| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20231107083525.24901-2-stanley_chang@realtek.com>
Date: Tue, 7 Nov 2023 16:31:41 +0800
From: Stanley Chang <stanley_chang@...ltek.com>
To: Greg Kroah-Hartman <gregkh@...uxfoundation.org>
CC: Stanley Chang <stanley_chang@...ltek.com>,
Vinod Koul <vkoul@...nel.org>, Johan Hovold <johan@...nel.org>,
Kishon Vijay Abraham I <kishon@...nel.org>,
Geert Uytterhoeven <geert+renesas@...der.be>,
Rob Herring <robh@...nel.org>,
Jinjie Ruan <ruanjinjie@...wei.com>,
Alan Stern <stern@...land.harvard.edu>,
Yang Yingliang <yangyingliang@...wei.com>,
Roy Luo <royluo@...gle.com>,
Ricardo Cañuelo <ricardo.canuelo@...labora.com>,
"Heikki Krogerus" <heikki.krogerus@...ux.intel.com>,
Ray Chi <raychi@...gle.com>, <linux-kernel@...r.kernel.org>,
<linux-phy@...ts.infradead.org>, <linux-usb@...r.kernel.org>
Subject: [PATCH v2 2/4] phy: realtek: usb: add new driver for the Realtek RTD SoC USB 2.0 PHY
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller. Added the driver to drive the USB 2.0 PHY transceivers.
Note: New driver,remove the port status notification on legacy USB PHY.
Use the generic PHY to notify the usb device connect and disconnect.
To avoid using these PHYs would require describing the very same
PHY using both the generic "phy" property and the deprecated "usb-phy"
property.
Signed-off-by: Stanley Chang <stanley_chang@...ltek.com>
---
v1 to v2 change:
rebase the driver to include the revert part on
7a784bcdd7e54f0599da3b2360e472238412623e
---
drivers/phy/Kconfig | 1 +
drivers/phy/Makefile | 1 +
drivers/phy/realtek/Kconfig | 20 +
drivers/phy/realtek/Makefile | 2 +
drivers/phy/realtek/phy-rtk-usb2.c | 1313 ++++++++++++++++++++++++++++
5 files changed, 1337 insertions(+)
create mode 100644 drivers/phy/realtek/Kconfig
create mode 100644 drivers/phy/realtek/Makefile
create mode 100644 drivers/phy/realtek/phy-rtk-usb2.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 4cef568231bf..787354b849c7 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -87,6 +87,7 @@ source "drivers/phy/motorola/Kconfig"
source "drivers/phy/mscc/Kconfig"
source "drivers/phy/qualcomm/Kconfig"
source "drivers/phy/ralink/Kconfig"
+source "drivers/phy/realtek/Kconfig"
source "drivers/phy/renesas/Kconfig"
source "drivers/phy/rockchip/Kconfig"
source "drivers/phy/samsung/Kconfig"
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index fb3dc9de6111..868a220ed0f6 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -26,6 +26,7 @@ obj-y += allwinner/ \
mscc/ \
qualcomm/ \
ralink/ \
+ realtek/ \
renesas/ \
rockchip/ \
samsung/ \
diff --git a/drivers/phy/realtek/Kconfig b/drivers/phy/realtek/Kconfig
new file mode 100644
index 000000000000..745587751070
--- /dev/null
+++ b/drivers/phy/realtek/Kconfig
@@ -0,0 +1,20 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Phy drivers for Realtek platforms
+#
+
+if ARCH_REALTEK || COMPILE_TEST
+
+config PHY_RTK_RTD_USB2PHY
+ tristate "Realtek RTD USB2 PHY Transceiver Driver"
+ depends on USB_SUPPORT
+ select GENERIC_PHY
+ select USB_PHY
+ select USB_COMMON
+ help
+ Enable this to support Realtek SoC USB2 phy transceiver.
+ The DHC (digital home center) RTD series SoCs used the Synopsys
+ DWC3 USB IP. This driver will do the PHY initialization
+ of the parameters.
+
+endif # ARCH_REALTEK || COMPILE_TEST
diff --git a/drivers/phy/realtek/Makefile b/drivers/phy/realtek/Makefile
new file mode 100644
index 000000000000..cf5d440841a2
--- /dev/null
+++ b/drivers/phy/realtek/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_PHY_RTK_RTD_USB2PHY) += phy-rtk-usb2.o
diff --git a/drivers/phy/realtek/phy-rtk-usb2.c b/drivers/phy/realtek/phy-rtk-usb2.c
new file mode 100644
index 000000000000..9cd2329fd7ca
--- /dev/null
+++ b/drivers/phy/realtek/phy-rtk-usb2.c
@@ -0,0 +1,1313 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * phy-rtk-usb2.c RTK usb2.0 PHY driver
+ *
+ * Copyright (C) 2023 Realtek Semiconductor Corporation
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/uaccess.h>
+#include <linux/debugfs.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/regmap.h>
+#include <linux/sys_soc.h>
+#include <linux/mfd/syscon.h>
+#include <linux/phy/phy.h>
+#include <linux/usb.h>
+
+/* GUSB2PHYACCn register */
+#define PHY_NEW_REG_REQ BIT(25)
+#define PHY_VSTS_BUSY BIT(23)
+#define PHY_VCTRL_SHIFT 8
+#define PHY_REG_DATA_MASK 0xff
+
+#define GET_LOW_NIBBLE(addr) ((addr) & 0x0f)
+#define GET_HIGH_NIBBLE(addr) (((addr) & 0xf0) >> 4)
+
+#define EFUS_USB_DC_CAL_RATE 2
+#define EFUS_USB_DC_CAL_MAX 7
+
+#define EFUS_USB_DC_DIS_RATE 1
+#define EFUS_USB_DC_DIS_MAX 7
+
+#define MAX_PHY_DATA_SIZE 20
+#define OFFEST_PHY_READ 0x20
+
+#define MAX_USB_PHY_NUM 4
+#define MAX_USB_PHY_PAGE0_DATA_SIZE 16
+#define MAX_USB_PHY_PAGE1_DATA_SIZE 16
+#define MAX_USB_PHY_PAGE2_DATA_SIZE 8
+
+#define SET_PAGE_OFFSET 0xf4
+#define SET_PAGE_0 0x9b
+#define SET_PAGE_1 0xbb
