lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-ID: <20231008130515.1155664-5-megi@xff.cz>
Date:   Sun,  8 Oct 2023 15:05:02 +0200
From:   Ondřej Jirman <megi@....cz>
To:     Rob Herring <robh+dt@...nel.org>,
        Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
        Conor Dooley <conor+dt@...nel.org>,
        Heiko Stuebner <heiko@...ech.de>
Cc:     Ondrej Jirman <megi@....cz>, Jagan Teki <jagan@...eble.ai>,
        Jonas Karlman <jonas@...boo.se>,
        Chris Morgan <macromorgan@...mail.com>,
        Sebastian Reichel <sebastian.reichel@...labora.com>,
        devicetree@...r.kernel.org, linux-arm-kernel@...ts.infradead.org,
        linux-rockchip@...ts.infradead.org, linux-kernel@...r.kernel.org
Subject: [PATCH 4/4] arm64: dts: rk3588-orangepi-5-plus: Add board device tree

From: Ondrej Jirman <megi@....cz>

Orange Pi 5 Plus is RK3588 based SBC featuring:

- 2x 2.5G ethernet ports – onboard NIC hooked to PCIe 2.0 interface
- 2x USB 2.0 host ports
- 2x USB 3.0 host ports (exposed over USB 3.0 hub)
- Type-C port featuring USB 2.0/3.0 and Alt-DP mode
- PCIe 2.0/USB 2.0/I2S/I2C/UART on E.KEY socket
- RTC
- ES8388 on-board sound codec – jack in/out, onboard mic, speaker amplifier
- SPI NOR flash
- RGB LED (R is always on)
- IR receiver
- PCIe 3.0 on the bottom for NVMe, etc.
- 40pin GPIO header (with gpio, I2C, SPI, PWM, UART)
- Power, recovery and Mask ROM buttons
- 2x HDMI out, 1x HDMI in
- Slots/connectors for eMMC, uSD card, fan, MIPI CSI/DSI

Signed-off-by: Ondrej Jirman <megi@....cz>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../dts/rockchip/rk3588-orangepi-5-plus.dts   | 857 ++++++++++++++++++
 2 files changed, 858 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index e7728007fd1b..7f340e2a4875 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -101,6 +101,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-io.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6b-io.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-evb1-v10.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-nanopc-t6.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-orangepi-5-plus.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-rock-5b.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-indiedroid-nova.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-khadas-edge2.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts b/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts
new file mode 100644
index 000000000000..b74c4f96c60a
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-plus.dts
@@ -0,0 +1,857 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2023 Ondřej Jirman <megi@....cz>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/usb/pd.h>
+#include "rk3588.dtsi"
+
+/ {
+	model = "Xunlong Orange Pi 5 Plus";
+	compatible = "xunlong,orangepi-5-plus", "rockchip,rk3588";
+
+	aliases {
+		mmc0 = &sdhci;
+		mmc1 = &sdmmc;
+		serial2 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	adc-keys-0 {
+		compatible = "adc-keys";
+		io-channels = <&saradc 0>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+		poll-interval = <100>;
+
+		button-maskrom {
+			linux,code = <KEY_SETUP>;
+			label = "Mask Rom";
+			press-threshold-microvolt = <2000>;
+		};
+	};
+
+	adc-keys-1 {
+		compatible = "adc-keys";
+		io-channels = <&saradc 1>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+		poll-interval = <100>;
+
+		button-recovery {
+			linux,code = <KEY_VENDOR>;
+			label = "Recovery";
+			press-threshold-microvolt = <2000>;
+		};
+	};
+
+	speaker_amp: speaker-audio-amplifier {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_HIGH>;
+		sound-name-prefix = "Speaker Amp";
+	};
+
+	headphone_amp: headphones-audio-amplifier {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&gpio3 RK_PA7 GPIO_ACTIVE_HIGH>;
+		sound-name-prefix = "Headphones Amp";
+	};
+
+	ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ir_receiver_pin>;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&blue_led_pin>;
+
+		led {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <1>;
+			gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	fan: pwm-fan {
