lists.openwall.net   lists  /  announce  owl-users  owl-dev  john-users  john-dev  passwdqc-users  yescrypt  popa3d-users  /  oss-security  kernel-hardening  musl  sabotage  tlsify  passwords  /  crypt-dev  xvendor  /  Bugtraq  Full-Disclosure  linux-kernel  linux-netdev  linux-ext4  linux-hardening  linux-cve-announce  PHC 
Open Source and information security mailing list archives
 
Hash Suite: Windows password security audit tool. GUI, reports in PDF.
[<prev] [next>] [<thread-prev] [day] [month] [year] [list]
Message-ID: <2023110919-properly-each-55f5@gregkh>
Date:   Thu, 9 Nov 2023 15:16:33 +0100
From:   Greg Kroah-Hartman <gregkh@...uxfoundation.org>
To:     Ilpo Järvinen <ilpo.jarvinen@...ux.intel.com>
Cc:     Crescent CY Hsieh <crescentcy.hsieh@...a.com>,
        Jiri Slaby <jirislaby@...nel.org>,
        LKML <linux-kernel@...r.kernel.org>,
        linux-serial <linux-serial@...r.kernel.org>
Subject: Re: [PATCH v3] tty: serial: Add RS422 flag to struct serial_rs485

On Thu, Nov 09, 2023 at 03:35:50PM +0200, Ilpo Järvinen wrote:
> On Wed, 8 Nov 2023, Crescent CY Hsieh wrote:
> 
> > Add "SER_RS485_MODE_RS422" flag to struct serial_rs485, so that serial
> > port can switch interface into RS422 if supported by using ioctl command
> > "TIOCSRS485".
> > 
> > By treating RS422 as a mode of RS485, which means while enabling RS422
> > there are two flags need to be set (SER_RS485_ENABLED and
> > SER_RS485_MODE_RS422), it would make things much easier. For example
> > some places that checks for "SER_RS485_ENABLED" won't need to be rewritten.
> > 
> > There are only two things need to be noticed:
> > 
> > - While enabling RS422, other RS485 flags should not be set.
> > - RS422 doesn't need to deal with termination, so while disabling RS485
> >   or enabling RS422, uart_set_rs485_termination() shall return.
> > 
> > Signed-off-by: Crescent CY Hsieh <crescentcy.hsieh@...a.com>
> > 
> > ---
> > Changes from v2 to v3:
> > - Remove "SER_RS422_ENABLED" flag from legacy flags.
> > - Revise "SER_RS422_ENABLED" into "SER_RS485_MODE_RS422".
> > - Remove the code which checks the conflicts between SER_RS485_ENABLED
> >   and SER_RS422_ENABLED.
> > - Add return check in uart_set_rs485_termination().
> > 
> > Changes from v1 to v2:
> > - Revise the logic that checks whether RS422/RS485 are enabled
> >   simultaneously.
> > 
> > v2: https://lore.kernel.org/all/20231101064404.45711-1-crescentcy.hsieh@moxa.com/
> > v1: https://lore.kernel.org/all/20231030053632.5109-1-crescentcy.hsieh@moxa.com/
> > 
> > ---
> 
> > --- a/include/uapi/linux/serial.h
> > +++ b/include/uapi/linux/serial.h
> > @@ -137,17 +137,19 @@ struct serial_icounter_struct {
> >   * * %SER_RS485_ADDRB		- Enable RS485 addressing mode.
> >   * * %SER_RS485_ADDR_RECV - Receive address filter (enables @addr_recv). Requires %SER_RS485_ADDRB.
> >   * * %SER_RS485_ADDR_DEST - Destination address (enables @addr_dest). Requires %SER_RS485_ADDRB.
> > + * * %SER_RS485_MODE_RS422	- Enable RS422. Requires %SER_RS485_ENABLED.
> >   */
> >  struct serial_rs485 {
> >  	__u32	flags;
> > -#define SER_RS485_ENABLED		(1 << 0)
> > -#define SER_RS485_RTS_ON_SEND		(1 << 1)
> > -#define SER_RS485_RTS_AFTER_SEND	(1 << 2)
> > -#define SER_RS485_RX_DURING_TX		(1 << 4)
> > -#define SER_RS485_TERMINATE_BUS		(1 << 5)
> > -#define SER_RS485_ADDRB			(1 << 6)
> > -#define SER_RS485_ADDR_RECV		(1 << 7)
> > -#define SER_RS485_ADDR_DEST		(1 << 8)
> > +#define SER_RS485_ENABLED		BIT(0)
> > +#define SER_RS485_RTS_ON_SEND		BIT(1)
> > +#define SER_RS485_RTS_AFTER_SEND	BIT(2)
> > +#define SER_RS485_RX_DURING_TX		BIT(3)
> > +#define SER_RS485_TERMINATE_BUS		BIT(4)
> > +#define SER_RS485_ADDRB			BIT(5)
> > +#define SER_RS485_ADDR_RECV		BIT(6)
> > +#define SER_RS485_ADDR_DEST		BIT(7)
> > +#define SER_RS485_MODE_RS422		BIT(8)
> 
> Is BIT() allowed in uapi headers these days?

No, but there is something else that is, can't find it at the moment...

Powered by blists - more mailing lists

Powered by Openwall GNU/*/Linux Powered by OpenVZ