+#define SET_PAGE_2 0xdb
+
+#define PAGE_START 0xe0
+#define PAGE0_0XE4 0xe4
+#define PAGE0_0XE6 0xe6
+#define PAGE0_0XE7 0xe7
+#define PAGE1_0XE0 0xe0
+#define PAGE1_0XE2 0xe2
+
+#define SENSITIVITY_CTRL (BIT(4) | BIT(5) | BIT(6))
+#define ENABLE_AUTO_SENSITIVITY_CALIBRATION BIT(2)
+#define DEFAULT_DC_DRIVING_VALUE (0x8)
+#define DEFAULT_DC_DISCONNECTION_VALUE (0x6)
+#define HS_CLK_SELECT BIT(6)
+
+struct phy_reg {
+ void __iomem *reg_wrap_vstatus;
+ void __iomem *reg_gusb2phyacc0;
+ int vstatus_index;
+};
+
+struct phy_data {
+ u8 addr;
+ u8 data;
+};
+
+struct phy_cfg {
+ int page0_size;
+ struct phy_data page0[MAX_USB_PHY_PAGE0_DATA_SIZE];
+ int page1_size;
+ struct phy_data page1[MAX_USB_PHY_PAGE1_DATA_SIZE];
+ int page2_size;
+ struct phy_data page2[MAX_USB_PHY_PAGE2_DATA_SIZE];
+
+ int num_phy;
+
+ bool check_efuse;
+ int check_efuse_version;
+#define CHECK_EFUSE_V1 1
+#define CHECK_EFUSE_V2 2
+ int efuse_dc_driving_rate;
+ int efuse_dc_disconnect_rate;
+ int dc_driving_mask;
+ int dc_disconnect_mask;
+ bool usb_dc_disconnect_at_page0;
+ int driving_updated_for_dev_dis;
+
+ bool do_toggle;
+ bool do_toggle_driving;
+ bool use_default_parameter;
+ bool is_double_sensitivity_mode;
+};
+
+struct phy_parameter {
+ struct phy_reg phy_reg;
+
+ /* Get from efuse */
+ s8 efuse_usb_dc_cal;
+ s8 efuse_usb_dc_dis;
+
+ /* Get from dts */
+ bool inverse_hstx_sync_clock;
+ u32 driving_level;
+ s32 driving_level_compensate;
+ s32 disconnection_compensate;
+};
+
+struct rtk_phy {
+ struct device *dev;
+
+ struct phy_cfg *phy_cfg;
+ int num_phy;
+ struct phy_parameter *phy_parameter;
+
+ struct dentry *debug_dir;
+};
+
+/* mapping 0xE0 to 0 ... 0xE7 to 7, 0xF0 to 8 ,,, 0xF7 to 15 */
+static inline int page_addr_to_array_index(u8 addr)
+{
+ return (int)((((addr) - PAGE_START) & 0x7) +
+ ((((addr) - PAGE_START) & 0x10) >> 1));
+}
+
+static inline u8 array_index_to_page_addr(int index)
+{
+ return ((((index) + PAGE_START) & 0x7) +
+ ((((index) & 0x8) << 1) + PAGE_START));
+}
+
+#define PHY_IO_TIMEOUT_USEC (50000)
+#define PHY_IO_DELAY_US (100)
+
+static inline int utmi_wait_register(void __iomem *reg, u32 mask, u32 result)
+{
+ int ret;
+ unsigned int val;
+
+ ret = read_poll_timeout(readl, val, ((val & mask) == result),
+ PHY_IO_DELAY_US, PHY_IO_TIMEOUT_USEC, false, reg);
+ if (ret) {
+ pr_err("%s can't program USB phy\n", __func__);
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static char rtk_phy_read(struct phy_reg *phy_reg, char addr)
+{
+ void __iomem *reg_gusb2phyacc0 = phy_reg->reg_gusb2phyacc0;
+ unsigned int val;
+ int ret = 0;
+
+ addr -= OFFEST_PHY_READ;
+
+ /* polling until VBusy == 0 */
+ ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ if (ret)
+ return (char)ret;
+
+ /* VCtrl = low nibble of addr, and set PHY_NEW_REG_REQ */
+ val = PHY_NEW_REG_REQ | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+ writel(val, reg_gusb2phyacc0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ if (ret)
+ return (char)ret;
+
+ /* VCtrl = high nibble of addr, and set PHY_NEW_REG_REQ */
+ val = PHY_NEW_REG_REQ | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+ writel(val, reg_gusb2phyacc0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ if (ret)
+ return (char)ret;
+
+ val = readl(reg_gusb2phyacc0);
+
+ return (char)(val & PHY_REG_DATA_MASK);
+}
+
+static int rtk_phy_write(struct phy_reg *phy_reg, char addr, char data)
+{
+ unsigned int val;
+ void __iomem *reg_wrap_vstatus = phy_reg->reg_wrap_vstatus;
+ void __iomem *reg_gusb2phyacc0 = phy_reg->reg_gusb2phyacc0;
+ int shift_bits = phy_reg->vstatus_index * 8;
+ int ret = 0;
+
+ /* write data to VStatusOut2 (data output to phy) */
+ writel((u32)data << shift_bits, reg_wrap_vstatus);
+
+ ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ if (ret)
+ return ret;
+
+ /* VCtrl = low nibble of addr, set PHY_NEW_REG_REQ */
+ val = PHY_NEW_REG_REQ | (GET_LOW_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+
+ writel(val, reg_gusb2phyacc0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ if (ret)
+ return ret;
+
+ /* VCtrl = high nibble of addr, set PHY_NEW_REG_REQ */
+ val = PHY_NEW_REG_REQ | (GET_HIGH_NIBBLE(addr) << PHY_VCTRL_SHIFT);
+
+ writel(val, reg_gusb2phyacc0);
+ ret = utmi_wait_register(reg_gusb2phyacc0, PHY_VSTS_BUSY, 0);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int rtk_phy_set_page(struct phy_reg *phy_reg, int page)
+{
+ switch (page) {
+ case 0:
+ return rtk_phy_write(phy_reg, SET_PAGE_OFFSET, SET_PAGE_0);
+ case 1:
+ return rtk_phy_write(phy_reg, SET_PAGE_OFFSET, SET_PAGE_1);
+ case 2:
+ return rtk_phy_write(phy_reg, SET_PAGE_OFFSET, SET_PAGE_2);
+ default:
+ pr_err("%s error page=%d\n", __func__, page);
+ }
+
+ return -EINVAL;
+}
+
+static u8 __updated_dc_disconnect_level_page0_0xe4(struct phy_cfg *phy_cfg,
+ struct phy_parameter *phy_parameter, u8 data)
+{
+ u8 ret;
+ s32 val;
