| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Date: Thu, 5 Oct 2023 19:50:25 -0500
From: David Lechner <dlechner@...libre.com>
To: linux-iio@...r.kernel.org, linux-staging@...ts.linux.dev
Cc: David Lechner <dlechner@...libre.com>,
Jonathan Cameron <jic23@...nel.org>,
Michael Hennerich <Michael.Hennerich@...log.com>,
Nuno Sá <nuno.sa@...log.com>,
Axel Haslam <ahaslam@...libre.com>,
Philip Molloy <pmolloy@...libre.com>,
linux-kernel@...r.kernel.org
Subject: [PATCH v4 08/17] staging: iio: resolver: ad2s1210: convert LOS threshold to event attr
The AD2S1210 has a programmable threshold for the loss of signal (LOS)
fault. This fault is triggered when either the sine or cosine input
falls below the threshold voltage.
This patch converts the custom device LOS threshold attribute to an
event falling edge threshold attribute on a new monitor signal channel.
The monitor signal is an internal signal that combines the amplitudes
of the sine and cosine inputs as well as the current angle and position
output. This signal is used to detect faults in the input signals.
The attribute now uses millivolts instead of the raw register value in
accordance with the IIO ABI.
Emitting the event will be implemented in a later patch.
Signed-off-by: David Lechner <dlechner@...libre.com>
---
v4 changes:
* Fixed missing static qualifier on attribute definition.
v3 changes: This is a new patch in v3
drivers/staging/iio/resolver/ad2s1210.c | 76 +++++++++++++++++++++++++++++++--
1 file changed, 72 insertions(+), 4 deletions(-)
diff --git a/drivers/staging/iio/resolver/ad2s1210.c b/drivers/staging/iio/resolver/ad2s1210.c
index 12437f697f79..d52aed30ca66 100644
--- a/drivers/staging/iio/resolver/ad2s1210.c
+++ b/drivers/staging/iio/resolver/ad2s1210.c
@@ -66,6 +66,11 @@
#define PHASE_360_DEG_TO_RAD_INT 6
#define PHASE_360_DEG_TO_RAD_MICRO 283185
+/* Threshold voltage registers have 1 LSB == 38 mV */
+#define THRESHOLD_MILLIVOLT_PER_LSB 38
+/* max voltage for threshold registers is 0x7F * 38 mV */
+#define THRESHOLD_RANGE_STR "[0 38 4826]"
+
enum ad2s1210_mode {
MOD_POS = 0b00,
MOD_VEL = 0b01,
@@ -451,6 +456,38 @@ static const int ad2s1210_lot_threshold_urad_per_lsb[] = {
1237, /* 16-bit: same as 14-bit */
};
+static int ad2s1210_get_voltage_threshold(struct ad2s1210_state *st,
+ unsigned int reg, int *val)
+{
+ unsigned int reg_val;
+ int ret;
+
+ mutex_lock(&st->lock);
+ ret = regmap_read(st->regmap, reg, ®_val);
+ mutex_unlock(&st->lock);
+
+ if (ret < 0)
+ return ret;
+
+ *val = reg_val * THRESHOLD_MILLIVOLT_PER_LSB;
+ return IIO_VAL_INT;
+}
+
+static int ad2s1210_set_voltage_threshold(struct ad2s1210_state *st,
+ unsigned int reg, int val)
+{
+ unsigned int reg_val;
+ int ret;
+
+ reg_val = val / THRESHOLD_MILLIVOLT_PER_LSB;
+
+ mutex_lock(&st->lock);
+ ret = regmap_write(st->regmap, reg, reg_val);
+ mutex_unlock(&st->lock);
+
+ return ret;
+}
+
static int ad2s1210_get_lot_high_threshold(struct ad2s1210_state *st,
int *val, int *val2)
{
@@ -710,9 +747,6 @@ static int ad2s1210_write_raw(struct iio_dev *indio_dev,
static IIO_DEVICE_ATTR(fault, 0644,
