| lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
|
Open Source and information security mailing list archives
| ||
|
Message-ID: <d63ebc5f-9b72-4457-949b-3e90883bd3c0@molgen.mpg.de>
Date: Sun, 19 Nov 2023 23:09:32 +0100
From: Paul Menzel <pmenzel@...gen.mpg.de>
To: Alan Stern <stern@...land.harvard.edu>
Cc: Marcel Holtmann <marcel@...tmann.org>,
Johan Hedberg <johan.hedberg@...il.com>,
Luiz Augusto von Dentz <luiz.dentz@...il.com>,
linux-bluetooth@...r.kernel.org, linux-kernel@...r.kernel.org,
linux-usb@...r.kernel.org, linux-pm@...r.kernel.org,
Hans de Goede <hdegoede@...hat.com>
Subject: Re: Qualcomm Atheros QCA61x4 keeps drawing 0.85 W despite Bluetooth
being disable in GNOME
Dear Alan,
Thank you very much for your quick response.
Am 19.11.23 um 16:43 schrieb Alan Stern:
> On Sun, Nov 19, 2023 at 02:42:58PM +0100, Paul Menzel wrote:
>> On the Dell XPS 13 9360 from 2016, BIOS 2.21.0 06/02/2022, with Debian
>> sid/unstable and Debian’s Linux 6.5.10 kernel, I am trying to extend the
>> run-time with battery, at under 50 % of it’s original capacity, and I am
>> using PowerTOP 2.15.
>
>> Although radio/wireless devices are turned off in GNOME, PowerTOP shows the
>> Bluetooth device drawing 0.85 W of energy:
>>
>> 848 mW 100.0% Device USB device: usb-device-0cf3-e300
>>
>> $ lsusb -d 0cf3:e300
>> Bus 001 Device 002: ID 0cf3:e300 Qualcomm Atheros Communications QCA61x4 Bluetooth 4.0
>
>> After unloading the module `btusb`, the entry disappears from the PowerTOP
>> list after a while.
>>
>> usbcore: deregistering interface driver btusb
>>
>> Auto-suspend was enabled for the device. (Though it shouldn’t have mattered
>> as it was disabled in GNOME?)
>
> Enabling autosuspend means that the device _may_ go into runtime suspend
> when it's not being used. Whether it _will_ do so depends on the driver
> (btusb in this case).
Thank you for the clarification.
>> Anyways, have you heard of such an issue? Can I provide more information, to
>> get it to not use any energy while being disable in GNOME?
>
> What is the output from
>
> grep . /sys/bus/usb/devices/1-3/power/*
>
> both with and without the btusb module loaded?
```
$ sudo modprobe btusb
$ sudo dmesg | tail -10
[313699.136637] wlp58s0: Limiting TX power to 17 dBm as advertised by
00:f6:63:af:fa:4f
[314037.905400] WARNING! power/level is deprecated; use power/control
instead
[314065.418431] usbcore: registered new interface driver btusb
[314065.421509] bluetooth hci0: firmware: direct-loading firmware
qca/rampatch_usb_00000302.bin
[314065.423852] Bluetooth: hci0: using rampatch file:
qca/rampatch_usb_00000302.bin
[314065.423865] Bluetooth: hci0: QCA: patch rome 0x302 build 0x3e8,
firmware rome 0x302 build 0x111
[314065.791131] bluetooth hci0: firmware: direct-loading firmware
qca/nvm_usb_00000302.bin
[314065.791228] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[314065.823499] Bluetooth: hci0: HCI Enhanced Setup Synchronous
Connection command is advertised, but not supported.
[314066.117644] Bluetooth: MGMT ver 1.22
$ grep . /sys/bus/usb/devices/1-3/power/*
/sys/bus/usb/devices/1-3/power/active_duration:119053224
/sys/bus/usb/devices/1-3/power/async:enabled
/sys/bus/usb/devices/1-3/power/autosuspend:2
/sys/bus/usb/devices/1-3/power/autosuspend_delay_ms:2000
/sys/bus/usb/devices/1-3/power/connected_duration:148065372
/sys/bus/usb/devices/1-3/power/control:auto
/sys/bus/usb/devices/1-3/power/level:auto
/sys/bus/usb/devices/1-3/power/persist:1
/sys/bus/usb/devices/1-3/power/runtime_active_kids:0
/sys/bus/usb/devices/1-3/power/runtime_active_time:119060567
/sys/bus/usb/devices/1-3/power/runtime_enabled:enabled
/sys/bus/usb/devices/1-3/power/runtime_status:active
/sys/bus/usb/devices/1-3/power/runtime_suspended_time:28831453
/sys/bus/usb/devices/1-3/power/runtime_usage:0
/sys/bus/usb/devices/1-3/power/wakeup:disabled
```
```
$ sudo modprobe -r btusb
$ sudo dmesg | tail -1
[314106.155163] usbcore: deregistering interface driver btusb
$ grep . /sys/bus/usb/devices/1-3/power/*
/sys/bus/usb/devices/1-3/power/active_duration:119072176
/sys/bus/usb/devices/1-3/power/async:enabled
/sys/bus/usb/devices/1-3/power/autosuspend:2
/sys/bus/usb/devices/1-3/power/autosuspend_delay_ms:2000
/sys/bus/usb/devices/1-3/power/connected_duration:148320980
/sys/bus/usb/devices/1-3/power/control:auto
/sys/bus/usb/devices/1-3/power/level:auto
/sys/bus/usb/devices/1-3/power/persist:1
/sys/bus/usb/devices/1-3/power/runtime_active_kids:0
/sys/bus/usb/devices/1-3/power/runtime_active_time:119079518
/sys/bus/usb/devices/1-3/power/runtime_enabled:enabled
/sys/bus/usb/devices/1-3/power/runtime_status:suspended
/sys/bus/usb/devices/1-3/power/runtime_suspended_time:29068110
/sys/bus/usb/devices/1-3/power/runtime_usage:0
/sys/bus/usb/devices/1-3/power/wakeup:disabled
```
Kind regards,
Paul
>> $ lsusb -t
>> /: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 10000M
>> |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 10000M
>> |__ Port 2: Dev 3, If 0, Class=Vendor Specific Class, Driver=r8152, 5000M
>> /: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 480M
>> |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/5p, 480M
>> |__ Port 1: Dev 3, If 0, Class=Human Interface Device,
>> Driver=usbhid, 12M
>> /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M
>> /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/12p, 480M
>> |__ Port 3: Dev 2, If 0, Class=Wireless, Driver=, 12M
>> |__ Port 3: Dev 2, If 1, Class=Wireless, Driver=, 12M
>> |__ Port 4: Dev 3, If 0, Class=Human Interface Device, Driver=usbhid, 12M
>> |__ Port 5: Dev 4, If 0, Class=Video, Driver=uvcvideo, 480M
>> |__ Port 5: Dev 4, If 1, Class=Video, Driver=uvcvideo, 480M
>> ```
Powered by blists - more mailing lists