+ s32 dc_disconnect_mask = phy_cfg->dc_disconnect_mask;
+ int offset = 4;
+
+ val = (s32)((data >> offset) & dc_disconnect_mask)
+ + phy_parameter->efuse_usb_dc_dis
+ + phy_parameter->disconnection_compensate;
+
+ if (val > dc_disconnect_mask)
+ val = dc_disconnect_mask;
+ else if (val < 0)
+ val = 0;
+
+ ret = (data & (~(dc_disconnect_mask << offset))) |
+ (val & dc_disconnect_mask) << offset;
+
+ return ret;
+}
+
+/* updated disconnect level at page0 */
+static void update_dc_disconnect_level_at_page0(struct rtk_phy *rtk_phy,
+ struct phy_parameter *phy_parameter, bool update)
+{
+ struct phy_cfg *phy_cfg;
+ struct phy_reg *phy_reg;
+ struct phy_data *phy_data_page;
+ struct phy_data *phy_data;
+ u8 addr, data;
+ int offset = 4;
+ s32 dc_disconnect_mask;
+ int i;
+
+ phy_cfg = rtk_phy->phy_cfg;
+ phy_reg = &phy_parameter->phy_reg;
+
+ /* Set page 0 */
+ phy_data_page = phy_cfg->page0;
+ rtk_phy_set_page(phy_reg, 0);
+
+ i = page_addr_to_array_index(PAGE0_0XE4);
+ phy_data = phy_data_page + i;
+ if (!phy_data->addr) {
+ phy_data->addr = PAGE0_0XE4;
+ phy_data->data = rtk_phy_read(phy_reg, PAGE0_0XE4);
+ }
+
+ addr = phy_data->addr;
+ data = phy_data->data;
+ dc_disconnect_mask = phy_cfg->dc_disconnect_mask;
+
+ if (update)
+ data = __updated_dc_disconnect_level_page0_0xe4(phy_cfg, phy_parameter, data);
+ else
+ data = (data & ~(dc_disconnect_mask << offset)) |
+ (DEFAULT_DC_DISCONNECTION_VALUE << offset);
+
+ if (rtk_phy_write(phy_reg, addr, data))
+ dev_err(rtk_phy->dev,
+ "%s: Error to set page1 parameter addr=0x%x value=0x%x\n",
+ __func__, addr, data);
+}
+
+static u8 __updated_dc_disconnect_level_page1_0xe2(struct phy_cfg *phy_cfg,
+ struct phy_parameter *phy_parameter, u8 data)
+{
+ u8 ret;
+ s32 val;
+ s32 dc_disconnect_mask = phy_cfg->dc_disconnect_mask;
+
+ if (phy_cfg->check_efuse_version == CHECK_EFUSE_V1) {
+ val = (s32)(data & dc_disconnect_mask)
+ + phy_parameter->efuse_usb_dc_dis
+ + phy_parameter->disconnection_compensate;
+ } else { /* for CHECK_EFUSE_V2 or no efuse */
+ if (phy_parameter->efuse_usb_dc_dis)
+ val = (s32)(phy_parameter->efuse_usb_dc_dis +
+ phy_parameter->disconnection_compensate);
+ else
+ val = (s32)((data & dc_disconnect_mask) +
+ phy_parameter->disconnection_compensate);
+ }
+
+ if (val > dc_disconnect_mask)
+ val = dc_disconnect_mask;
+ else if (val < 0)
+ val = 0;
+
+ ret = (data & (~dc_disconnect_mask)) | (val & dc_disconnect_mask);
+
+ return ret;
+}
+
+/* updated disconnect level at page1 */
+static void update_dc_disconnect_level_at_page1(struct rtk_phy *rtk_phy,
+ struct phy_parameter *phy_parameter, bool update)
+{
+ struct phy_cfg *phy_cfg;
+ struct phy_data *phy_data_page;
+ struct phy_data *phy_data;
+ struct phy_reg *phy_reg;
+ u8 addr, data;
+ s32 dc_disconnect_mask;
+ int i;
+
+ phy_cfg = rtk_phy->phy_cfg;
+ phy_reg = &phy_parameter->phy_reg;
+
+ /* Set page 1 */
+ phy_data_page = phy_cfg->page1;
+ rtk_phy_set_page(phy_reg, 1);
+
+ i = page_addr_to_array_index(PAGE1_0XE2);
+ phy_data = phy_data_page + i;
+ if (!phy_data->addr) {
+ phy_data->addr = PAGE1_0XE2;
+ phy_data->data = rtk_phy_read(phy_reg, PAGE1_0XE2);
+ }
+
+ addr = phy_data->addr;
+ data = phy_data->data;
+ dc_disconnect_mask = phy_cfg->dc_disconnect_mask;
+
+ if (update)
+ data = __updated_dc_disconnect_level_page1_0xe2(phy_cfg, phy_parameter, data);
+ else
+ data = (data & ~dc_disconnect_mask) | DEFAULT_DC_DISCONNECTION_VALUE;
+
+ if (rtk_phy_write(phy_reg, addr, data))
+ dev_err(rtk_phy->dev,
+ "%s: Error to set page1 parameter addr=0x%x value=0x%x\n",
+ __func__, addr, data);
+}
+
+static void update_dc_disconnect_level(struct rtk_phy *rtk_phy,
+ struct phy_parameter *phy_parameter, bool update)
+{
+ struct phy_cfg *phy_cfg = rtk_phy->phy_cfg;
+
+ if (phy_cfg->usb_dc_disconnect_at_page0)
+ update_dc_disconnect_level_at_page0(rtk_phy, phy_parameter, update);
+ else
+ update_dc_disconnect_level_at_page1(rtk_phy, phy_parameter, update);
+}
+
+static u8 __update_dc_driving_page0_0xe4(struct phy_cfg *phy_cfg,
+ struct phy_parameter *phy_parameter, u8 data)
+{
+ s32 driving_level_compensate = phy_parameter->driving_level_compensate;
+ s32 dc_driving_mask = phy_cfg->dc_driving_mask;
+ s32 val;
+ u8 ret;
+
+ if (phy_cfg->check_efuse_version == CHECK_EFUSE_V1) {
+ val = (s32)(data & dc_driving_mask) + driving_level_compensate
+ + phy_parameter->efuse_usb_dc_cal;
+ } else { /* for CHECK_EFUSE_V2 or no efuse */
+ if (phy_parameter->efuse_usb_dc_cal)
+ val = (s32)((phy_parameter->efuse_usb_dc_cal & dc_driving_mask)
+ + driving_level_compensate);
+ else
+ val = (s32)(data & dc_driving_mask);
+ }
+
+ if (val > dc_driving_mask)
+ val = dc_driving_mask;
+ else if (val < 0)
+ val = 0;
+
+ ret = (data & (~dc_driving_mask)) | (val & dc_driving_mask);
+
+ return ret;
+}
+
+static void update_dc_driving_level(struct rtk_phy *rtk_phy,
+ struct phy_parameter *phy_parameter)
+{
+ struct phy_cfg *phy_cfg;
