[<prev] [next>] [<thread-prev] [thread-next>] [day] [month] [year] [list]
Message-Id: <20231118123205.266819-6-arinc.unal@arinc9.com>
Date: Sat, 18 Nov 2023 15:31:55 +0300
From: Arınç ÜNAL <arinc.unal@...nc9.com>
To: Arınç ÜNAL <arinc.unal@...nc9.com>,
Daniel Golle <daniel@...rotopia.org>,
Landen Chao <Landen.Chao@...iatek.com>,
DENG Qingfang <dqfext@...il.com>,
Sean Wang <sean.wang@...iatek.com>,
Andrew Lunn <andrew@...n.ch>,
Florian Fainelli <f.fainelli@...il.com>,
Vladimir Oltean <olteanv@...il.com>,
"David S. Miller" <davem@...emloft.net>,
Eric Dumazet <edumazet@...gle.com>,
Jakub Kicinski <kuba@...nel.org>,
Paolo Abeni <pabeni@...hat.com>,
Matthias Brugger <matthias.bgg@...il.com>,
AngeloGioacchino Del Regno
<angelogioacchino.delregno@...labora.com>,
Russell King <linux@...linux.org.uk>
Cc: netdev@...r.kernel.org, linux-kernel@...r.kernel.org,
linux-arm-kernel@...ts.infradead.org,
linux-mediatek@...ts.infradead.org,
Frank Wunderlich <frank-w@...lic-files.de>,
Bartel Eerdekens <bartel.eerdekens@...stell8.be>,
mithat.guner@...ont.com, erkin.bozoglu@...ont.com
Subject: [PATCH net-next 05/15] net: dsa: mt7530: improve code path for setting up port 5
There're two code paths for setting up port 5:
mt7530_setup()
-> mt7530_setup_port5()
mt753x_phylink_mac_config()
-> mt753x_mac_config()
-> mt7530_mac_config()
-> mt7530_setup_port5()
Currently mt7530_setup_port5() from mt7530_setup() always runs. If port 5
is used as a CPU, DSA, or user port, mt7530_setup_port5() from
mt753x_phylink_mac_config() won't run. That is because priv->p5_interface
set on mt7530_setup_port5() will match state->interface on
mt753x_phylink_mac_config() which will stop running mt7530_setup_port5()
again.
Therefore, mt7530_setup_port5() will never run from
mt753x_phylink_mac_config().
Address this by not running mt7530_setup_port5() from mt7530_setup() if
port 5 is used as a CPU, DSA, or user port. This driver isn't in the
dsa_switches_apply_workarounds[] array so phylink will always be present.
For the cases of PHY muxing or the port being disabled, call
mt7530_setup_port5() from mt7530_setup(). mt7530_setup_port5() from
mt753x_phylink_mac_config() won't run when port 5 is disabled or used for
PHY muxing as port 5 won't be defined on the devicetree.
Do not set priv->p5_intf_sel to P5_DISABLED. It is already set to that when
"priv" is allocated.
Move setting the interface to a more specific location. It's supposed to be
overwritten if PHY muxing is detected.
Improve the comment which explains the process.
Signed-off-by: Arınç ÜNAL <arinc.unal@...nc9.com>
---
drivers/net/dsa/mt7530.c | 17 ++++++++---------
1 file changed, 8 insertions(+), 9 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 8623742b35ee..069b3dfca6fa 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2308,16 +2308,15 @@ mt7530_setup(struct dsa_switch *ds)
return ret;
/* Setup port 5 */
- priv->p5_intf_sel = P5_DISABLED;
- interface = PHY_INTERFACE_MODE_NA;
-
if (!dsa_is_unused_port(ds, 5)) {
priv->p5_intf_sel = P5_INTF_SEL_GMAC5;
- ret = of_get_phy_mode(dsa_to_port(ds, 5)->dn, &interface);
- if (ret && ret != -ENODEV)
- return ret;
} else {
- /* Scan the ethernet nodes. look for GMAC1, lookup used phy */
+ /* Scan the ethernet nodes. Look for GMAC1, lookup the used PHY.
+ * Set priv->p5_intf_sel to the appropriate value if PHY muxing
+ * is detected.
+ */
+ interface = PHY_INTERFACE_MODE_NA;
+
for_each_child_of_node(dn, mac_np) {
if (!of_device_is_compatible(mac_np,
"mediatek,eth-mac"))
@@ -2348,6 +2347,8 @@ mt7530_setup(struct dsa_switch *ds)
of_node_put(phy_node);
break;
}
+
+ mt7530_setup_port5(ds, interface);
}
#ifdef CONFIG_GPIOLIB
@@ -2358,8 +2359,6 @@ mt7530_setup(struct dsa_switch *ds)
}
#endif /* CONFIG_GPIOLIB */
- mt7530_setup_port5(ds, interface);
-
/* Flush the FDB table */
ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
if (ret < 0)
--
2.40.1
Powered by blists - more mailing lists