| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <CACRpkdaGzXD6HbiX7mVUNJAJtMEPG00Pp6+nJ1P0JrfJ-ArMvQ@mail.gmail.com>
Date: Tue, 14 Nov 2023 22:59:54 +0100
From: Linus Walleij <linus.walleij@...aro.org>
To: Liu Ying <victor.liu@....com>
Cc: dri-devel@...ts.freedesktop.org, linux-kernel@...r.kernel.org,
andrzej.hajda@...el.com, neil.armstrong@...aro.org,
rfoss@...nel.org, Laurent.pinchart@...asonboard.com,
jonas@...boo.se, jernej.skrabec@...il.com, airlied@...il.com,
daniel@...ll.ch, Ulf Hansson <ulf.hansson@...aro.org>
Subject: Re: [PATCH v3] drm/bridge: panel: Add a device link between drm
device and panel device
On Mon, Aug 7, 2023 at 8:06 AM Liu Ying <victor.liu@....com> wrote:
> Add the device link when panel bridge is attached and delete the link
> when panel bridge is detached. The drm device is the consumer while
> the panel device is the supplier. This makes sure that the drm device
> suspends eariler and resumes later than the panel device, hence resolves
> problems where the order is reversed, like the problematic case mentioned
> in the below link.
>
> Link: https://lore.kernel.org/lkml/CAPDyKFr0XjrU_udKoUKQ_q8RWaUkyqL+8fV-7s1CTMqi7u3-Rg@mail.gmail.com/T/
> Suggested-by: Ulf Hansson <ulf.hansson@...aro.org>
> Signed-off-by: Liu Ying <victor.liu@....com>
> ---
> v2->v3:
> * Improve commit message s/swapped/reversed/.
This patch causes a regression in the Ux500 MCDE
drivers/gpu/drm/mcde/* driver with the nt35510 panel
drivers/gpu/drm/panel/panel-novatek-nt35510.c
my dmesg looks like this:
[ 1.678680] mcde a0350000.mcde: MCDE clk rate 199680000 Hz
[ 1.684448] mcde a0350000.mcde: found MCDE HW revision 3.0 (dev 8,
metal fix 0)
[ 1.692840] mcde-dsi a0351000.dsi: HW revision 0x02327457
[ 1.699310] mcde-dsi a0351000.dsi: attached DSI device with 2 lanes
[ 1.705627] mcde-dsi a0351000.dsi: format 00000000, 24bpp
[ 1.711059] mcde-dsi a0351000.dsi: mode flags: 00000400
[ 1.716400] mcde-dsi a0351000.dsi: registered DSI host
[ 1.722473] mcde-dsi a0352000.dsi: HW revision 0x02327457
[ 1.727874] mcde-dsi a0352000.dsi: registered DSI host
[ 1.733734] mcde-dsi a0353000.dsi: HW revision 0x02327457
[ 1.739135] mcde-dsi a0353000.dsi: registered DSI host
[ 1.814971] mcde-dsi a0351000.dsi: connected to panel
[ 1.820037] mcde-dsi a0351000.dsi: initialized MCDE DSI bridge
[ 1.825958] mcde a0350000.mcde: bound a0351000.dsi (ops
mcde_dsi_component_ops)
[ 1.833312] mcde-dsi a0352000.dsi: unused DSI interface
[ 1.838531] mcde a0350000.mcde: bound a0352000.dsi (ops
mcde_dsi_component_ops)
[ 1.845886] mcde-dsi a0353000.dsi: unused DSI interface
[ 1.851135] mcde a0350000.mcde: bound a0353000.dsi (ops
mcde_dsi_component_ops)
[ 1.858917] [drm:panel_bridge_attach] *ERROR* Failed to add device
link between a0350000.mcde and a0351000.dsi.0
[ 1.869171] [drm:drm_bridge_attach] *ERROR* failed to attach bridge
/soc/mcde@...50000/dsi@...51000/panel to encoder None-34: -22
[ 1.880920] [drm:drm_bridge_attach] *ERROR* failed to attach bridge
/soc/mcde@...50000/dsi@...51000 to encoder None-34: -22
[ 1.892120] mcde a0350000.mcde: failed to attach display output bridge
[ 1.898773] mcde a0350000.mcde: adev bind failed: -22
[ 1.903991] mcde a0350000.mcde: failed to add component master
[ 1.909912] mcde: probe of a0350000.mcde failed with error -22
[ 1.916656] ------------[ cut here ]------------
[ 1.921295] WARNING: CPU: 1 PID: 1 at drivers/regulator/core.c:2996
_regulator_disable+0x130/0x190
[ 1.930297] unbalanced disables for AUX6
[ 1.934265] Modules linked in:
[ 1.937347] CPU: 1 PID: 1 Comm: swapper/0 Not tainted
6.6.0-08649-g7d461b291e65 #3
[ 1.944915] Hardware name: ST-Ericsson Ux5x0 platform (Device Tree Support)
[ 1.951873] unwind_backtrace from show_stack+0x10/0x14