+ struct phy_reg *phy_reg;
+
+ phy_reg = &phy_parameter->phy_reg;
+ phy_cfg = rtk_phy->phy_cfg;
+ if (!phy_cfg->page0[4].addr) {
+ rtk_phy_set_page(phy_reg, 0);
+ phy_cfg->page0[4].addr = PAGE0_0XE4;
+ phy_cfg->page0[4].data = rtk_phy_read(phy_reg, PAGE0_0XE4);
+ }
+
+ if (phy_parameter->driving_level != DEFAULT_DC_DRIVING_VALUE) {
+ u32 dc_driving_mask;
+ u8 driving_level;
+ u8 data;
+
+ data = phy_cfg->page0[4].data;
+ dc_driving_mask = phy_cfg->dc_driving_mask;
+ driving_level = data & dc_driving_mask;
+
+ dev_dbg(rtk_phy->dev, "%s driving_level=%d => dts driving_level=%d\n",
+ __func__, driving_level, phy_parameter->driving_level);
+
+ phy_cfg->page0[4].data = (data & (~dc_driving_mask)) |
+ (phy_parameter->driving_level & dc_driving_mask);
+ }
+
+ phy_cfg->page0[4].data = __update_dc_driving_page0_0xe4(phy_cfg,
+ phy_parameter,
+ phy_cfg->page0[4].data);
+}
+
+static void update_hs_clk_select(struct rtk_phy *rtk_phy,
+ struct phy_parameter *phy_parameter)
+{
+ struct phy_cfg *phy_cfg;
+ struct phy_reg *phy_reg;
+
+ phy_cfg = rtk_phy->phy_cfg;
+ phy_reg = &phy_parameter->phy_reg;
+
+ if (phy_parameter->inverse_hstx_sync_clock) {
+ if (!phy_cfg->page0[6].addr) {
+ rtk_phy_set_page(phy_reg, 0);
+ phy_cfg->page0[6].addr = PAGE0_0XE6;
+ phy_cfg->page0[6].data = rtk_phy_read(phy_reg, PAGE0_0XE6);
+ }
+
+ phy_cfg->page0[6].data = phy_cfg->page0[6].data | HS_CLK_SELECT;
+ }
+}
+
+static void do_rtk_phy_toggle(struct rtk_phy *rtk_phy,
+ int index, bool connect)
+{
+ struct phy_parameter *phy_parameter;
+ struct phy_cfg *phy_cfg;
+ struct phy_reg *phy_reg;
+ struct phy_data *phy_data_page;
+ u8 addr, data;
+ int i;
+
+ phy_cfg = rtk_phy->phy_cfg;
+ phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
+ phy_reg = &phy_parameter->phy_reg;
+
+ if (!phy_cfg->do_toggle)
+ goto out;
+
+ if (phy_cfg->is_double_sensitivity_mode)
+ goto do_toggle_driving;
+
+ /* Set page 0 */
+ rtk_phy_set_page(phy_reg, 0);
+
+ addr = PAGE0_0XE7;
+ data = rtk_phy_read(phy_reg, addr);
+
+ if (connect)
+ rtk_phy_write(phy_reg, addr, data & (~SENSITIVITY_CTRL));
+ else
+ rtk_phy_write(phy_reg, addr, data | (SENSITIVITY_CTRL));
+
+do_toggle_driving:
+
+ if (!phy_cfg->do_toggle_driving)
+ goto do_toggle;
+
+ /* Page 0 addr 0xE4 driving capability */
+
+ /* Set page 0 */
+ phy_data_page = phy_cfg->page0;
+ rtk_phy_set_page(phy_reg, 0);
+
+ i = page_addr_to_array_index(PAGE0_0XE4);
+ addr = phy_data_page[i].addr;
+ data = phy_data_page[i].data;
+
+ if (connect) {
+ rtk_phy_write(phy_reg, addr, data);
+ } else {
+ u8 value;
+ s32 tmp;
+ s32 driving_updated =
+ phy_cfg->driving_updated_for_dev_dis;
+ s32 dc_driving_mask = phy_cfg->dc_driving_mask;
+
+ tmp = (s32)(data & dc_driving_mask) + driving_updated;
+
+ if (tmp > dc_driving_mask)
+ tmp = dc_driving_mask;
+ else if (tmp < 0)
+ tmp = 0;
+
+ value = (data & (~dc_driving_mask)) | (tmp & dc_driving_mask);
+
+ rtk_phy_write(phy_reg, addr, value);
+ }
+
+do_toggle:
+ /* restore dc disconnect level before toggle */
+ update_dc_disconnect_level(rtk_phy, phy_parameter, false);
+
+ /* Set page 1 */
+ rtk_phy_set_page(phy_reg, 1);
+
+ addr = PAGE1_0XE0;
+ data = rtk_phy_read(phy_reg, addr);
+
+ rtk_phy_write(phy_reg, addr, data &
+ (~ENABLE_AUTO_SENSITIVITY_CALIBRATION));
+ mdelay(1);
+ rtk_phy_write(phy_reg, addr, data |
+ (ENABLE_AUTO_SENSITIVITY_CALIBRATION));
+
+ /* update dc disconnect level after toggle */
+ update_dc_disconnect_level(rtk_phy, phy_parameter, true);
+
+out:
+ return;
+}
+
+static int do_rtk_phy_init(struct rtk_phy *rtk_phy, int index)
+{
+ struct phy_parameter *phy_parameter;
+ struct phy_cfg *phy_cfg;
+ struct phy_data *phy_data_page;
+ struct phy_reg *phy_reg;
+ int i;
+
+ phy_cfg = rtk_phy->phy_cfg;
+ phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
+ phy_reg = &phy_parameter->phy_reg;
+
+ if (phy_cfg->use_default_parameter) {
+ dev_dbg(rtk_phy->dev, "%s phy#%d use default parameter\n",
+ __func__, index);
+ goto do_toggle;
+ }
+
+ /* Set page 0 */
+ phy_data_page = phy_cfg->page0;
+ rtk_phy_set_page(phy_reg, 0);
+
+ for (i = 0; i < phy_cfg->page0_size; i++) {
+ struct phy_data *phy_data = phy_data_page + i;
+ u8 addr = phy_data->addr;
+ u8 data = phy_data->data;
+
+ if (!addr)
+ continue;
+
+ if (rtk_phy_write(phy_reg, addr, data)) {
+ dev_err(rtk_phy->dev,
+ "%s: Error to set page0 parameter addr=0x%x value=0x%x\n",
+ __func__, addr, data);
+ return -EINVAL;
+ }
+ }
+
+ /* Set page 1 */
+ phy_data_page = phy_cfg->page1;
+ rtk_phy_set_page(phy_reg, 1);
+
+ for (i = 0; i < phy_cfg->page1_size; i++) {
+ struct phy_data *phy_data = phy_data_page + i;
+ u8 addr = phy_data->addr;
+ u8 data = phy_data->data;
+
+ if (!addr)
+ continue;
+
+ if (rtk_phy_write(phy_reg, addr, data)) {
+ dev_err(rtk_phy->dev,
+ "%s: Error to set page1 parameter addr=0x%x value=0x%x\n",
+ __func__, addr, data);
+ return -EINVAL;
+ }
+ }
+
+ if (phy_cfg->page2_size == 0)
+ goto do_toggle;
