| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <20231109104250.GF3752@thinkpad>
Date: Thu, 9 Nov 2023 16:12:50 +0530
From: Manivannan Sadhasivam <mani@...nel.org>
To: Dmitry Baryshkov <dmitry.baryshkov@...aro.org>
Cc: Can Guo <cang@....qualcomm.com>, quic_cang@...cinc.com,
bvanassche@....org, stanley.chu@...iatek.com,
adrian.hunter@...el.com, beanhuo@...ron.com, avri.altman@....com,
junwoo80.lee@...sung.com, martin.petersen@...cle.com,
linux-scsi@...r.kernel.org, Andy Gross <agross@...nel.org>,
Bjorn Andersson <andersson@...nel.org>,
Konrad Dybcio <konrad.dybcio@...aro.org>,
Vinod Koul <vkoul@...nel.org>,
Kishon Vijay Abraham I <kishon@...nel.org>,
"open list:ARM/QUALCOMM SUPPORT" <linux-arm-msm@...r.kernel.org>,
"open list:GENERIC PHY FRAMEWORK" <linux-phy@...ts.infradead.org>,
open list <linux-kernel@...r.kernel.org>
Subject: Re: [PATCH v2 6/7] phy: qualcomm: phy-qcom-qmp-ufs: Add High Speed
Gear 5 support for SM8550
On Thu, Nov 09, 2023 at 11:40:51AM +0200, Dmitry Baryshkov wrote:
> On Thu, 9 Nov 2023 at 05:24, Manivannan Sadhasivam <mani@...nel.org> wrote:
> >
> > On Wed, Nov 08, 2023 at 08:56:16AM +0200, Dmitry Baryshkov wrote:
> > > On Wed, 8 Nov 2023 at 07:49, Manivannan Sadhasivam <mani@...nel.org> wrote:
> > > >
> > > > On Tue, Nov 07, 2023 at 03:18:09PM +0200, Dmitry Baryshkov wrote:
> > > > > On Tue, 7 Nov 2023 at 06:47, Can Guo <cang@....qualcomm.com> wrote:
> > > > > >
> > > > > > From: Can Guo <quic_cang@...cinc.com>
> > > > > >
> > > > > > On SM8550, two sets of UFS PHY settings are provided, one set is to support
> > > > > > HS-G5, another set is to support HS-G4 and lower gears. The two sets of PHY
> > > > > > settings are programming different values to different registers, mixing
> > > > > > the two sets and/or overwriting one set with another set is definitely not
> > > > > > blessed by UFS PHY designers. In order to add HS-G5 support for SM8550, we
> > > > > > need to split the two sets into their dedicated tables, and leave only the
> > > > > > common settings in the .tlbs. To have the PHY programmed with the correct
> > > > > > set of PHY settings, the submode passed to PHY driver must be either HS-G4
> > > > > > or HS-G5.
> > > > > >
> > > >
> > > > You should also mention that this issue is also present in G4 supported targets.
> > > > And a note that it will get fixed later.
