[<prev] [next>] [thread-next>] [day] [month] [year] [list]
Message-Id: <20231017-th1520-mmc-v2-0-4678c8cc4048@baylibre.com>
Date: Tue, 17 Oct 2023 13:43:46 -0700
From: Drew Fustini <dfustini@...libre.com>
To: Ulf Hansson <ulf.hansson@...aro.org>,
Rob Herring <robh+dt@...nel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@...aro.org>,
Conor Dooley <conor+dt@...nel.org>,
Jisheng Zhang <jszhang@...nel.org>,
Adrian Hunter <adrian.hunter@...el.com>,
Guo Ren <guoren@...nel.org>, Fu Wei <wefu@...hat.com>,
Paul Walmsley <paul.walmsley@...ive.com>,
Palmer Dabbelt <palmer@...belt.com>,
Albert Ou <aou@...s.berkeley.edu>,
Conor Dooley <conor@...nel.org>
Cc: Robert Nelson <robertcnelson@...gleboard.org>,
Jason Kridner <jkridner@...gleboard.org>,
Xi Ruoyao <xry111@...111.site>, Han Gao <gaohan@...as.ac.cn>,
Icenowy Zheng <uwu@...nowy.me>, linux-mmc@...r.kernel.org,
devicetree@...r.kernel.org, linux-kernel@...r.kernel.org,
linux-riscv@...ts.infradead.org,
Drew Fustini <dfustini@...libre.com>
Subject: [PATCH v2 0/7] RISC-V: Add eMMC support for TH1520 boards
This series adds support for the eMMC on the BeagleV Ahead and the
Sipeed LicheePi 4A. This allows the kernel to boot with the rootfs on
eMMC.
I tested on top of v6.6-rc6 with riscv defconfig. I was able to boot
both the Ahead [1] and LPi4a [2] from eMMC. The following prerequisites
are required:
[PATCH v2] riscv: dts: thead: set dma-noncoherent to soc bus [3]
I pushed a branch [4] with this patch series and the above patch for
those that find a git branch easier to test.
Please note that only the MMC controller connected to the eMMC device
is enabled in the device trees for these two boards. I did not yet
attempt to configure and use the microSD card slot. My preference is to
address that in a future patch series.
References:
[1] https://gist.github.com/pdp7/7850027e8d256b6fd9cd53080240f0f6
[2] https://gist.github.com/pdp7/fae4637378426723508b679420a0a5a1
[3] https://lore.kernel.org/linux-riscv/20230912072232.2455-1-jszhang@kernel.org/
[4] https://github.com/pdp7/linux/tree/b4/th1520-mmc
Changes in PATCH v2:
- make use of BIT(), GENMASK(), FIELD_PREP(), FIELD_GET()
- add EXPORT_SYMBOL_GPL(__sdhci_execute_tuning)
- call th1520_phy_1_8v_init() when FLAG_IO_FIXED_1V8 is set
- set DWCMSHC_CARD_IS_EMMC when mmc caps contains MMC_CAP_NONREMOVABLE
- remove manipulation of AT_CTRL_AT_EN from th1520_set_uhs_signaling()
- remove unneccessary cycle of enabling and disabling AT_CTRL_AT_EN in
th1520_execute_tuning()
- remove th1520_phy_1_8v_init_no_pull()
- remove th1520_phy_3_3v_init_no_pull()
- remove FLAG_PULL_UP_EN from priv->flags
- remove thead,phy-pull-up device tree property
Changes in PACH v1:
https://lore.kernel.org/all/20230921-th1520-mmc-v1-0-49f76c274fb3@baylibre.com/
- ADMA mode now works correctly due to a patch from Jisheng on the list
("riscv: dts: thead: set dma-noncoherent to soc bus") and this commit
from Icenowy that is now merged: 8eb8fe67e2c8 ("riscv: errata: fix
T-Head dcache.cva encoding").
- Expose __sdhci_execute_tuning from sdhci.c so that it can be called
from th1520_execute_tuning()
- Refactor the define macros for all the PHY related registers to make
it easier to understand the bit fields that the code is manipulating
- Replace magic numbers in the PHY register writes with proper defines
- Replace non_removable in dwcmshc_priv with check of mmc_host.caps
- Drop dt prop "thead,io-fixed-1v8" and instead check for existing
properties: "mmc-ddr-1_8v", "mmc-hs200-1_8v", or "mmc-hs400-1_8v"
- Rename dt prop from "thead,pull-up" to "thead,phy-pull-up" and
improve the description in the dt binding
- Replace pull_up_en in dwcmshc_priv with bit field in new flags field
- Create th1520_set_uhs_signaling() and call dwcmshc_set_uhs_signaling()
from it instead of adding th1520 code to dwcmshc_set_uhs_signaling()
- Return -EIO instead of -1 upon errors in th1520_execute_tuning()
Changes in RFC v2:
https://lore.kernel.org/linux-riscv/20230724-th1520-emmc-v2-0-132ed2e2171e@baylibre.com/
- Expand dwcmshc_priv based on driver in the T-Head 5.10 kernel:
delay_line, non_removable, pull_up_en, io_fixed_1v8
- New boolean property "thead,pull-up" indicates phy pull-up config
- New boolean property "thead,io-fixed-1v8" indicates that io voltage
should be set to 1.8V during reset
- Add th1520_phy_1_8v_init() as voltage_switch op
- Add th1520_execute_tuning() as the platform_execute_tuning op
- Added th1520_sdhci_reset() as the .reset op. This function will set
io voltage to 1.8V after calling the standard sdhci_reset() function.
- Modified dwcmshc_set_uhs_signaling() to enable SDHCI_CTRL_VDD_180 when
io_fixed_1v8 is true
- Add many defines for register offsets and settings based on the mmc
support in the T-Head downstream v5.10 kernel
RFC v1 series:
https://lore.kernel.org/r/20230724-th1520-emmc-v1-0-cca1b2533da2@baylibre.com
Signed-off-by: Drew Fustini <dfustini@...libre.com>
---
Drew Fustini (7):
dt-bindings: mmc: sdhci-of-dwcmhsc: Add T-Head TH1520 support
mmc: sdhci: add __sdhci_execute_tuning() to header
mmc: sdhci-of-dwcmshc: Add support for T-Head TH1520
riscv: defconfig: Enable mmc and dma drivers for T-Head TH1520
riscv: dts: thead: Add TH1520 mmc controller and sdhci clock
riscv: dts: thead: Enable BeagleV Ahead eMMC controller
riscv: dts: thead: Enable LicheePi 4A eMMC controller
.../bindings/mmc/snps,dwcmshc-sdhci.yaml | 1 +
arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts | 14 +
.../boot/dts/thead/th1520-lichee-module-4a.dtsi | 14 +
arch/riscv/boot/dts/thead/th1520.dtsi | 15 +
arch/riscv/configs/defconfig | 2 +
drivers/mmc/host/sdhci-of-dwcmshc.c | 358 +++++++++++++++++++++
drivers/mmc/host/sdhci.c | 3 +-
drivers/mmc/host/sdhci.h | 1 +
8 files changed, 407 insertions(+), 1 deletion(-)
---
base-commit: f4c03b3d6c4bdafbb7885ccb84b095001eab1b88
change-id: 20231017-th1520-mmc-b7c72b7f56cd
Best regards,
--
Drew Fustini <dfustini@...libre.com>
Powered by blists - more mailing lists