+
+ /* Set page 2 */
+ phy_data_page = phy_cfg->page2;
+ rtk_phy_set_page(phy_reg, 2);
+
+ for (i = 0; i < phy_cfg->page2_size; i++) {
+ struct phy_data *phy_data = phy_data_page + i;
+ u8 addr = phy_data->addr;
+ u8 data = phy_data->data;
+
+ if (!addr)
+ continue;
+
+ if (rtk_phy_write(phy_reg, addr, data)) {
+ dev_err(rtk_phy->dev,
+ "%s: Error to set page2 parameter addr=0x%x value=0x%x\n",
+ __func__, addr, data);
+ return -EINVAL;
+ }
+ }
+
+do_toggle:
+ do_rtk_phy_toggle(rtk_phy, index, false);
+
+ return 0;
+}
+
+static int rtk_phy_init(struct phy *phy)
+{
+ struct rtk_phy *rtk_phy = phy_get_drvdata(phy);
+ unsigned long phy_init_time = jiffies;
+ int i, ret = 0;
+
+ if (!rtk_phy)
+ return -EINVAL;
+
+ for (i = 0; i < rtk_phy->num_phy; i++)
+ ret = do_rtk_phy_init(rtk_phy, i);
+
+ dev_dbg(rtk_phy->dev, "Initialized RTK USB 2.0 PHY (take %dms)\n",
+ jiffies_to_msecs(jiffies - phy_init_time));
+ return ret;
+}
+
+static int rtk_phy_exit(struct phy *phy)
+{
+ return 0;
+}
+
+static void rtk_phy_toggle(struct rtk_phy *rtk_phy, bool connect, int port)
+{
+ int index = port;
+
+ if (index > rtk_phy->num_phy) {
+ dev_err(rtk_phy->dev, "%s: The port=%d is not in usb phy (num_phy=%d)\n",
+ __func__, index, rtk_phy->num_phy);
+ return;
+ }
+
+ do_rtk_phy_toggle(rtk_phy, index, connect);
+}
+
+static int rtk_phy_connect(struct phy *phy, int port)
+{
+ struct rtk_phy *rtk_phy = phy_get_drvdata(phy);
+
+ dev_dbg(rtk_phy->dev, "%s port=%d\n", __func__, port);
+ rtk_phy_toggle(rtk_phy, true, port);
+
+ return 0;
+}
+
+static int rtk_phy_disconnect(struct phy *phy, int port)
+{
+ struct rtk_phy *rtk_phy = phy_get_drvdata(phy);
+
+ dev_dbg(rtk_phy->dev, "%s port=%d\n", __func__, port);
+ rtk_phy_toggle(rtk_phy, false, port);
+
+ return 0;
+}
+
+static const struct phy_ops ops = {
+ .init = rtk_phy_init,
+ .exit = rtk_phy_exit,
+ .connect = rtk_phy_connect,
+ .disconnect = rtk_phy_disconnect,
+ .owner = THIS_MODULE,
+};
+
+#ifdef CONFIG_DEBUG_FS
+static struct dentry *create_phy_debug_root(void)
+{
+ struct dentry *phy_debug_root;
+
+ phy_debug_root = debugfs_lookup("phy", usb_debug_root);
+ if (!phy_debug_root)
+ phy_debug_root = debugfs_create_dir("phy", usb_debug_root);
+
+ return phy_debug_root;
+}
+
+static int rtk_usb2_parameter_show(struct seq_file *s, void *unused)
+{
+ struct rtk_phy *rtk_phy = s->private;
+ struct phy_cfg *phy_cfg;
+ int i, index;
+
+ phy_cfg = rtk_phy->phy_cfg;
+
+ seq_puts(s, "Property:\n");
+ seq_printf(s, " check_efuse: %s\n",
+ phy_cfg->check_efuse ? "Enable" : "Disable");
+ seq_printf(s, " check_efuse_version: %d\n",
+ phy_cfg->check_efuse_version);
+ seq_printf(s, " efuse_dc_driving_rate: %d\n",
+ phy_cfg->efuse_dc_driving_rate);
+ seq_printf(s, " dc_driving_mask: 0x%x\n",
+ phy_cfg->dc_driving_mask);
+ seq_printf(s, " efuse_dc_disconnect_rate: %d\n",
+ phy_cfg->efuse_dc_disconnect_rate);
+ seq_printf(s, " dc_disconnect_mask: 0x%x\n",
+ phy_cfg->dc_disconnect_mask);
+ seq_printf(s, " usb_dc_disconnect_at_page0: %s\n",
+ phy_cfg->usb_dc_disconnect_at_page0 ? "true" : "false");
+ seq_printf(s, " do_toggle: %s\n",
+ phy_cfg->do_toggle ? "Enable" : "Disable");
+ seq_printf(s, " do_toggle_driving: %s\n",
+ phy_cfg->do_toggle_driving ? "Enable" : "Disable");
+ seq_printf(s, " driving_updated_for_dev_dis: 0x%x\n",
+ phy_cfg->driving_updated_for_dev_dis);
+ seq_printf(s, " use_default_parameter: %s\n",
+ phy_cfg->use_default_parameter ? "Enable" : "Disable");
+ seq_printf(s, " is_double_sensitivity_mode: %s\n",
+ phy_cfg->is_double_sensitivity_mode ? "Enable" : "Disable");
+
+ for (index = 0; index < rtk_phy->num_phy; index++) {
+ struct phy_parameter *phy_parameter;
+ struct phy_reg *phy_reg;
+ struct phy_data *phy_data_page;
+
+ phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
+ phy_reg = &phy_parameter->phy_reg;
+
+ seq_printf(s, "PHY %d:\n", index);
+
+ seq_puts(s, "Page 0:\n");
+ /* Set page 0 */
+ phy_data_page = phy_cfg->page0;
+ rtk_phy_set_page(phy_reg, 0);
+
+ for (i = 0; i < phy_cfg->page0_size; i++) {
+ struct phy_data *phy_data = phy_data_page + i;
+ u8 addr = array_index_to_page_addr(i);
+ u8 data = phy_data->data;
+ u8 value = rtk_phy_read(phy_reg, addr);
+
+ if (phy_data->addr)
+ seq_printf(s, " Page 0: addr=0x%x data=0x%02x ==> read value=0x%02x\n",
+ addr, data, value);
+ else
+ seq_printf(s, " Page 0: addr=0x%x data=none ==> read value=0x%02x\n",
+ addr, value);
+ }
+
+ seq_puts(s, "Page 1:\n");
+ /* Set page 1 */
+ phy_data_page = phy_cfg->page1;
+ rtk_phy_set_page(phy_reg, 1);
+
+ for (i = 0; i < phy_cfg->page1_size; i++) {
+ struct phy_data *phy_data = phy_data_page + i;
+ u8 addr = array_index_to_page_addr(i);
+ u8 data = phy_data->data;
+ u8 value = rtk_phy_read(phy_reg, addr);
+
+ if (phy_data->addr)
+ seq_printf(s, " Page 1: addr=0x%x data=0x%02x ==> read value=0x%02x\n",
+ addr, data, value);
+ else
+ seq_printf(s, " Page 1: addr=0x%x data=none ==> read value=0x%02x\n",