ad2s1210_show_fault, ad2s1210_clear_fault, 0);
-static IIO_DEVICE_ATTR(los_thrd, 0644,
- ad2s1210_show_reg, ad2s1210_store_reg,
- AD2S1210_REG_LOS_THRD);
static IIO_DEVICE_ATTR(dos_ovr_thrd, 0644,
ad2s1210_show_reg, ad2s1210_store_reg,
AD2S1210_REG_DOS_OVR_THRD);
@@ -749,6 +783,16 @@ static const struct iio_event_spec ad2s1210_phase_event_spec[] = {
},
};
+static const struct iio_event_spec ad2s1210_monitor_signal_event_spec[] = {
+ {
+ /* Sine/cosine below LOS threshold fault. */
+ .type = IIO_EV_TYPE_THRESH,
+ .dir = IIO_EV_DIR_FALLING,
+ /* Loss of signal threshold. */
+ .mask_separate = BIT(IIO_EV_INFO_VALUE),
+ },
+};
+
static const struct iio_chan_spec ad2s1210_channels[] = {
{
.type = IIO_ANGL,
@@ -807,12 +851,19 @@ static const struct iio_chan_spec ad2s1210_channels[] = {
.scan_index = -1,
.info_mask_separate = BIT(IIO_CHAN_INFO_FREQUENCY),
.info_mask_separate_available = BIT(IIO_CHAN_INFO_FREQUENCY),
+ }, {
+ /* monitor signal */
+ .type = IIO_ALTVOLTAGE,
+ .indexed = 1,
+ .channel = 0,
+ .scan_index = -1,
+ .event_spec = ad2s1210_monitor_signal_event_spec,
+ .num_event_specs = ARRAY_SIZE(ad2s1210_monitor_signal_event_spec),
},
};
static struct attribute *ad2s1210_attributes[] = {
&iio_dev_attr_fault.dev_attr.attr,
- &iio_dev_attr_los_thrd.dev_attr.attr,
&iio_dev_attr_dos_ovr_thrd.dev_attr.attr,
&iio_dev_attr_dos_mis_thrd.dev_attr.attr,
&iio_dev_attr_dos_rst_max_thrd.dev_attr.attr,
@@ -851,11 +902,14 @@ static IIO_CONST_ATTR(in_phase0_mag_rising_value_available,
__stringify(PHASE_44_DEG_TO_RAD_MICRO) " "
__stringify(PHASE_360_DEG_TO_RAD_INT) "."
__stringify(PHASE_360_DEG_TO_RAD_MICRO));
+static IIO_CONST_ATTR(in_altvoltage0_thresh_falling_value_available,
+ THRESHOLD_RANGE_STR);
static IIO_DEVICE_ATTR_RO(in_angl1_thresh_rising_value_available, 0);
static IIO_DEVICE_ATTR_RO(in_angl1_thresh_rising_hysteresis_available, 0);
static struct attribute *ad2s1210_event_attributes[] = {
&iio_const_attr_in_phase0_mag_rising_value_available.dev_attr.attr,
+ &iio_const_attr_in_altvoltage0_thresh_falling_value_available.dev_attr.attr,
&iio_dev_attr_in_angl1_thresh_rising_value_available.dev_attr.attr,
&iio_dev_attr_in_angl1_thresh_rising_hysteresis_available.dev_attr.attr,
NULL,
@@ -908,6 +962,13 @@ static int ad2s1210_read_event_value(struct iio_dev *indio_dev,
default:
return -EINVAL;
}
+ case IIO_ALTVOLTAGE:
+ if (chan->output)
+ return -EINVAL;
+ if (type == IIO_EV_TYPE_THRESH && dir == IIO_EV_DIR_FALLING)
+ return ad2s1210_get_voltage_threshold(st,
+ AD2S1210_REG_LOS_THRD, val);
+ return -EINVAL;
case IIO_PHASE:
return ad2s1210_get_phase_lock_range(st, val, val2);
default:
@@ -934,6 +995,13 @@ static int ad2s1210_write_event_value(struct iio_dev *indio_dev,
default:
return -EINVAL;
}
+ case IIO_ALTVOLTAGE:
+ if (chan->output)
+ return -EINVAL;
+ if (type == IIO_EV_TYPE_THRESH && dir == IIO_EV_DIR_FALLING)
+ return ad2s1210_set_voltage_threshold(st,
+ AD2S1210_REG_LOS_THRD, val);
+ return -EINVAL;
case IIO_PHASE:
return ad2s1210_set_phase_lock_range(st, val, val2);
default:
--
2.42.0
Powered by blists - more mailing lists