include <linux/delay.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
+#include <linux/gpio/consumer.h>
#include <linux/gpio/machine.h>
-#include <linux/gpio.h>
#include <linux/err.h>
#include <linux/clk.h>
@@ -129,6 +129,9 @@ static void gumstix_udc_init(void)
#endif
#ifdef CONFIG_BT
+GPIO_LOOKUP_SINGLE(gumstix_bt_gpio_table, "pxa2xx-uart.1", "pxa-gpio",
+ GPIO_GUMSTIX_BTRESET, "BTRST", GPIO_ACTIVE_LOW);
+
/* Normally, the bootloader would have enabled this 32kHz clock but many
** boards still have u-boot 1.1.4 so we check if it has been turned on and
** if not, we turn it on with a warning message. */
@@ -153,24 +156,23 @@ static void gumstix_setup_bt_clock(void)
static void __init gumstix_bluetooth_init(void)
{
- int err;
+ struct gpio_desc *desc;
+
+ gpiod_add_lookup_table(&gumstix_bt_gpio_table);
gumstix_setup_bt_clock();
- err = gpio_request(GPIO_GUMSTIX_BTRESET, "BTRST");
- if (err) {
+ desc = gpiod_get(&pxa_device_btuart.dev, "BTRST", GPIOD_OUT_HIGH);
+ if (IS_ERR(desc)) {
pr_err("gumstix: failed request gpio for bluetooth reset\n");
return;
}
- err = gpio_direction_output(GPIO_GUMSTIX_BTRESET, 1);
- if (err) {
- pr_err("gumstix: can't reset bluetooth\n");
- return;
- }
- gpio_set_value(GPIO_GUMSTIX_BTRESET, 0);
+ gpiod_set_value(desc, 0);
udelay(100);
- gpio_set_value(GPIO_GUMSTIX_BTRESET, 1);
+ gpiod_set_value(desc, 1);
+
+ gpiod_put(desc);
}
#else
static void gumstix_bluetooth_init(void)
--
2.42.0
Powered by blists - more mailing lists