+ addr, value);
+ }
+
+ if (phy_cfg->page2_size == 0)
+ goto out;
+
+ seq_puts(s, "Page 2:\n");
+ /* Set page 2 */
+ phy_data_page = phy_cfg->page2;
+ rtk_phy_set_page(phy_reg, 2);
+
+ for (i = 0; i < phy_cfg->page2_size; i++) {
+ struct phy_data *phy_data = phy_data_page + i;
+ u8 addr = array_index_to_page_addr(i);
+ u8 data = phy_data->data;
+ u8 value = rtk_phy_read(phy_reg, addr);
+
+ if (phy_data->addr)
+ seq_printf(s, " Page 2: addr=0x%x data=0x%02x ==> read value=0x%02x\n",
+ addr, data, value);
+ else
+ seq_printf(s, " Page 2: addr=0x%x data=none ==> read value=0x%02x\n",
+ addr, value);
+ }
+
+out:
+ seq_puts(s, "PHY Property:\n");
+ seq_printf(s, " efuse_usb_dc_cal: %d\n",
+ (int)phy_parameter->efuse_usb_dc_cal);
+ seq_printf(s, " efuse_usb_dc_dis: %d\n",
+ (int)phy_parameter->efuse_usb_dc_dis);
+ seq_printf(s, " inverse_hstx_sync_clock: %s\n",
+ phy_parameter->inverse_hstx_sync_clock ? "Enable" : "Disable");
+ seq_printf(s, " driving_level: %d\n",
+ phy_parameter->driving_level);
+ seq_printf(s, " driving_level_compensate: %d\n",
+ phy_parameter->driving_level_compensate);
+ seq_printf(s, " disconnection_compensate: %d\n",
+ phy_parameter->disconnection_compensate);
+ }
+
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(rtk_usb2_parameter);
+
+static inline void create_debug_files(struct rtk_phy *rtk_phy)
+{
+ struct dentry *phy_debug_root = NULL;
+
+ phy_debug_root = create_phy_debug_root();
+ if (!phy_debug_root)
+ return;
+
+ rtk_phy->debug_dir = debugfs_create_dir(dev_name(rtk_phy->dev),
+ phy_debug_root);
+
+ debugfs_create_file("parameter", 0444, rtk_phy->debug_dir, rtk_phy,
+ &rtk_usb2_parameter_fops);
+}
+
+static inline void remove_debug_files(struct rtk_phy *rtk_phy)
+{
+ debugfs_remove_recursive(rtk_phy->debug_dir);
+}
+#else
+static inline void create_debug_files(struct rtk_phy *rtk_phy) { }
+static inline void remove_debug_files(struct rtk_phy *rtk_phy) { }
+#endif /* CONFIG_DEBUG_FS */
+
+static int get_phy_data_by_efuse(struct rtk_phy *rtk_phy,
+ struct phy_parameter *phy_parameter, int index)
+{
+ struct phy_cfg *phy_cfg = rtk_phy->phy_cfg;
+ u8 value = 0;
+ struct nvmem_cell *cell;
+ struct soc_device_attribute rtk_soc_groot[] = {
+ { .family = "Realtek Groot",},
+ { /* empty */ } };
+
+ if (!phy_cfg->check_efuse)
+ goto out;
+
+ /* Read efuse for usb dc cal */
+ cell = nvmem_cell_get(rtk_phy->dev, "usb-dc-cal");
+ if (IS_ERR(cell)) {
+ dev_dbg(rtk_phy->dev, "%s no usb-dc-cal: %ld\n",
+ __func__, PTR_ERR(cell));
+ } else {
+ unsigned char *buf;
+ size_t buf_size;
+
+ buf = nvmem_cell_read(cell, &buf_size);
+ if (!IS_ERR(buf)) {
+ value = buf[0] & phy_cfg->dc_driving_mask;
+ kfree(buf);
+ }
+ nvmem_cell_put(cell);
+ }
+
+ if (phy_cfg->check_efuse_version == CHECK_EFUSE_V1) {
+ int rate = phy_cfg->efuse_dc_driving_rate;
+
+ if (value <= EFUS_USB_DC_CAL_MAX)
+ phy_parameter->efuse_usb_dc_cal = (int8_t)(value * rate);
+ else
+ phy_parameter->efuse_usb_dc_cal = -(int8_t)
+ ((EFUS_USB_DC_CAL_MAX & value) * rate);
+
+ if (soc_device_match(rtk_soc_groot)) {
+ dev_dbg(rtk_phy->dev, "For groot IC we need a workaround to adjust efuse_usb_dc_cal\n");
+
+ /* We don't multiple dc_cal_rate=2 for positive dc cal compensate */
+ if (value <= EFUS_USB_DC_CAL_MAX)
+ phy_parameter->efuse_usb_dc_cal = (int8_t)(value);
+
+ /* We set max dc cal compensate is 0x8 if otp is 0x7 */
+ if (value == 0x7)
+ phy_parameter->efuse_usb_dc_cal = (int8_t)(value + 1);
+ }
+ } else { /* for CHECK_EFUSE_V2 */
+ phy_parameter->efuse_usb_dc_cal = value & phy_cfg->dc_driving_mask;
+ }
+
+ /* Read efuse for usb dc disconnect level */
+ value = 0;
+ cell = nvmem_cell_get(rtk_phy->dev, "usb-dc-dis");
+ if (IS_ERR(cell)) {
+ dev_dbg(rtk_phy->dev, "%s no usb-dc-dis: %ld\n",
+ __func__, PTR_ERR(cell));
+ } else {
+ unsigned char *buf;
+ size_t buf_size;
+
+ buf = nvmem_cell_read(cell, &buf_size);
+ if (!IS_ERR(buf)) {
+ value = buf[0] & phy_cfg->dc_disconnect_mask;
+ kfree(buf);
+ }
+ nvmem_cell_put(cell);
+ }
+
+ if (phy_cfg->check_efuse_version == CHECK_EFUSE_V1) {
+ int rate = phy_cfg->efuse_dc_disconnect_rate;
+
+ if (value <= EFUS_USB_DC_DIS_MAX)
+ phy_parameter->efuse_usb_dc_dis = (int8_t)(value * rate);
+ else
+ phy_parameter->efuse_usb_dc_dis = -(int8_t)
+ ((EFUS_USB_DC_DIS_MAX & value) * rate);
+ } else { /* for CHECK_EFUSE_V2 */
+ phy_parameter->efuse_usb_dc_dis = value & phy_cfg->dc_disconnect_mask;
+ }
+
+out:
+ return 0;
+}
+
+static int parse_phy_data(struct rtk_phy *rtk_phy)
+{
+ struct device *dev = rtk_phy->dev;
+ struct device_node *np = dev->of_node;
+ struct phy_parameter *phy_parameter;
+ int ret = 0;
+ int index;
+
+ rtk_phy->phy_parameter = devm_kzalloc(dev, sizeof(struct phy_parameter) *
+ rtk_phy->num_phy, GFP_KERNEL);
+ if (!rtk_phy->phy_parameter)
+ return -ENOMEM;
+
+ for (index = 0; index < rtk_phy->num_phy; index++) {
+ phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index];
+
+ phy_parameter->phy_reg.reg_wrap_vstatus = of_iomap(np, 0);
+ phy_parameter->phy_reg.reg_gusb2phyacc0 = of_iomap(np, 1) + index;
+ phy_parameter->phy_reg.vstatus_index = index;
+
+ if (of_property_read_bool(np, "realtek,inverse-hstx-sync-clock"))
+ phy_parameter->inverse_hstx_sync_clock = true;
+ else
+ phy_parameter->inverse_hstx_sync_clock = false;
+
+ if (of_property_read_u32_index(np, "realtek,driving-level",
+ index, &phy_parameter->driving_level))
+ phy_parameter->driving_level = DEFAULT_DC_DRIVING_VALUE;
+
+ if (of_property_read_u32_index(np, "realtek,driving-level-compensate",
+ index, &phy_parameter->driving_level_compensate))
+ phy_parameter->driving_level_compensate = 0;
+
+ if (of_property_read_u32_index(np, "realtek,disconnection-compensate",
+ index, &phy_parameter->disconnection_compensate))
+ phy_parameter->disconnection_compensate = 0;
+
+ get_phy_data_by_efuse(rtk_phy, phy_parameter, index);
+
+ update_dc_driving_level(rtk_phy, phy_parameter);
+
+ update_hs_clk_select(rtk_phy, phy_parameter);
+ }
+
+ return ret;
+}
+
+static int rtk_usb2phy_probe(struct platform_device *pdev)
+{
+ struct rtk_phy *rtk_phy;
+ struct device *dev = &pdev->dev;
+ struct phy *generic_phy;
+ struct phy_provider *phy_provider;
+ const struct phy_cfg *phy_cfg;
+ int ret = 0;
+
+ phy_cfg = of_device_get_match_data(dev);
+ if (!phy_cfg) {
+ dev_err(dev, "phy config are not assigned!\n");
+ return -EINVAL;
+ }
+
+ rtk_phy = devm_kzalloc(dev, sizeof(*rtk_phy), GFP_KERNEL);
+ if (!rtk_phy)
+ return -ENOMEM;
+
+ rtk_phy->dev = &pdev->dev;
+ rtk_phy->phy_cfg = devm_kzalloc(dev, sizeof(*phy_cfg), GFP_KERNEL);
+
+ memcpy(rtk_phy->phy_cfg, phy_cfg, sizeof(*phy_cfg));
+
+ rtk_phy->num_phy = phy_cfg->num_phy;
+
+ ret = parse_phy_data(rtk_phy);
+ if (ret)
+ goto err;
+
+ platform_set_drvdata(pdev, rtk_phy);
+
+ generic_phy = devm_phy_create(rtk_phy->dev, NULL, &ops);
+ if (IS_ERR(generic_phy))
+ return PTR_ERR(generic_phy);
+
+ phy_set_drvdata(generic_phy, rtk_phy);
+
+ phy_provider = devm_of_phy_provider_register(rtk_phy->dev,
+ of_phy_simple_xlate);
+ if (IS_ERR(phy_provider))
+ return PTR_ERR(phy_provider);
+
+ create_debug_files(rtk_phy);
+
+err:
+ return ret;
+}
+
+static void rtk_usb2phy_remove(struct platform_device *pdev)
+{
+ struct rtk_phy *rtk_phy = platform_get_drvdata(pdev);
+
+ remove_debug_files(rtk_phy);
+}
+
+static const struct phy_cfg rtd1295_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [0] = {0xe0, 0x90},
+ [3] = {0xe3, 0x3a},
+ [4] = {0xe4, 0x68},
+ [6] = {0xe6, 0x91},
+ [13] = {0xf5, 0x81},
+ [15] = {0xf7, 0x02}, },
+ .page1_size = 8,
+ .page1 = { /* default parameter */ },
+ .page2_size = 0,
+ .page2 = { /* no parameter */ },
+ .num_phy = 1,
+ .check_efuse = false,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = 1,
+ .dc_driving_mask = 0xf,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = true,
+ .do_toggle = true,
+ .do_toggle_driving = false,
+ .driving_updated_for_dev_dis = 0xf,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = false,
+};
+
+static const struct phy_cfg rtd1395_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [4] = {0xe4, 0xac},
+ [13] = {0xf5, 0x00},
+ [15] = {0xf7, 0x02}, },
+ .page1_size = 8,
+ .page1 = { /* default parameter */ },
+ .page2_size = 0,
+ .page2 = { /* no parameter */ },
+ .num_phy = 1,
+ .check_efuse = false,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = 1,
+ .dc_driving_mask = 0xf,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = true,
+ .do_toggle = true,
+ .do_toggle_driving = false,
+ .driving_updated_for_dev_dis = 0xf,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = false,
+};
+
+static const struct phy_cfg rtd1395_phy_cfg_2port = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [4] = {0xe4, 0xac},
+ [13] = {0xf5, 0x00},
+ [15] = {0xf7, 0x02}, },
+ .page1_size = 8,
+ .page1 = { /* default parameter */ },
+ .page2_size = 0,
+ .page2 = { /* no parameter */ },
+ .num_phy = 2,
+ .check_efuse = false,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = 1,
+ .dc_driving_mask = 0xf,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = true,
+ .do_toggle = true,
+ .do_toggle_driving = false,
+ .driving_updated_for_dev_dis = 0xf,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = false,
+};
+
+static const struct phy_cfg rtd1619_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [4] = {0xe4, 0x68}, },
+ .page1_size = 8,
+ .page1 = { /* default parameter */ },
+ .page2_size = 0,
+ .page2 = { /* no parameter */ },
+ .num_phy = 1,
+ .check_efuse = true,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = 1,
+ .dc_driving_mask = 0xf,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = true,
+ .do_toggle = true,
+ .do_toggle_driving = false,
+ .driving_updated_for_dev_dis = 0xf,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = false,
+};
+
