lists.openwall.net | lists / announce owl-users owl-dev john-users john-dev passwdqc-users yescrypt popa3d-users / oss-security kernel-hardening musl sabotage tlsify passwords / crypt-dev xvendor / Bugtraq Full-Disclosure linux-kernel linux-netdev linux-ext4 linux-hardening linux-cve-announce PHC | |
Open Source and information security mailing list archives
| ||
|
Message-Id: <20231201001423.20989-12-ansuelsmth@gmail.com> Date: Fri, 1 Dec 2023 01:14:21 +0100 From: Christian Marangi <ansuelsmth@...il.com> To: Andrew Lunn <andrew@...n.ch>, Heiner Kallweit <hkallweit1@...il.com>, Russell King <linux@...linux.org.uk>, "David S. Miller" <davem@...emloft.net>, Eric Dumazet <edumazet@...gle.com>, Jakub Kicinski <kuba@...nel.org>, Paolo Abeni <pabeni@...hat.com>, netdev@...r.kernel.org, linux-kernel@...r.kernel.org Cc: Christian Marangi <ansuelsmth@...il.com> Subject: [net-next PATCH v2 11/12] net: phy: at803x: move at8035 specific DT parse to dedicated probe Move at8035 specific DT parse for clock out frequency to dedicated probe to make at803x probe function more generic. This is to tidy code and no behaviour change are intended. Detection logic is changed, we check if the clk 25m mask is set and if it's not zero, we assume the qca,clk-out-frequency property is set. The property is checked in the generic at803x_parse_dt called by at803x_probe. Signed-off-by: Christian Marangi <ansuelsmth@...il.com> --- drivers/net/phy/at803x.c | 60 +++++++++++++++++++++++++++------------- 1 file changed, 41 insertions(+), 19 deletions(-) diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c index 73d1a5e29202..27dc0a9ca076 100644 --- a/drivers/net/phy/at803x.c +++ b/drivers/net/phy/at803x.c @@ -638,23 +638,6 @@ static int at803x_parse_dt(struct phy_device *phydev) priv->clk_25m_reg |= FIELD_PREP(AT803X_CLK_OUT_MASK, sel); priv->clk_25m_mask |= AT803X_CLK_OUT_MASK; - - /* Fixup for the AR8030/AR8035. This chip has another mask and - * doesn't support the DSP reference. Eg. the lowest bit of the - * mask. The upper two bits select the same frequencies. Mask - * the lowest bit here. - * - * Warning: - * There was no datasheet for the AR8030 available so this is - * just a guess. But the AR8035 is listed as pin compatible - * to the AR8030 so there might be a good chance it works on - * the AR8030 too. - */ - if (phydev->drv->phy_id == ATH8030_PHY_ID || - phydev->drv->phy_id == ATH8035_PHY_ID) { - priv->clk_25m_reg &= AT8035_CLK_OUT_MASK; - priv->clk_25m_mask &= AT8035_CLK_OUT_MASK; - } } ret = of_property_read_u32(node, "qca,clk-out-strength", &strength); @@ -1637,6 +1620,45 @@ static int at8031_config_intr(struct phy_device *phydev) return at803x_config_intr(phydev); } +static int at8035_parse_dt(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + + /* Mask is set by the generic at803x_parse_dt + * if property is set. Assume property is set + * with the mask not zero. + */ + if (priv->clk_25m_mask) { + /* Fixup for the AR8030/AR8035. This chip has another mask and + * doesn't support the DSP reference. Eg. the lowest bit of the + * mask. The upper two bits select the same frequencies. Mask + * the lowest bit here. + * + * Warning: + * There was no datasheet for the AR8030 available so this is + * just a guess. But the AR8035 is listed as pin compatible + * to the AR8030 so there might be a good chance it works on + * the AR8030 too. + */ + priv->clk_25m_reg &= AT8035_CLK_OUT_MASK; + priv->clk_25m_mask &= AT8035_CLK_OUT_MASK; + } + + return 0; +} + +/* AR8030 and AR8035 shared the same special mask for clk_25m */ +static int at8035_probe(struct phy_device *phydev) +{ + int ret; + + ret = at803x_probe(phydev); + if (ret) + return ret; + + return at8035_parse_dt(phydev); +} + static int qca83xx_config_init(struct phy_device *phydev) { u8 switch_revision; @@ -2109,7 +2131,7 @@ static struct phy_driver at803x_driver[] = { PHY_ID_MATCH_EXACT(ATH8035_PHY_ID), .name = "Qualcomm Atheros AR8035", .flags = PHY_POLL_CABLE_TEST, - .probe = at803x_probe, + .probe = at8035_probe, .config_aneg = at803x_config_aneg, .config_init = at803x_config_init, .soft_reset = genphy_soft_reset, @@ -2130,7 +2152,7 @@ static struct phy_driver at803x_driver[] = { .phy_id = ATH8030_PHY_ID, .name = "Qualcomm Atheros AR8030", .phy_id_mask = AT8030_PHY_ID_MASK, - .probe = at803x_probe, + .probe = at8035_probe, .config_init = at803x_config_init, .link_change_notify = at803x_link_change_notify, .set_wol = at803x_set_wol, -- 2.40.1
Powered by blists - more mailing lists