+		compatible = "pwm-fan";
+		cooling-levels = <0 70 75 80 100>;
+		fan-supply = <&vcc5v0_sys>;
+		pwms = <&pwm3 0 50000 0>;
+		#cooling-cells = <2>;
+	};
+
+	pwm-leds {
+		compatible = "pwm-leds";
+
+		led {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <2>;
+			max-brightness = <255>;
+			pwms = <&pwm2 0 25000 0>;
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hp_detect>;
+		simple-audio-card,name = "Analog";
+		simple-audio-card,aux-devs = <&speaker_amp>, <&headphone_amp>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,mclk-fs = <256>;
+		simple-audio-card,hp-det-gpio = <&gpio1 RK_PD3 GPIO_ACTIVE_LOW>;
+		simple-audio-card,bitclock-master = <&daicpu>;
+		simple-audio-card,frame-master = <&daicpu>;
+		/*TODO: SARADC_IN3 is used as MIC detection / key input */
+
+		simple-audio-card,widgets =
+			"Microphone", "Onboard Microphone",
+			"Microphone", "Microphone Jack",
+			"Speaker", "Speaker",
+			"Headphone", "Headphones";
+
+		simple-audio-card,routing =
+			"Headphones", "LOUT1",
+			"Headphones", "ROUT1",
+			"Speaker", "LOUT2",
+			"Speaker", "ROUT2",
+
+			"Headphones", "Headphones Amp OUTL",
+			"Headphones", "Headphones Amp OUTR",
+			"Headphones Amp INL", "LOUT1",
+			"Headphones Amp INR", "ROUT1",
+
+			"Speaker", "Speaker Amp OUTL",
+			"Speaker", "Speaker Amp OUTR",
+			"Speaker Amp INL", "LOUT2",
+			"Speaker Amp INR", "ROUT2",
+
+			/* single ended signal to LINPUT1 */
+			"LINPUT1", "Microphone Jack",
+			"RINPUT1", "Microphone Jack",
+			/* differential signal */
+			"LINPUT2", "Onboard Microphone",
+			"RINPUT2", "Onboard Microphone";
+
+		daicpu: simple-audio-card,cpu {
+			sound-dai = <&i2s0_8ch>;
+			system-clock-frequency = <12288000>;
+		};
+
+		daicodec: simple-audio-card,codec {
+			sound-dai = <&es8388>;
+			system-clock-frequency = <12288000>;
+		};
+	};
+
+	vcc3v3_pcie30: vcc3v3-pcie30-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_pcie30";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpios = <&gpio2 RK_PB6 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc3v3_pcie_eth: vcc3v3-pcie-eth-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_pcie_eth";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio3 RK_PB4 GPIO_ACTIVE_LOW>;
+		startup-delay-us = <50000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc3v3_wf: vcc3v3-wf-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_wf";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpios = <&gpio2 RK_PC5 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <50000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vcc5v0_usb20: vcc5v0-usb20-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb20";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb20_en>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&combphy0_ps {
+	status = "okay";
+};
+
+&combphy1_ps {
+	status = "okay";
+};
+
+&combphy2_psu {
+	status = "okay";
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_big0_s0>;
+	mem-supply = <&vdd_cpu_big0_mem_s0>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_big0_s0>;
+	mem-supply = <&vdd_cpu_big0_mem_s0>;
+};
+
+&cpu_b2 {
+	cpu-supply = <&vdd_cpu_big1_s0>;
+	mem-supply = <&vdd_cpu_big1_mem_s0>;
+};
+
+&cpu_b3 {
+	cpu-supply = <&vdd_cpu_big1_s0>;
+	mem-supply = <&vdd_cpu_big1_mem_s0>;
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+	mem-supply = <&vdd_cpu_lit_mem_s0>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+	mem-supply = <&vdd_cpu_lit_mem_s0>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+	mem-supply = <&vdd_cpu_lit_mem_s0>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+	mem-supply = <&vdd_cpu_lit_mem_s0>;
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0m2_xfer>;
+	status = "okay";
+
+	vdd_cpu_big0_s0: vdd_cpu_big0_mem_s0: regulator@42 {
+		compatible = "rockchip,rk8602";
+		reg = <0x42>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu_big0_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <1050000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_cpu_big1_s0: vdd_cpu_big1_mem_s0: regulator@43 {
+		compatible = "rockchip,rk8603", "rockchip,rk8602";