+static const struct phy_cfg rtd1319_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [0] = {0xe0, 0x18},
+ [4] = {0xe4, 0x6a},
+ [7] = {0xe7, 0x71},
+ [13] = {0xf5, 0x15},
+ [15] = {0xf7, 0x32}, },
+ .page1_size = 8,
+ .page1 = { [3] = {0xe3, 0x44}, },
+ .page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
+ .page2 = { [0] = {0xe0, 0x01}, },
+ .num_phy = 1,
+ .check_efuse = true,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = 1,
+ .dc_driving_mask = 0xf,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = true,
+ .do_toggle = true,
+ .do_toggle_driving = true,
+ .driving_updated_for_dev_dis = 0xf,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = true,
+};
+
+static const struct phy_cfg rtd1312c_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [0] = {0xe0, 0x14},
+ [4] = {0xe4, 0x67},
+ [5] = {0xe5, 0x55}, },
+ .page1_size = 8,
+ .page1 = { [3] = {0xe3, 0x23},
+ [6] = {0xe6, 0x58}, },
+ .page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
+ .page2 = { /* default parameter */ },
+ .num_phy = 1,
+ .check_efuse = true,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = 1,
+ .dc_driving_mask = 0xf,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = true,
+ .do_toggle = true,
+ .do_toggle_driving = true,
+ .driving_updated_for_dev_dis = 0xf,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = true,
+};
+
+static const struct phy_cfg rtd1619b_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [0] = {0xe0, 0xa3},
+ [4] = {0xe4, 0xa8},
+ [5] = {0xe5, 0x4f},
+ [6] = {0xe6, 0x02}, },
+ .page1_size = 8,
+ .page1 = { [3] = {0xe3, 0x64}, },
+ .page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
+ .page2 = { [7] = {0xe7, 0x45}, },
+ .num_phy = 1,
+ .check_efuse = true,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = EFUS_USB_DC_CAL_RATE,
+ .dc_driving_mask = 0x1f,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = false,
+ .do_toggle = true,
+ .do_toggle_driving = true,
+ .driving_updated_for_dev_dis = 0x8,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = true,
+};
+
+static const struct phy_cfg rtd1319d_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [0] = {0xe0, 0xa3},
+ [4] = {0xe4, 0x8e},
+ [5] = {0xe5, 0x4f},
+ [6] = {0xe6, 0x02}, },
+ .page1_size = MAX_USB_PHY_PAGE1_DATA_SIZE,
+ .page1 = { [14] = {0xf5, 0x1}, },
+ .page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
+ .page2 = { [7] = {0xe7, 0x44}, },
+ .check_efuse = true,
+ .num_phy = 1,
+ .check_efuse_version = CHECK_EFUSE_V1,
+ .efuse_dc_driving_rate = EFUS_USB_DC_CAL_RATE,
+ .dc_driving_mask = 0x1f,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = false,
+ .do_toggle = true,
+ .do_toggle_driving = false,
+ .driving_updated_for_dev_dis = 0x8,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = true,
+};
+
+static const struct phy_cfg rtd1315e_phy_cfg = {
+ .page0_size = MAX_USB_PHY_PAGE0_DATA_SIZE,
+ .page0 = { [0] = {0xe0, 0xa3},
+ [4] = {0xe4, 0x8c},
+ [5] = {0xe5, 0x4f},
+ [6] = {0xe6, 0x02}, },
+ .page1_size = MAX_USB_PHY_PAGE1_DATA_SIZE,
+ .page1 = { [3] = {0xe3, 0x7f},
+ [14] = {0xf5, 0x01}, },
+ .page2_size = MAX_USB_PHY_PAGE2_DATA_SIZE,
+ .page2 = { [7] = {0xe7, 0x44}, },
+ .num_phy = 1,
+ .check_efuse = true,
+ .check_efuse_version = CHECK_EFUSE_V2,
+ .efuse_dc_driving_rate = EFUS_USB_DC_CAL_RATE,
+ .dc_driving_mask = 0x1f,
+ .efuse_dc_disconnect_rate = EFUS_USB_DC_DIS_RATE,
+ .dc_disconnect_mask = 0xf,
+ .usb_dc_disconnect_at_page0 = false,
+ .do_toggle = true,
+ .do_toggle_driving = false,
+ .driving_updated_for_dev_dis = 0x8,
+ .use_default_parameter = false,
+ .is_double_sensitivity_mode = true,
+};
+
+static const struct of_device_id usbphy_rtk_dt_match[] = {
+ { .compatible = "realtek,rtd1295-usb2phy", .data = &rtd1295_phy_cfg },
+ { .compatible = "realtek,rtd1312c-usb2phy", .data = &rtd1312c_phy_cfg },
+ { .compatible = "realtek,rtd1315e-usb2phy", .data = &rtd1315e_phy_cfg },
+ { .compatible = "realtek,rtd1319-usb2phy", .data = &rtd1319_phy_cfg },
+ { .compatible = "realtek,rtd1319d-usb2phy", .data = &rtd1319d_phy_cfg },
+ { .compatible = "realtek,rtd1395-usb2phy", .data = &rtd1395_phy_cfg },
+ { .compatible = "realtek,rtd1395-usb2phy-2port", .data = &rtd1395_phy_cfg_2port },
+ { .compatible = "realtek,rtd1619-usb2phy", .data = &rtd1619_phy_cfg },
+ { .compatible = "realtek,rtd1619b-usb2phy", .data = &rtd1619b_phy_cfg },
+ {},
+};
+MODULE_DEVICE_TABLE(of, usbphy_rtk_dt_match);
+
+static struct platform_driver rtk_usb2phy_driver = {
+ .probe = rtk_usb2phy_probe,
+ .remove_new = rtk_usb2phy_remove,
+ .driver = {
+ .name = "rtk-usb2phy",
+ .of_match_table = usbphy_rtk_dt_match,
+ },
+};
+
+module_platform_driver(rtk_usb2phy_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform: rtk-usb2phy");
+MODULE_AUTHOR("Stanley Chang <stanley_chang@...ltek.com>");
+MODULE_DESCRIPTION("Realtek usb 2.0 phy driver");
--
2.34.1
Powered by blists - more mailing lists