lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20231003-msm8916-modem-v2-11-61b684be55c0@gerhold.net>
Date:   Tue, 03 Oct 2023 15:18:29 +0200
From:   Stephan Gerhold <stephan@...hold.net>
To:     Bjorn Andersson <andersson@...nel.org>
Cc:     Andy Gross <agross@...nel.org>,
        Konrad Dybcio <konrad.dybcio@...aro.org>,
        linux-arm-msm@...r.kernel.org, devicetree@...r.kernel.org,
        linux-kernel@...r.kernel.org, phone-devel@...r.kernel.org,
        ~postmarketos/upstreaming@...ts.sr.ht,
        Bryan O'Donoghue <bryan.odonoghue@...aro.org>,
        Stephan Gerhold <stephan@...hold.net>,
        Jonathan Albrieux <jonathan.albrieux@...il.com>
Subject: [PATCH v2 11/14] arm64: dts: qcom: msm8916-longcheer-l8910: Add
 sound and modem

From: Jonathan Albrieux <jonathan.albrieux@...il.com>

Enable sound and modem for the Longcheer L8910 (BQ Aquaris X5).
The setup is similar to most MSM8916 devices, i.e.:

 - QDSP6 audio
 - Earpiece/headphones/microphones via digital/analog codec in
   MSM8916/PM8916
 - Audio jack detection via analog codec in PM8916
 - WWAN Internet via BAM-DMUX

except:

 - Awinic AW8738 connected to HPH_R (headphones) output of the analog
   codec. Note that unlike for wingtech-wt88047 there is no analog
   switch that would allow disabling output via the headphone jack
   when the speaker is enabled.

Signed-off-by: Jonathan Albrieux <jonathan.albrieux@...il.com>
Co-developed-by: Stephan Gerhold <stephan@...hold.net>
Reviewed-by: Konrad Dybcio <konrad.dybcio@...aro.org>
Signed-off-by: Stephan Gerhold <stephan@...hold.net>
---
 .../boot/dts/qcom/msm8916-longcheer-l8910.dts      | 52 ++++++++++++++++++++++
 1 file changed, 52 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
index 41cadb906b98..e64bf687ca7d 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
@@ -3,6 +3,8 @@
 /dts-v1/;
 
 #include "msm8916-pm8916.dtsi"
+#include "msm8916-modem-qdsp6.dtsi"
+
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
@@ -22,6 +24,16 @@ chosen {
 		stdout-path = "serial0";
 	};
 
+	speaker_amp: audio-amplifier {
+		compatible = "awinic,aw8738";
+		mode-gpios = <&tlmm 114 GPIO_ACTIVE_HIGH>;
+		awinic,mode = <5>;
+		sound-name-prefix = "Speaker Amp";
+
+		pinctrl-0 = <&spk_ext_pa_default>;
+		pinctrl-names = "default";
+	};
+
 	flash-led-controller {
 		compatible = "ocs,ocp8110";
 		enable-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>;
@@ -107,6 +119,17 @@ &blsp_uart2 {
 	status = "okay";
 };
 
+&mpss_mem {
+	reg = <0x0 0x86800000 0x0 0x5000000>;
+};
+
+&pm8916_codec {
+	qcom,micbias-lvl = <2800>;
+	qcom,mbhc-vthreshold-low = <75 100 120 180 500>;
+	qcom,mbhc-vthreshold-high = <75 100 120 180 500>;
+	qcom,hphl-jack-type-normally-open;
+};
+
 &pm8916_resin {
 	status = "okay";
 	linux,code = <KEY_VOLUMEDOWN>;
@@ -137,6 +160,28 @@ &sdhc_2 {
 	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 };
 
+&sound {
+	/*
+	 * Provide widgets/pin-switches to allow enabling speaker separately.
+	 * The hardware does not provide a way to disable the output via the
+	 * headphone jack when the speaker is enabled.
+	 */
+	model = "bq-paella";
+	widgets =
+		"Speaker", "Speaker",
+		"Headphone", "Headphones";
+	pin-switches = "Speaker";
+	audio-routing =
+		"Speaker", "Speaker Amp OUT",
+		"Speaker Amp IN", "HPH_R",
+		"Headphones", "HPH_L",
+		"Headphones", "HPH_R",
+		"AMIC1", "MIC BIAS External1",
+		"AMIC2", "MIC BIAS Internal2",
+		"AMIC3", "MIC BIAS External1";
+	aux-devs = <&speaker_amp>;
+};
+
 &usb {
 	status = "okay";
 	extcon = <&usb_id>, <&usb_id>;
@@ -205,6 +250,13 @@ sdc2_cd_default: sdc2-cd-default-state {
 		bias-disable;
 	};
 
+	spk_ext_pa_default: spk-ext-pa-default-state {
+		pins = "gpio114";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	usb_id_default: usb-id-default-state {
 		pins = "gpio110";
 		function = "gpio";

-- 
2.42.0

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