+		reg = <0x43>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu_big1_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <1050000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c6 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	hym8563: rtc@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-output-names = "hym8563";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hym8563_int>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
+		wakeup-source;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	/* PLDO2 vcca 1.8V, BUCK8 gated by PLDO2 being enabled */
+	es8388: audio-codec@11 {
+		compatible = "everest,es8388";
+		reg = <0x11>;
+		clocks = <&cru I2S0_8CH_MCLKOUT>;
+		clock-names = "mclk";
+		AVDD-supply = <&vcc_1v8_s0>;
+		DVDD-supply = <&vcc_1v8_s0>;
+		HPVDD-supply = <&vcc_3v3_s0>;
+		PVDD-supply = <&vcc_3v3_s0>;
+		assigned-clocks = <&cru I2S0_8CH_MCLKOUT>;
+		assigned-clock-rates = <12288000>;
+		#sound-dai-cells = <0>;
+	};
+};
+
+&i2s0_8ch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s0_lrck
+		     &i2s0_mclk
+		     &i2s0_sclk
+		     &i2s0_sdi0
+		     &i2s0_sdo0>;
+	status = "okay";
+};
+
+&i2s2_2ch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s2m0_lrck
+		     &i2s2m0_sclk
+		     &i2s2m0_sdi
+		     &i2s2m0_sdo>;
+	status = "okay";
+};
+
+/* phy1 - M.KEY socket */
+&pcie2x1l0 {
+	reset-gpios = <&gpio4 RK_PA5 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_wf>;
+	status = "okay";
+};
+
+/* phy2 - right ethernet port */
+&pcie2x1l1 {
+	reset-gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie_eth>;
+	status = "okay";
+};
+
+/* phy0 - left ethernet port */
+&pcie2x1l2 {
+	reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie_eth>;
+	status = "okay";
+};
+
+&pcie30phy {
+	status = "okay";
+};
+
+&pcie3x4 {
+	reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie30>;
+	status = "okay";
+};
+
+&pinctrl {
+	hym8563 {
+		hym8563_int: hym8563-int {
+			rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		blue_led_pin: blue-led {
+			rockchip,pins = <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	ir-receiver {
+		ir_receiver_pin: ir-receiver-pin {
+			rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sound {
+		hp_detect: hp-detect {
+			rockchip,pins = <1 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb {
+		vcc5v0_usb20_en: vcc5v0-usb20-en {
+			rockchip,pins = <3 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pwm2 {
+	status = "okay";
+	pinctrl-0 = <&pwm2m1_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm3 {
+	status = "okay";
+	pinctrl-0 = <&pwm3m1_pins>;
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vcc_1v8_s0>;
+};
+
+&sdhci {
+	bus-width = <8>;
+	no-sdio;
+	no-sd;
+	non-removable;
+	max-frequency = <200000000>;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	max-frequency = <150000000>;
+	no-sdio;
+	no-mmc;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_3v3_s3>;
+	vqmmc-supply = <&vccio_sd_s0>;
+	status = "okay";
+};
+
+&sfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&fspim1_pins>;
+	status = "okay";
+
+	spi_flash: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-max-frequency = <100000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
+	};
+};
+
+&spi2 {
+	assigned-clocks = <&cru CLK_SPI2>;
+	assigned-clock-rates = <200000000>;
+	num-cs = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
+	status = "okay";
+
+	pmic@0 {
+		compatible = "rockchip,rk806";
+		reg = <0x0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+		rockchip,system-power-controller;
+		spi-max-frequency = <1000000>;
+
+		vcc1-supply = <&vcc5v0_sys>;
+		vcc2-supply = <&vcc5v0_sys>;
+		vcc3-supply = <&vcc5v0_sys>;
+		vcc4-supply = <&vcc5v0_sys>;
+		vcc5-supply = <&vcc5v0_sys>;
+		vcc6-supply = <&vcc5v0_sys>;
+		vcc7-supply = <&vcc5v0_sys>;
+		vcc8-supply = <&vcc5v0_sys>;
+		vcc9-supply = <&vcc5v0_sys>;
+		vcc10-supply = <&vcc5v0_sys>;
+		vcc11-supply = <&vcc_2v0_pldo_s3>;
+		vcc12-supply = <&vcc5v0_sys>;
+		vcc13-supply = <&vdd2_ddr_s3>;
+		vcc14-supply = <&vdd2_ddr_s3>;
