linux-kernel - [Patch v2 6/6] tty: serial: 8250: Add support for MOXA PCIe boards to switch interface between RS422/RS485

lists.openwall.net		lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC
Open Source and information security mailing list archives

Hash Suite: Windows password security audit tool. GUI, reports in PDF.

[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]

Message-Id: <20231016033705.20669-7-crescentcy.hsieh@moxa.com>
Date:   Mon, 16 Oct 2023 11:37:05 +0800
From:   Crescent CY Hsieh <crescentcy.hsieh@...a.com>
To:     gregkh@...uxfoundation.org, jirislaby@...nel.org
Cc:     linux-kernel@...r.kernel.org, linux-serial@...r.kernel.org,
        Crescent CY Hsieh <crescentcy.hsieh@...a.com>
Subject: [Patch v2 6/6] tty: serial: 8250: Add support for MOXA PCIe boards to switch interface between RS422/RS485

MOXA PCIe boards have 4 serial interfaces and don't require additional
stuff to switch between interfaces:

- RS232
- RS422
- RS485_2W (half-duplex)
- RS485_4W (full-duplex)

By using ioctl command "TIOCRS485", it can switch between default
interface and RS485 if supported.

That means, for RS422/RS485 board, it can switch between RS422 and
RS485 by setting the flags within struct serial_rs485.

However, for the RS232/RS422/RS485 board, it can only switch between
RS232 and RS485, there's no flag for switching interface into RS422.

This patch uses "SER_RS485_TERMINATE_BUS" to represent RS422 as a
workaround solution.

Signed-off-by: Crescent CY Hsieh <crescentcy.hsieh@...a.com>
---
 drivers/tty/serial/8250/8250_pci.c | 52 ++++++++++++++++++++++++++++++
 1 file changed, 52 insertions(+)

diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 72dd27141801..e2e8a28242bc 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1976,6 +1976,10 @@ pci_sunix_setup(struct serial_private *priv,
 #define MOXA_RS485_2W	0x0F
 #define MOXA_UIR_OFFSET	0x04
 
+static const struct serial_rs485 pci_moxa_rs485_supported = {
+	.flags = SER_RS485_ENABLED | SER_RS485_RX_DURING_TX | SER_RS485_TERMINATE_BUS,
+};
+
 static bool pci_moxa_is_mini_pcie(unsigned short device)
 {
 	if (device == PCI_DEVICE_ID_MOXA_CP102N	||
@@ -1989,6 +1993,11 @@ static bool pci_moxa_is_mini_pcie(unsigned short device)
 	return false;
 }
 
+static bool pci_moxa_match_x1xx(unsigned short device)
+{
+	return (device & 0x0F00) == 0x0100;
+}
+
 static bool pci_moxa_match_x3xx(unsigned short device)
 {
 	return (device & 0x0F00) == 0x0300;
@@ -2016,6 +2025,36 @@ static int pci_moxa_set_interface(const struct pci_dev *dev,
 	return 0;
 }
 
+static int pci_moxa_rs485_config(struct uart_port *port,
+				 struct ktermios *termios,
+				 struct serial_rs485 *rs485)
+{
+	struct pci_dev *dev = to_pci_dev(port->dev);
+	unsigned short device = dev->device;
+	u8 mode = MOXA_RS232;
+
+	if (rs485->flags & SER_RS485_ENABLED) {
+		/* Use SER_RS485_TERMINATE_BUS to represent RS422 as a workaround. */
+		if (rs485->flags & SER_RS485_TERMINATE_BUS) {
+			mode = MOXA_RS422;
+		} else {
+			if (rs485->flags & SER_RS485_RX_DURING_TX)
+				mode = MOXA_RS485_4W;
+			else
+				mode = MOXA_RS485_2W;
+		}
+	} else {
+		/*
+		 * RS232 is not supported for those device IDs of
+		 * MOXA PCIe boards match the pattern 0x*3**.
+		 */
+		if (pci_moxa_match_x3xx(device))
+			return -EINVAL;
+	}
+
+	return pci_moxa_set_interface(dev, port->port_id, mode);
+}
+
 static int pci_moxa_init(struct pci_dev *dev)
 {
 	unsigned short device = dev->device;
@@ -2055,9 +2094,22 @@ pci_moxa_setup(struct serial_private *priv,
 		const struct pciserial_board *board,
 		struct uart_8250_port *port, int idx)
 {
+	struct pci_dev *dev = priv->dev;
+	unsigned short device = dev->device;
 	unsigned int bar = FL_GET_BASE(board->flags);
 	int offset;
 
+	/*
+	 * For the device IDs of MOXA PCIe boards match the pattern 0x*1** and 0x*3**,
+	 * these boards support switching interface between RS422/RS485 using TIOCSRS485.
+	 */
+	if (pci_moxa_match_x1xx(device) || pci_moxa_match_x3xx(device)) {
+		port->port.rs485_config = pci_moxa_rs485_config;
+		port->port.rs485_supported = pci_moxa_rs485_supported;
+
+		if (pci_moxa_match_x3xx(device))
+			port->port.rs485.flags |= SER_RS485_ENABLED | SER_RS485_TERMINATE_BUS;
+	}
 	if (board->num_ports == 4 && idx == 3)
 		offset = 7 * board->uart_offset;
 	else
-- 
2.34.1