[ 1.957122] show_stack from dump_stack_lvl+0x40/0x4c
[ 1.962188] dump_stack_lvl from __warn+0x84/0xc8
[ 1.966918] __warn from warn_slowpath_fmt+0x124/0x190
[ 1.972076] warn_slowpath_fmt from _regulator_disable+0x130/0x190
[ 1.978271] _regulator_disable from regulator_bulk_disable+0x5c/0x100
[ 1.984802] regulator_bulk_disable from nt35510_remove+0x1c/0x58
[ 1.990905] nt35510_remove from mipi_dsi_drv_remove+0x18/0x20
[ 1.996765] mipi_dsi_drv_remove from
device_release_driver_internal+0x184/0x1f8
[ 2.004180] device_release_driver_internal from bus_remove_device+0xc0/0xe4
[ 2.011230] bus_remove_device from device_del+0x14c/0x464
[ 2.016723] device_del from device_unregister+0xc/0x20
[ 2.021972] device_unregister from mipi_dsi_remove_device_fn+0x34/0x3c
[ 2.028594] mipi_dsi_remove_device_fn from device_for_each_child+0x64/0xa4
[ 2.035583] device_for_each_child from mipi_dsi_host_unregister+0x24/0x50
[ 2.042480] mipi_dsi_host_unregister from platform_remove+0x20/0x5c
[ 2.048858] platform_remove from device_release_driver_internal+0x184/0x1f8
[ 2.055908] device_release_driver_internal from bus_remove_device+0xc0/0xe4
[ 2.062957] bus_remove_device from device_del+0x14c/0x464
[ 2.068450] device_del from platform_device_del.part.0+0x10/0x74
[ 2.074554] platform_device_del.part.0 from
platform_device_unregister+0x18/0x24
[ 2.082061] platform_device_unregister from
of_platform_device_destroy+0x9c/0xac
[ 2.089569] of_platform_device_destroy from
device_for_each_child_reverse+0x78/0xbc
[ 2.097320] device_for_each_child_reverse from
devm_of_platform_populate_release+0x34/0x48
[ 2.105682] devm_of_platform_populate_release from
devres_release_all+0x94/0xf8
[ 2.113098] devres_release_all from device_unbind_cleanup+0xc/0x60
[ 2.119384] device_unbind_cleanup from really_probe+0x1a0/0x2d8
[ 2.125396] really_probe from __driver_probe_device+0x84/0xd4
[ 2.131225] __driver_probe_device from driver_probe_device+0x30/0x104
[ 2.137756] driver_probe_device from __driver_attach+0x90/0x178
[ 2.143768] __driver_attach from bus_for_each_dev+0x7c/0xcc
[ 2.149444] bus_for_each_dev from bus_add_driver+0xcc/0x1cc
[ 2.155120] bus_add_driver from driver_register+0x7c/0x114
[ 2.160705] driver_register from do_one_initcall+0x5c/0x190
[ 2.166381] do_one_initcall from kernel_init_freeable+0x1f8/0x250
[ 2.172576] kernel_init_freeable from kernel_init+0x18/0x12c
[ 2.178344] kernel_init from ret_from_fork+0x14/0x28
[ 2.183410] Exception stack(0xf08c5fb0 to 0xf08c5ff8)
[ 2.188446] 5fa0: 00000000
00000000 00000000 00000000
[ 2.196624] 5fc0: 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000
[ 2.204803] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 2.211486] ---[ end trace 0000000000000000 ]---
[ 2.216125] Failed to disable vddi: -EIO
[ 2.220062] panel-novatek-nt35510 a0351000.dsi.0: Failed to power off
Reverting the patch solves the problem.
See device tree at e.g.:
arch/arm/boot/dts/st/ste-ux500-samsung-skomer.dts
The usual problems with patches like this is that our DSI panel
is attached in the DT without any graph:
mcde@...50000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dsi_default_mode>;
dsi@...51000 {
panel {
/* NT35510-based Hydis HVA40WV1 */
compatible = "hydis,hva40wv1",
"novatek,nt35510";
reg = <0>;
/* v_lcd_3v0 2.3-4.8V */
vdd-supply = <&ab8500_ldo_aux4_reg>;
/* v_lcd_1v8 1.65-3.3V */
vddi-supply = <&ab8500_ldo_aux6_reg>;
/* GPIO 139 */
reset-gpios = <&gpio4 11
GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&display_default_mode>;
backlight = <&ktd253>;
};
};
};
The DSI bridge is inside the display controller (MCDE) and the panel is
right inside the DSI bridge.
Suggestions welcome, I'm clueless why this happens.
Yours,
Linus Walleij
Powered by blists - more mailing lists