+		vcca-supply = <&vcc5v0_sys>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		rk806_dvs1_null: dvs1-null-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs2_null: dvs2-null-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs3_null: dvs3-null-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun0";
+		};
+
+		regulators {
+			vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 {
+				regulator-boot-on;
+				regulator-enable-ramp-delay = <400>;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-name = "vdd_gpu_s0";
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-name = "vdd_cpu_lit_s0";
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_log_s0: dcdc-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <675000>;
+				regulator-max-microvolt = <825000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_log_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <825000>;
+				regulator-name = "vdd_vdenc_s0";
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_ddr_s0: dcdc-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <675000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdd_ddr_s0";
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			vdd2_ddr_s3: dcdc-reg6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vdd2_ddr_s3";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_2v0_pldo_s3: dcdc-reg7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-name = "vdd_2v0_pldo_s3";
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <2000000>;
+				};
+			};
+
+			vcc_3v3_s3: dcdc-reg8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_3v3_s3";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vddq_ddr_s0: dcdc-reg9 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vddq_ddr_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8_s3: dcdc-reg10 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_1v8_s3";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			avcc_1v8_s0: pldo-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "avcc_1v8_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			/* shorted to avcc_1v8_s0 on the board */
+			vcc_1v8_s0: pldo-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_1v8_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			avdd_1v2_s0: pldo-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-name = "avdd_1v2_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3_s0: pldo-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_3v3_s0";
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd_s0: pldo-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd_s0";
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			pldo6_s3: pldo-reg6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "pldo6_s3";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_0v75_s3: nldo-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+				regulator-name = "vdd_0v75_s3";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vdd_ddr_pll_s0: nldo-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-name = "vdd_ddr_pll_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			avdd_0v75_s0: nldo-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				/*
+				 * The schematic mentions that actual setting
+				 * should be 0.8375V. RK3588 datasheet specifies
+				 * maximum as 0.825V. So we set datasheet max
+				 * here.
+				 */
+				regulator-min-microvolt = <825000>;
+				regulator-max-microvolt = <825000>;
+				regulator-name = "avdd_0v75_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_0v85_s0: nldo-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-name = "vdd_0v85_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_0v75_s0: nldo-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+				regulator-name = "vdd_0v75_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&tsadc {
+	status = "okay";
+};
+
+&u2phy2 {
+	status = "okay";
+};
+
+&u2phy3 {
+	status = "okay";
+};
+
+&u2phy2_host {
+	phy-supply = <&vcc5v0_usb20>;
+	status = "okay";
+};
+
+&u2phy3_host {
+	phy-supply = <&vcc5v0_usb20>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-0 = <&uart2m0_xfer>;
+	status = "okay";
+};
+
+&uart9 {
+	pinctrl-0 = <&uart9m0_xfer>;
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
-- 
2.42.0

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