> > > >
> > > > > > Signed-off-by: Can Guo <quic_cang@...cinc.com>
> > > > > > ---
> > > > > > drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h | 2 +
> > > > > > drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h | 2 +
> > > > > > .../qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h | 12 +++
> > > > > > drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 112 ++++++++++++++++++---
> > > > > > 4 files changed, 115 insertions(+), 13 deletions(-)
> > > > > >
> > > > > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h
> > > > > > index c23d5e4..e563af5 100644
> > > > > > --- a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h
> > > > > > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v6.h
> > > > > > @@ -18,6 +18,7 @@
> > > > > > #define QPHY_V6_PCS_UFS_BIST_FIXED_PAT_CTRL 0x060
> > > > > > #define QPHY_V6_PCS_UFS_TX_HSGEAR_CAPABILITY 0x074
> > > > > > #define QPHY_V6_PCS_UFS_RX_HSGEAR_CAPABILITY 0x0bc
> > > > > > +#define QPHY_V6_PCS_UFS_RX_HS_G5_SYNC_LENGTH_CAPABILITY 0x12c
> > > > > > #define QPHY_V6_PCS_UFS_DEBUG_BUS_CLKSEL 0x158
> > > > > > #define QPHY_V6_PCS_UFS_LINECFG_DISABLE 0x17c
> > > > > > #define QPHY_V6_PCS_UFS_RX_MIN_HIBERN8_TIME 0x184
> > > > > > @@ -27,5 +28,6 @@
> > > > > > #define QPHY_V6_PCS_UFS_READY_STATUS 0x1a8
> > > > > > #define QPHY_V6_PCS_UFS_TX_MID_TERM_CTRL1 0x1f4
> > > > > > #define QPHY_V6_PCS_UFS_MULTI_LANE_CTRL1 0x1fc
> > > > > > +#define QPHY_V6_PCS_UFS_RX_HSG5_SYNC_WAIT_TIME 0x220
> > > > > >
> > > > > > #endif
> > > > > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h
> > > > > > index f420f8f..ef392ce 100644
> > > > > > --- a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h
> > > > > > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-com-v6.h
> > > > > > @@ -56,6 +56,8 @@
> > > > > > #define QSERDES_V6_COM_SYS_CLK_CTRL 0xe4
> > > > > > #define QSERDES_V6_COM_SYSCLK_BUF_ENABLE 0xe8
> > > > > > #define QSERDES_V6_COM_PLL_IVCO 0xf4
> > > > > > +#define QSERDES_V6_COM_CMN_IETRIM 0xfc
> > > > > > +#define QSERDES_V6_COM_CMN_IPTRIM 0x100
> > > > > > #define QSERDES_V6_COM_SYSCLK_EN_SEL 0x110
> > > > > > #define QSERDES_V6_COM_RESETSM_CNTRL 0x118
> > > > > > #define QSERDES_V6_COM_LOCK_CMP_EN 0x120
> > > > > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
> > > > > > index 15bcb4b..48f31c8 100644
> > > > > > --- a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
> > > > > > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v6.h
> > > > > > @@ -10,10 +10,20 @@
> > > > > > #define QSERDES_UFS_V6_TX_RES_CODE_LANE_RX 0x2c
> > > > > > #define QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_TX 0x30
> > > > > > #define QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_RX 0x34
> > > > > > +#define QSERDES_UFS_V6_TX_LANE_MODE_1 0x7c
> > > > > > +#define QSERDES_UFS_V6_TX_FR_DCC_CTRL 0x108
> > > > > >
> > > > > > #define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE2 0x08
> > > > > > #define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4 0x10
> > > > > > +#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_SO_GAIN_RATE4 0x24
> > > > > > +#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_COUNT_HIGH_RATE4 0x54
> > > > > > +#define QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE2 0xd4
> > > > > > +#define QSERDES_UFS_V6_RX_UCDR_FO_GAIN_RATE4 0xdc
> > > > > > +#define QSERDES_UFS_V6_RX_UCDR_SO_GAIN_RATE4 0xf0
> > > > > > +#define QSERDES_UFS_V6_RX_UCDR_PI_CONTROLS 0xf4
> > > > > > #define QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL 0x178
> > > > > > +#define QSERDES_UFS_V6_RX_EQ_OFFSET_ADAPTOR_CNTRL1 0x1bc
> > > > > > +#define QSERDES_UFS_V6_RX_OFFSET_ADAPTOR_CNTRL3 0x1c4
> > > > > > #define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B0 0x208
> > > > > > #define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B1 0x20c
> > > > > > #define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B3 0x214
> > > > > > @@ -25,6 +35,8 @@
> > > > > > #define QSERDES_UFS_V6_RX_MODE_RATE3_B5 0x264
> > > > > > #define QSERDES_UFS_V6_RX_MODE_RATE3_B8 0x270
> > > > > > #define QSERDES_UFS_V6_RX_MODE_RATE4_B3 0x280
> > > > > > +#define QSERDES_UFS_V6_RX_MODE_RATE4_B4 0x284
> > > > > > #define QSERDES_UFS_V6_RX_MODE_RATE4_B6 0x28c
> > > > > > +#define QSERDES_UFS_V6_RX_DLL0_FTUNE_CTRL 0x2f8
> > > > > >
> > > > > > #endif
> > > > > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> > > > > > index 3927eba..e0a01497 100644
> > > > > > --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> > > > > > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> > > > > > @@ -649,32 +649,51 @@ static const struct qmp_phy_init_tbl sm8550_ufsphy_serdes[] = {
> > > > > > QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x11),
> > > > > > QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_HS_SWITCH_SEL_1, 0x00),
> > > > > > QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x01),
> > > > > > - QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x04),
> > > > > > - QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x0f),
> > > > > > +
> > > > > > QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_INITVAL2, 0x00),
> > > > > > QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41),
> > > > > > - QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x0a),
> > > > > > QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x18),
> > > > > > QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
> > > > > > QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x7f),
> > > > > > QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x06),
> > > > > > - QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x4c),
> > > > > > +};
> > > > > > +
> > > > > > +static const struct qmp_phy_init_tbl sm8550_ufsphy_hs_b_serdes[] = {
> > > > > > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x44),
> > > > > > +};
> > > > > > +
> > > > > > +static const struct qmp_phy_init_tbl sm8550_ufsphy_g4_serdes[] = {
> > > > > > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x04),
> > > > > > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x0f),
> > > > > > QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x0a),
> > > > > > - QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x18),
> > > > > > - QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
> > > > > > - QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x99),
> > > > > > - QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x07),
> > > > >
> > > > > Aside from moving these registers to the HS_G4 table, you are also
> > > > > changing these registers. It makes me think that there was an error in
> > > > > the original programming sequence.
> > > > > If that is correct, could you please split the patch into two pieces:
> > > > > - Fix programming sequence (add proper Fixes tags)
> > > > > - Split G4 and G5 tables.
> > > >
> > > > Ack
> > > >
> > > > >
> > > > > > +
> > > > > > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x4c),
> > > > > > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x0a),
> > > > > > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x18),
> > > > > > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x14),
> > > > > > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x99),
> > > > > > + QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x07),
> > > > >
> > > > > I see all the MODE1 registers being only present in G4 and G5 tables.
> > > > > Should they be programmed for the modes lower than G4?
> > > > >
> > > >
> > > > We use G4 table for all the modes <= G4.
> > >
> > > Could you please point me how it's handled?
> > > In the patch I see just:
> > >
> > > if (qmp->submode == UFS_HS_G4)
> > > qmp_ufs_serdes_init(qmp, &cfg->tbls_hs_g4);
> > > else if (qmp->submode == UFS_HS_G5)
> > > qmp_ufs_serdes_init(qmp, &cfg->tbls_hs_g5);
> > >
> > > Which looks like two special cases (HS_G4 and HS_G5) and nothing for
> > > anything else.
> > >
> >
> > Yes, and the UFS driver passes only G4/G5. For all the gears <=G4, G4 init
> > sequence will be used and for G5, G5 sequence will be used.
> >
>
> That's what I could not find in the UFS driver. I see a call to
> `phy_set_mode_ext(phy, PHY_MODE_UFS_HS_B, host->phy_gear);` and
> host->phy_gear is initialised to UFS_HS_G2.
>
You need to check the UFS driver changes in this series to get the complete
picture as the logic is getting changed.
It is common to get confused because of the way the UFS driver (qcom mostly)
handles the PHY init sequence programming. We used to have only one init
sequence for older targets and life was easy. But when I wanted to add G4
support for SM8250, I learned that there are 2 separate init sequences. One for
non-G4 and other for G4. So I used the phy_sub_mode property to pass the
relevant mode from the UFS driver to the PHY driver and programmed the sequence
accordingly. This got extended to non-G5 and G5 now.
Now, the UFS driver will start probing from a low gear for older targets (G2)
and G4/G5 for newer ones then scale up based on the device and host capability.
For older targets, the common table (tbls) will be used if the submode doesn't
match G4/G5. But for newer targets, the UFS driver will _only_ pass G4 or G5 as
the phy_gear, so those specific sequence will only be used.
Hope I'm clear.
- Mani
> Maybe we should change the condition here (in the PHY driver) to:
>
> if (qmp->submode <= UFS_HS_G4)
>
> ?
> --
> With best wishes
> Dmitry
--
மணிவண்ணன் சதாசிவம்
Powered by blists - more mailing lists